Onkyo ONKD525B Handleiding

Onkyo Speaker ONKD525B

Lees hieronder de 📖 handleiding in het Nederlandse voor Onkyo ONKD525B (4 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 46 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Speaker System

D-525

D-425

D-325

Instruction Manual

Thank you for purchasing an Onkyo Speaker

System.

Please read this manual thoroughly before using

it. Following the instructions in this manual will

enable you to obtain optimum performance and

listening enjoyment from your new Speaker Sys-

tem.

Please retain this manual for future reference.

Before Using Your New Speakers

• The speaker cabinets are made out of wood

and are therefore sensitive to extreme tem-

peratures and humidity. Do not use them in

locations subject to direct sunlight or in

humid places, such as near an air conditioner,

humidiﬁer, bathroom, or kitchen.

• Place the speakers on sturdy, ﬂat surfaces.

Putting them on uneven or unstable surfaces

where they may fall and cause damage will

affect the sound quality.

• Do not keep water or other liquids close to

the speakers. If a liquid is spilled over them,

the woofer and tweeter inside may be dam-

aged.

• Do not handle the speakers with wet or damp

hands.

In catalogs and on packaging, the letter at the end of

the product name indicates the color. Speciﬁcations

and operation are the same regardless of the color.

The speakers can handle the speciﬁed input power

when used for normal music reproduction. If they’re

fed any of the following signals, even if the input

power is within the speciﬁed rating, excessive cur-

rent may ﬂow in the speaker coils, causing burning

or wire breakage:

1. Interstation noise from an untuned FM radio.

2. Audio from a cassette that’s being fast-forwarded.

3. High-pitched sounds generated by an oscillator,

electronic musical instrument, and so on.

4. Ampliﬁer oscillation.

5. Special test tones from audio test CDs and so on.

6. Thumps and clicks caused by connecting or dis-

connecting audio cables (always turn off your

ampliﬁer before connecting or disconnecting

cables).

7. Microphone feedback.

The speakers contain powerful magnets. Do not put

metal items, such as screwdrivers, close to the speak-

ers, as they may be attracted toward the magnet,

causing injury, or damage to the tweeter diaphragm.

Precautions

• D-525/D-425/D-325

The two speakers are identical, so it doesn’t matter

which one you use on the left or right.

TVs and computer monitors are magnetically sensitive

devices and as such are likely to suffer from discolora-

tion or picture distortion when conventional speakers

are placed nearby. To prevent this, the speakers feature

internal magnetic shielding. In some situations, how-

ever, discoloration may still be an issue. In this case,

turn off your TV or monitor, wait 15 to 30 minutes, and

then turn it back on again. This normally activates the

degaussing function, which neutralizes the magnetic

ﬁeld, thereby removing any discoloration effects. If dis-

coloration problems persist, try moving the speakers

away from your TV or monitor. Note that discoloration

can also be caused by a magnet or demagnetizing tool

that’s too close to your TV or monitor.

Note:

If the speakers are placed close to a TV or monitor, due

to the electromagnetic waves radiated by the TV or

monitor, you may hear noise from the speakers even

after your ampliﬁer has been turned off. To prevent this,

position the speakers away from your TV or monitor.

You can use the speakers either with or without their

grilles, which can be removed as follows.

1. Use both hands to gently pull the bottom of the grille

away from the speaker.

2. Use both hands to gently pull the top of the grille

away from the speaker.

3. To replace the grille, align the four fasteners and gen-

tly push the grille toward the speaker.

You can improve the sound quality by attaching the

included cork spacers to raise the speakers off the surface

and reduce the contact area. The cork spacers also make

the speakers stable and prevent them from slipping.

• Before connecting the speakers, disconnect your

ampliﬁer’s power cord from the wall outlet and set its

volume control to minimum.

• The speaker’s rated impedance is 4

Ω. Make sure you con-

nect an ampliﬁer that is compatible with a 4

Ω impedance.

• Use the supplied speaker cables to connect the speak-

ers to your ampliﬁer as shown.

