Onkyo SKF-L500 Handleiding

Onkyo Speaker SKF-L500

Lees hieronder de 📖 handleiding in het Nederlandse voor Onkyo SKF-L500 (4 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 53 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
E
n
Speaker System
SKF-L500
Instruction Manual
Thank you for purchasing an Onkyo speaker system.
Please read this manual thoroughly before using your
new speakers. Following the instructions in this
manual will enable you to obtain optimum
performance and listening enjoyment from your
speaker system.
Please retain this manual for future reference.
Contents
Getting Started
Package Contents ........................... 2
Placement ........................................ 2
Installing & Using
Speaker Bases ................................ 2
Connecting the Speakers............... 3
Appendix
Operating Precautions ................... 3
Speaker care.................................... 4
Use with a TV set or computer....... 4
Specifications.................................. 4
SKF-L500.fm Page 1 Monday, October 3, 2005 4:55 PM
2
SKF-L500: Front speaker
×
2
Speaker cable, 4.5 m
×
2 (red, white)
Cork spacers
×
8
Speaker base
×
2
Bass fixing screws
×
8
SKF-L500: Front left and right speakers
These output the overall sound. Their role in a home
theater is to provide a solid anchor for the sound image.
They should be positioned facing the listener at about
ear level, and equidistant from the TV. Angle them
inward so as to create a triangle, with the listener at the
apex.
The speaker cabinets are sensitive to extreme temper-
atures and humidity, do not put them in locations sub-
ject to direct sunlight or in humid places, such as near
an air conditioner, humidifier, bathroom, or kitchen.
Do not put water or other liquids close to the speak-
ers. If liquid is spilled over the speakers, the drive
units may be damaged.
Using the supplied cork spacers
We recommend using
the supplied cork spac-
ers to achieve the best
possible sound from
your speakers. The cork
spacers prevent the
speakers from moving,
providing a more stable
setup.
Attaching the speaker bases
Before you connect the speakers, attach the supplied
speaker base to each SKF-L500.
1. Turn the speaker upside down.
2. Align the screw holes on the speaker base with
those on the bottom of each speaker, and affix the
speaker base using the supplied screws.
SAFETY PRECAUTIONS:
Attach the speaker bases on a flat, level, and stable
floor.
After you attach the speaker bases, make sure that the
speakers stand upright and are stable.
Using the speaker cable hook
Each supplied speaker base features a speaker cable
hook. It is recommended that you pass the cables
through the hook to avoid tangled cables.
Preventing the speakers from falling
To install the speakers securely, remove the seal from
the upper rear part of each speaker to expose a small
hole. Install an eye hook into the hole, then secure the
speaker against the wall using a cord.
Package Contents
Placement
Speaker Bases
SKF-L500
Cork spacers
Bottom of speaker base
Bottom of
SKF-L500
Speaker base
Supplied screws
Speaker cable
Speaker cable
hook
Speaker base
Top of SKF-L500
Eye hook
Secure the speaker
against the wall using
a cord.
SKF-L500.fm Page 2 Monday, October 3, 2005 4:55 PM
3
Read the following before connecting your speakers:
Turn off your amp before making any connections.
The nominal impedance of these speakers is 6
. Use
only an amp that supports this impedance.
Pay close attention to speaker wiring polarity. Con-
nect positive (+) terminals to only positive (+) termi-
nals, and negative (–) terminals to only negative (–)
terminals. If the speakers are wired incorrectly, the
sound will be out of phase and will sound unnatural.
Be careful not to short the
positive and negative wires.
Doing so may damage your
amp.
Connecting the Speaker Cables
The speakers can handle the specified input power when
used for normal music reproduction. If any of the fol-
lowing signals are fed to them, even if the input power
is within the specified rating, excessive current may
flow in the speaker coils, causing burning or wire break-
age:
1.
Interstation noise from an untuned FM radio.
2.
Sound from fast-forwarding a cassette tape.
3.
High-pitched sounds generated by an oscillator, elec-
tronic musical instrument, and so on.
4.
Amplifier oscillation.
5.
Special test tones from audio test CDs and so on.
6.
Thumps and clicks caused by connecting or discon-
necting audio cables (Always turn off your amplifier
before connecting or disconnecting cables.)
7.
Microphone feedback.
The speakers contain strong magnets, so do not put
magnetic or iron objects such as screwdrivers close to
them. If you do, the object may be attached to the
magnets, causing personal injury or damage to the
diaphragm.
Connecting the Speakers
1
Strip the insulation from the
ends of the speaker cables,
and twist the bare wires tightly.
2
Use the cables to connect each speaker’s
input terminals to the corresponding
speaker output terminals on your amp.
To make a connection, while
pressing the terminal lever,
insert the wire into the hole, and
then release the lever.
Make sure that the terminals are
gripping the bare wires, not the insulation.
FRONT
SPEAKERS
CENTER
SPEAKER
SURROUND
SPEAKERS
R
L
SURROUND BACK SPEAKERS
SKF-L500
Front right speaker
SKF-L500
Front left speaker
SKC-L500C
Center speaker
SKM-L500S
Surround right
speaker
SKM-L500S
Surround left
speaker
RedWhite
SKR-L500
Surround back
speaker
SKR-L500
Surround back
speaker
Operating Precautions
SKF-L500.fm Page 3 Monday, October 3, 2005 4:55 PM


Product specificaties

Merk: Onkyo
Categorie: Speaker
Model: SKF-L500

Heb je hulp nodig?

Als je hulp nodig hebt met Onkyo SKF-L500 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Speaker Onkyo

Handleiding Speaker

Nieuwste handleidingen voor Speaker