Nxg Onyx NX-C8.2-ENC-X Handleiding

Nxg Speaker Onyx NX-C8.2-ENC-X

Lees hieronder de 📖 handleiding in het Nederlandse voor Nxg Onyx NX-C8.2-ENC-X (2 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 41 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

NX-C8.2-ENC-X 8˝ Two-Way In-Ceiling Enclosed Speaker System

Where To Place Your In-Ceiling Speakers

Placement can make all the difference in how your speakers sound, and how easy they will be to

install. Carefully consider where your speakers should be positioned. For optimum performance,

speakers should be mounted to the left and right of the main listening area and a minimum of 8

to 10 feet apart (See Fig. 2). Avoid mounting speakers in stud cavities containing electrical wiring,

heating ducts, water pipes, etc. Make sure the ceiling materials are sturdy enough to support the

weight of the speakers.

Adjustable Tweeters (Fig. 3)

The tweeter in your NXG speaker may be adjusted, allowing you to tailor the speaker to better fit

the listening area. The overall smoothest response is achieved with the tweeter facing straight out:

however, you may find the sound more pleasing by aiming tweeters toward a particular listening

area. To adjust the tweeter, grasp the outside of the tweeter plate and gently pivot it toward the

listening area.

Speaker Installation In Existing Construction (See Fig. 4 on reverse)

Once you have selected the location for your speakers, you are ready to install them.

You will need the following:

• Stud Finder • Drill & Drill Bits • Wire Cutter/Strippers • Speaker Wire

• Pencil • Masking Tape Phillips Screwdriver • Utility Knife or Drywall Saw •

NXG recommends the use of 16-gauge wire minimum. For wire options consult your retailer or

custom audio contractor.

1. NXG Architectural Speakers are designed to be installed in the ceiling or wall area between studs.

Using a stud finder, make sure you are between two studs. Tape the supplied template to the wall

and lightly trace around the inside with a pencil.

2. Cut the hole using your drywall saw. You may want to start with a small hole in the center of the

outline. This will allow you to check for any obstructions that may exist behind the desired location.

CAUTION: Be certain electrical wiring, water pipes or heating ducts do not interfere in the planned

installation areas prior to drilling or cutting the wall.

3. Run speaker wire from your amplifier or speaker switching device to the speaker location.

4. Carefully remove the grille and inner grille backing. (Note: The open cell foam inner grille backing

is designed to hide speaker components from view and may be removed if desired.) If you like the

standard white finish of your NXG speakers, skip to step 5, but if if you want your speakers to blend

in with a colored wall or ceiling, now is the time to paint your speaker’s outer frame and perforated

grille. (Remove the foam inner grille backing and put it aside in a clean and dust free area for later

reinstallation if desired.) The speaker’s outer surface will accept ordinary latex wall paint or aerosol

spray paint. Because the speaker baffle surface behind the grille should remain unpainted, you will

need to cover this area with the supplied cardboard paint mask. Cover the speaker’s interior black

surface, woofer and tweeter. Paint the outer speaker frame and grille separately. (Grille painting hint:

Use a paint roller that is nearly out of paint to first paint the inside of the grille, then the outside. This

will avoid paint filling the grille perforations.)

Congratulations on choosing NXG In-Ceiling

Loudspeakers. Like all NXG products, great

care has been taken in their design. Their

combination of advanced engineering and

state-of-the-art materials will provide you with

years of listening pleasure, while blending

smoothly into your home’s decor. Before you

get started, it is a good idea to identify all the

parts and hardware (See Fig. 1).

FIG. 1

FIG. 2

NXG ceiling speakers can be used as rear

surround channels by mounting them

(1) on each side of, (2) just behind, or

(3) in back of the viewing position.

FIG. 3

OWNER’S MANUAL

(Continued on reverse)

Speaker with self-contained

mounting clamps

Metal grille with foam

inner grille cover

Black

grille

adhesive

Cutout

template

Painting mask

Pivoting

tweeter

Grille

removal

tool

Warranty Service

Warranty service must be performed by an authorized service center, usually a NXG speaker

systems dealer or its authorized agent. You may obtain a list

of authorized service centers by contacting NXG. All war-

ranty repairs must be accompanied by the original bill of

sales. No other document is acceptable or is required. This

warranty gives you specific legal rights, and you may also

have other rights which vary from state to state.

NXG reserves the right to revise speaker system specifications

without notice.

NXG Speakers Three-Year Limited Warranty

If the NXG speaker system proves to be defective in workmanship or materials within three

years from the date of the original customer’s purchase, we will, at our option, repair or

replace the defective product.