D-525/D-425

Getting to Know the Speakers

Using Close to a TV or Computer

Removing the Speaker Grilles

Tweeter Grille

Woofer Cabinet

Grille attach-

ment catcher

ReplaceRemove

Using the Included Cork Spacers

Connecting the Speakers

D-525/D-425 D-325

Cork spacer

Bottom

Right speaker Left speaker

Speaker cable

Positive (+) side is

indicated by a

red line

1.Peel the

insulation off

the ends of

the speaker

cable and

twist the

core wires.

2.Loosen the

terminal screw

and insert the

speaker cable

into the hole

(until the core

wires are

inserted fully).

3.Fasten the

terminal

screw.

D-325

The type of speaker terminals used on the receiver and

their position depends on the model. Refer to the

receiver’s instruction manual for details on connecting

speakers to the receiver.

Before Turning on Your Receiver:

• Make sure the speaker’s positive (+) terminals are

connected to the ampliﬁer’s positive (+) terminals,

and the speaker’s negative (–) terminals are connected

to the ampliﬁer’s negative (–) terminals. If you get the

polarity reversed, the sound will be unnatural, with a

limited bass range and poor stereo image.

• Make sure that the positive (+) and negative (–) wires

are not touching each other. If they are, a short circuit

may occur, damaging your ampliﬁer.

The sound quality of the speakers is directly affected by

the size and shape of the room they’re used in and its

furnishings. When considering where to place your

speakers, read the following:

• Where possible, mount the speakers on speaker

stands, concrete blocks, bricks, or a sturdy bookshelf.

Putting them directly on the ﬂoor will emphasize bass

sounds, creating a boomy sound.

• If a speaker is placed on an uneven surface where it

can wobble or vibrate, bass performance will be

adversely affected. You can eliminate speaker wobble

by putting a shim made out of cork or metal, such as a

coin, underneath the speaker or stand, as shown.

• If you mount the speakers on a ﬂat surface, such as a

bookshelf, you can improve the sound quality by

inserting cork spacers or coins in between the speaker

and the shelf. Raising them off the surface like this

will reduce the contact area and improve the sound.

• If you like lots of bass, mount the speakers on low

speaker stands and place them in front of a solid wall.

• Walls and furnishings affect sound quality. To achieve

a good stereo sound, put the left and right speakers in

similar locations at the same distance away from your

listening position and at the same height. If you put

them in totally different locations, for example, one

on the ﬂoor and the other on a bookshelf, the stereo

imaging will be adversely affected.

• To determine the best positions for your speakers,

imagine an equilateral triangle and put the left and

right speakers at the ends of the base. The ideal listen-

ing position is at or slightly behind the triangle’s apex.

Angle the speakers toward your listening position.

• Glass doors and smooth walls behind the listening

position can reﬂect the sound from the speakers and

can make sounds at certain frequencies louder. You

can prevent this by hanging sound-absorbing mate-

rial, such as thick curtain, on the door or wall.

To maintain the appearance of the speakers, you should

periodically wipe them with a soft, dry cloth. Stubborn

stains can be removed by using a soft cloth dampened

with water and a mild detergent. Dry the speakers

immediately afterward with a clean, dry cloth. Do not

use abrasive cloths, thinners, alcohol, or other chemical

solvents that may damage the ﬁnish.

Right speaker Left speaker

Speaker cable

Positive (+) side is

indicated by a

red line

1. Peel the insulation off the ends

of the speaker cable and twist

the core wires.

2. While pressing the lever, insert

the wire into the hole, and then

release the lever.

3. Make sure that the terminals are

gripping the bare wires, not the

insulation.

Speaker Placement

Care

Shim

Product specificaties

Merk:	Onkyo
Categorie:	Speaker
Model:	ONKD525B
Kleur van het product:	Zwart
Gewicht:	3900 g
Snoerlengte:	1.8 m
Soort:	Inbouwluidsprekers
Gemiddeld vermogen:	- W
Luidsprekers:	2-weg
Audio-uitgangskanalen:	2.0 kanalen
Peak Music Power Output (PMPO):	70 W
Frequentiebereik:	50 - 100000 Hz
Afmetingen (B x D x H):	160 x 272.5 x 275.5 mm
Diameter woofer:	130 mm
Diameter hogetonenluidspreker:	30 mm
Aantal satellieten:	2
Magnetisch afgeschermd:	Ja