Onkyo D-407F Handleiding

Onkyo Speaker D-407F

Lees hieronder de 📖 handleiding in het Nederlandse voor Onkyo D-407F (8 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 54 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/8
En tC
Instruction Manual
Thank you for your purchase of the Onkyo speaker
system.
Please read this manual thoroughly before using it.
Following the instructions in this manual will enable you
to obtain optimum performance and listening enjoyment
from your new speaker system.
Please retain this manual for future reference.
使用手冊
謝謝閣下購買 Onkyo 的揚聲器系統。
在連接各部件及接通電源之前， 請先徹底閱讀本手冊。
遵從本手冊內的各項指示， 使您的揚聲器系統能夠獲得
最優秀的性能和欣賞效果， 您將能獲得最大樂趣。
請保存此手冊以備將來參考之用。
D-407F
Speaker System Before using this unit En-2
使用本系統之前 Ct-2
Precaution on use En-2
使用注意事項 Ct-2
Connection En-2
連接 Ct-2
Mounting the stand
attachment En-3
安裝站立支架附件 Ct-3
Placement En-3
安放 Ct-3
Attaching and detaching
the speaker grilles En-3
揚聲器前格板的安裝和拆除 Ct-3
Use with a TV set En-4
作為電視機的外接揚聲器
使用時 Ct-4
Speaker care En-4
揚聲器的維護保養 Ct-4
Specifications En-4
規格 Ct-4
En-2
Connection
• Turn the sound volume to the minimum and disconnect the
power cord from the amplifier before connecting the
speaker cables.
• The nominal impedance of this speaker system is 6 . UseΩ
only amplifiers capable of handling this impedance.
• Use the supplied speaker cables to connect between
speaker’s input terminals and the amplifier’s speaker
terminals as illustrated below.
• Connect the speaker cables securely to the terminals, with
the core wires twisted properly. In this case, make sure that
the core wires do not touch each other. Note that a short
circuit in core wires may result in damage to the amplifier.
Before using this unit
• The speaker cabinet is made of wood and is therefore
sensitive to extreme temperatures and humidity. Avoid
placing the speaker systems in locations subjected to
direct sunlight, or in smoky or in humid places, such as
near an air conditioner, humidifier, bathroom, or kitchen.
Doing so may result in damage to the speaker.
• Place the unit on a rigid, level surface. Placing it on a
slanted surface or weak base not only may cause the unit
to fall, but also results in decreased sound quality.
• Be sure to turn off your amplifier before connecting the
speaker system. Connecting them with the amplifier’s
power on may result in damage to the amplifier or the
speaker system.
• Keep water or other liquids away from the unit. If water is
spilled into the unit, not only the unit but also the speakers
themselves may be damaged.
Precaution on use
• This speaker system can handle the specified input power
when it is used for ordinary music reproduction. If the
following abnormal signals are fed to the speaker,
however, an overcurrent may flow in the internal circuits,
causing burning or breakage of the wires even if the input
power is below the specified rating.
1. Noise produced when FM station is not tuned in
2. Sound produced when fast-forwarding cassette tape
deck
3. High-frequency sound generated by an oscillator, an
electronic musical instruments, etc.
4. Oscillating amplifier signals
5. Special test signals produced by audio checking CD,
etc.
6. Sound produced when connecting or disconnecting
audio connection cables (Always turn off the amplifier’s
power before connecting or disconnecting cables.)
7. Howling when a microphone is used
• Do not place magnetic objects such as screwdrivers and
iron parts near the tweeter since they use speakers with
strong magnets. Otherwise, the objects may be attracted,
causing injury or damaging the diaphragm.
Before turning on the amplifier’s power switch:
• Make sure that the positive (+) and negative (–) speaker
cables do not contact each other. Otherwise, a short-circuit
may occur, causing damage to the amplifier.
• Be sure to connect the speaker cables with correct polarity
(connect the speaker’s positive (+) and negative (–)
binding posts with the amplifier’s corresponding speaker
terminals). Reversed polarity results in impaired bass-
range reproduction, causing mislocalization of the sound
image. Also, be sure to connect the Right and Left
speakers with the amplifier’s corresponding speaker
terminals.
• Pull lightly on the speaker cables to ensure that they are
connected firmly.
Connecting to AV amplifier
R L
1. Strip off the end
of plastic skin,
and give a twist
to the core wire.
2. Slacken the
screw and thread
the core wire
deep enough
into the hole.
3. Hold the core wire
tight by fastening
the screw in the
direction of an
arrow.
Right hand side
speaker (R Channel)
Left hand side speaker
(L Channel)
Red cord side Red cord side
Speaker terminals of the amplifier
15mm
En-3
Mounting the stand attachment
A set of tip-resistant accessories is included with shipment:
300mm long stand attachment and M4 x 35mm screws. Mount
the stand attachment in the bottom of backside the cabinet
using a screwdriver.
Placement
D-407F Front speaker system
The sound quality a speaker system reproduces varies greatly
depending on the construction and area of the room where it is
installed, as well as the location and size of the furniture. For
better-quality sound, observe the following precautions.
•Avoid placing the speaker system on an elevated object
such as on concrete blocks. Instead, place it on a rigid floor
surface with minimal vibration. Also note that high-quality
bass cannot be obtained if the speaker system is unstably
positioned. Generally speaking, placing the speaker
system on several small-diameter supports results in
better bass than placing it directly on the installation
surface. Moreover, if you feel the bass reproduced by the
system is too weak, move the speaker system closer to the
wall behind it. You can thus control the strength of the
reproduced bass by the position of the speakers.
•In many rooms, the furniture and wall affect the
reproduced sound quality. For stereo sound reproduction,
placing the Right and Left speakers in the same condition
produces the best results. If they are placed in extremely
different conditions, the Right- and Left-channel balance
will be adversely affected.
•The ideal placement of the speaker system is as follows:
Imagine an equilateral triangle and position the Right and
Left speakers on both ends of the base. The ideal listening
position is at or slightly to the rear of the triangle apex.
•Glazed doors or surrounding walls in front of the speaker
system may cause the resonance of specific frequency
ranges due to reflected sound. To eliminate this
resonance, place some sound-absorbing material such as
a thick curtain in front of the doors or walls.
Attaching and detaching the speaker grilles
This speaker system uses detachable grilles. Use the
following method to attach or detach the grilles.
1. While holding the bottom edge of the speaker grille with
your both hands, pull it gently toward you to remove the
bottom of the grille.
2. In the same way, gently pull the upper edge of the speaker
grille toward you to remove it from the main unit.
3. To replace the grill, push the projections at the corners into
the grille plug holes on the speaker cabinet.
•Exercise due care to install and secure the cabinet; the
sustainability of the screws may vary depending on the
quality and/or location of the wall where they are tightened.
You may want to consult with a professional installer.
Screwdriver
Backside of the
speaker
Screws Stand attachment
Cup hook,
about 4 mm in
diameter and
15 mm long
Secure the
cabinet to the
wall, etc.
Durable cord
or chain
Caution:
•Allow for secure placement of the speaker; the cabinet is
very tall and tends to fall down under unstable conditions.
Do not place it on an unstable location such as shaky or
sloping table, platform or thick carpet. Otherwise it could
cause injury when dropping or falling.
•You can secure the cabinet to the wall, etc. by using a
durable cord or chain along with cup hooks: Find a hole on
the either side of backside the cabinet, and screw into
each hole the cup hook of about 4mm in diameter and
15mm long, and then secure the cabinet to the wall, etc.
with the cord or chain.
D-407F
Removal Replacement