Limitation of Implied Warranties

Any implied warranties, including warranties of merchantability and fitness for a particular

purpose, are limited in duration to the length of this warranty.

Exclusion of Certain Damages

NXG’s liability for any defective product is limited to repair or replacement of the product at

our option.NXG shall not be liable for incidental or consequential damages of any kind or

character because of product defects. Some states do not allow limitations on how long an

implied warranty lasts and/or do not allow the exclusion or limitation of incidental or conse-

quential damages, so the above limitations and exclusions may not apply.

5. Attach the wire to the input terminals on the rear of the

speaker. Remember to maintain proper polarity with the

amplifier by attaching the positive (+) lead to the red ter-

minal and the negative (-) lead to the black terminal.

6. See Fig. 5. With the speaker wire attached to the

speaker, slide the speaker up inside the cut-out hole.

Center the speaker in the cut-out hole and turn the four

locking screws clockwise until the speaker is drawn up

snugly to the wall board from behind, clamping the speak-

er in place. Try to tighten each screw equally. Replace the

speaker grill by gently pressing it into place. If necessary,

use black grille adhesive to secure the grille.

New Construction

1. Determine speaker locations and mark them on your

plans for future reference.

2. If possible, run speaker wires after HVACand electrical

wiring is in place.

3. Secure speaker wires in place along the run with insu-

lated staples only and be careful not to pierce the wire’s

insulation. Allow a bit of slack for expansion of building

materials.

4. Needless to say, the actual speakers should not be

installed until the wall board is in place. In the meantime,

leave several feet of wire coiled up and secured at the

back side of the mounting hole.

5. To complete the installation follow steps 2 through 5

above.

Operational Check

After making all connections it’s a good idea to make sure

every thing is working properly. Turn on your surround or

stereo system making sure the volume control is turned

down and that the balance control is in the center position.

Activate a musical or movie source such as FM, a CD or

DVD player. Gently turn up the volume, you should hear

sound coming from your new NXG speakers. If no sound

is heard from any or all speakers, switch off the system

immediately and check for open or loose connections,

wrong polarity or shorts, or improper source selection.

FIG. 5

16648 North 94th Street

Scottsdale, AZ 85260

1-800-733-0008

www.nxgtech.com

This Warranty Does Not Cover:

• Damage caused by abuse, accident, misuse, negligence, or improper operation.

• Any product whose serial number has been altered, defaced, or removed.

• Products that have been altered or modified.

• Normal wear and maintenance.

• Damages caused by shipping. (All claims for shipping damage must be made with the carrier.)

FIG. 4

(Continued from front)

Input

Connectors

NX-C8.2-ENC-X Specifications

Maximum Power Handling: 5 - 80 watts

Sensitivity: 90dB @ 1 watt/1 meter

Frequency Response: 55 Hz-20,000 Hz

Driver Complement:

8˝ (20 mm) mica-filled polylaminate 3 cone woofer with rubber surround

1/2˝ (13mm) zero-diffraction pivoting, liquid-cooled titanium anodized dome tweeter

Nominal Impedance: 8 ohms

Overall Dimensions: 11˝ (diameter) round x 7˝ D (279mm x 178mm)

Required Ceiling Cutout: 95/8˝ (diameter) round (244mm)

Product specificaties

Merk:	Nxg
Categorie:	Speaker
Model:	Onyx NX-C8.2-ENC-X

Heb je hulp nodig?

Als je hulp nodig hebt met Nxg Onyx NX-C8.2-ENC-X stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Speaker Nxg

Nxg NX-W5.2-LCR-P Handleiding

7 Juli 2023

Nxg NX-W6.2-P Handleiding

7 Juli 2023

Nxg Onyx NX-C8.2-ENC-X Handleiding

1 Juli 2023

Nxg NX-C8.3-P Handleiding

29 Juni 2023

Nxg NX-C8.2-P Handleiding

28 Juni 2023

Nxg NX-AW5 Handleiding

3 November 2022

Handleiding Speaker

Nieuwste handleidingen voor Speaker

Monitor Audio Apex A10AV12 Handleiding

17 December 2024

Audac ATEO6M Handleiding

17 December 2024

Audac CIRA724I Handleiding

17 December 2024

NGS WILD Space 3 Handleiding

16 December 2024

HK Audio LINEAR 3 112 XA Handleiding

16 December 2024

HK Audio Linear 7 112 FA Handleiding

16 December 2024

Monitor Audio Gold 100 6G Handleiding

16 December 2024

Infinity FPS-1000 Handleiding

16 December 2024

Yamaha VXS8-VA Handleiding

14 December 2024

JBL L1 Handleiding

14 December 2024