Product specificaties

Merk: Onkyo
Categorie: Speaker
Model: D-407F

Heb je hulp nodig?

Als je hulp nodig hebt met Onkyo D-407F stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Speaker Onkyo

Onkyo

Onkyo HT-S3405 Handleiding

22 Juni 2023
Onkyo

Onkyo HTP-2S Handleiding

27 Mei 2023
Onkyo

Onkyo SKS-4700 Handleiding

23 Mei 2023
Onkyo

Onkyo SKS-3600 Handleiding

5 Mei 2023
Onkyo

Onkyo D-407F Handleiding

2 Mei 2023
Onkyo

Onkyo D-309H Handleiding

1 Mei 2023
Onkyo

Onkyo SKS-HT230 Handleiding

16 April 2023
Onkyo

Onkyo SKR-L500 Handleiding

11 April 2023
Onkyo

Onkyo SKS-101 Handleiding

10 April 2023
Onkyo

Onkyo Smart Speaker G3 VC-GX30 Handleiding

4 April 2023

Handleiding Speaker

Nieuwste handleidingen voor Speaker

Kramer

Kramer Tavor 8-Sub Handleiding

21 November 2024
Kramer

Kramer Galil 6-AW Handleiding

21 November 2024
Extron

Extron SM 28 Handleiding

21 November 2024
JBL

JBL RM10 Handleiding

20 November 2024
JBL

JBL Performance IS6 Handleiding

20 November 2024
JBL

JBL Power P-Kit Handleiding

20 November 2024
JBL

JBL Performance P941 Handleiding

20 November 2024
JBL

JBL Performance P52OWS Handleiding

20 November 2024
JBL

JBL Performance PC600 Handleiding

20 November 2024
JBL

JBL Performance IS6DT Handleiding

20 November 2024