Nxg NX-C8.2-P Handleiding

Nxg Speaker NX-C8.2-P

Lees hieronder de 📖 handleiding in het Nederlandse voor Nxg NX-C8.2-P (2 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 60 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

(Continued on reverse)

Where To Place Your In-Ceiling Speakers (Fig. 2)

Placement can make all the difference in how your speakers sound, and how easy they will be to install.

Carefully consider where your speakers should be positioned. For optimum performance, speakers should be

mounted to the left and right of the main listening area and a minimum of 8 to 10 feet apart. Avoid mounting

speakers in stud cavities containing electrical wiring, heating ducts, water pipes, etc. Make sure the ceiling

materials are sturdy enough to support the weight of the speakers. Optimum performance will be achieved

when your speakers are mounted to the left and right of the main listening area.

Pivoting Tweeters (Fig. 3)

The tweeters in all NXG Pro Series speakers may be adjusted, allowing you to focus the speakers’ high

frequency output to better fit the listening area. The overall smoothest response is achieved with the tweeter

facing straight out: however, you may find the sound more pleasing by aiming tweeters toward a particular lis-

tening area. To adjust the tweeter, apply pressure on the ring surrounding the tweeter with your thumb or

finger.

Tweeter Level Adjustments (Fig. 4)

The tweeter level control allows you to tailor the speakers’ frequency response to better match the room’s

acoustics. As an example, if a room has a hardwood floor, which makes it acoustically brighter sounding,

you may want to adjust the tweeter level down to compensate. You can experiment to find the sound that’s

most pleasing to you in your particular listening environment.

Speaker Installation In Existing Construction (See Fig. 5 on reverse)

Once you have selected the location for your speakers, you are ready to install them.

You will need the following:

• Stud Finder • Drill & Drill Bits • Wire Cutter/Strippers

• Utility Knife or Drywall Saw • Small LevelPencil •

• Masking Tape • Phillips Screwdriver • Speaker Wire

NXG recommends the use of 16-gauge wire minimum. For wire options consult your retailer or custom

audio contractor.

1. NXG Architectural Speakers are designed to be installed in the cavities between wall studs. Using a stud

finder, make sure you are between two studs. Using the supplied template and a level to ensure your tem-

plate is straight, tape the template to the wall and lightly trace around the outside with a pencil.

2. Cut the hole using your drywall saw. You may want to start with a small hole in the center of the outline.

This will allow you to check for any obstructions that may exist behind the desired location. CAUTION: Be

certain electrical wiring, water pipes or heating ducts do not interfere in the planned installation areas prior

to drilling or cutting the wall.

3. Run speaker wire from your amplifier or speaker switching device to the speaker location.

4. If you like the standard white finish of your NXG speakers, skip to step 5, but if if you want your

speakers to blend in with a colored wall or ceiling, now is the time to paint your speaker’s outer frame and

perforated grille. The speaker’s outer surface will accept ordinary latex wall paint or aerosol spray paint.

Because the speaker baffle surface behind the grille should remain unpainted, you will need to cover this

area with the supplied paint mask. Cover the speaker’s interior black surface, woofer and tweeter. Paint the

outer speaker frame and grille separately. (Grille painting hint: Use a paint roller that is nearly out of paint

to first paint the inside of the grille, then the outside. This will avoid paint filling the grille perforations.)

5. Attach the wire to the input terminals on the rear of the speaker. Remember to maintain proper polarity

with the amplifier by attaching the positive (+) lead to the red terminal and the negative (-) lead to the black

terminal.

Thank you for choosing NXG Pro Series

Loudspeakers. Like all NXG products, great

care has been taken in their design. Their

combination of advanced engineering and

state-of-the-art materials will provide you

with years of listening pleasure, while blend-

ing smoothly into your home’s decor. Before

you get started, it is a good idea to identify

all the parts and hardware (See Fig. 1).

Speaker with self-contained

mounting clamps

Aluminum grille with

foam inner backing

FIG. 2

NXG Pro Series speakers can be used as

rear surround channels by mounting them

(1) on each side of, (2) just behind,

or (3) in back of the viewing position.

FIG. 3

Adjust tweeter level as shown

Press on the edge of

the tweeter to rotate

FIG. 4

NX-C8.2-P 8˝ Two-Way In-Ceiling Speaker System

FIG. 1

Grille

removal

tool

Black

grille

adhesive

Tweeter Level

Switch

Painting masks

Cutout templates

(Continued from front)

6. See Fig. 6. With the speaker wire attached to the speaker, slide

the speaker up inside the cut-out hole. Center the speaker in the

cut-out hole and turn the four locking screws clockwise until the

speaker is drawn up snugly to the wall board from behind, clamping

the speaker in place. Try to tighten each screw equally. Replace the

speaker grill by gently pressing it into place.

New Construction (A)

Note: Use of optional new construction rough-in bracket kits will

not only save time but will also enhance the sound quality of your

installed speakers. (See rough-in kit installation manual for mounting

instructions when using kits.)

New Construction (B)

(Installation without use of new construction rough-in brackets.)

1. Determine speaker locations and mark them on your plans for

future reference.

2. If possible, run speaker wires after HVAC and electrical wiring is

in place.

3. Secure speaker wires in place along the run with insulated staples

only and be careful not to pierce the wire’s insulation. Allow a bit of

slack for expansion of building materials.

4. Needless to say, the actual speakers should not be installed until

the wall board is in place. In the meantime, leave several feet of wire

coiled up and secured at the back side of the mounting hole.

5. To complete the installation follow steps 2 through 5 above.

FIG. 6

16648 North 94th Street • Scottsdale, AZ 85260

1-800-733-0008 www.nxgtech.com

NXG -YPro Series Three ear Limited Warranty

If the NXG Pro Series speaker system proves to be defective in workmanship or materials within

three years from the date of the original customer’s purchase, we will, at our option, repair or

replace the defective product.

Limitation of Implied Warranties

Any implied warranties, including warranties of merchantability and fitness for a particular purpose,

are limited in duration to the length of this warranty.

Exclusion of Certain Damages

NXG’s liability for any defective product is limited to repair or replacement of the product at our

our option. NXG shall not be liable for incidental or consequential damages of any kind or character

because of product defects. Some states do not allow limitations on how long an implied warranty

lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitations and exclusions may not apply.

This Warranty Does Not Cover:

• Damage caused by abuse, accident, misuse, negligence, or improper operation.

• Any product whose serial number has been altered, defaced, or removed.

• Products that have been altered or modified.

• Normal wear and maintenance.

• Damages caused by shipping. (All claims for shipping damage must be made with

the carrier.)

Warranty Service

Warranty service must be performed by an authorized service center, usually an NXG speaker

systems dealer or its authorized agent. You may obtain a list of authorized service centers by con-

tacting NXG. All warranty repairs must be accompanied by the original bill of sales. No other doc-

ument is acceptable or is required. This warranty gives you specific legal rights, and you may also

have other rights which vary from state to state. NXG reserves the right to revise speaker system

specifications without notice.

Operational Check

After making all connections, it’s a good idea to make sure every-

thing is working properly. Turn on your surround or stereo system,

making sure the volume control is turned down and that the balance

control is in the center position. Activate a musical or movie source

such as FM, a CD or DVD player. Gently turn up the volume, you

should hear sound coming from your new NXG speakers. If no

sound is heard from any or all speakers, switch off the system

immediately and check for open or loose connections, wrong polar-

ity or shorts, or proper source selection.

NX-C8.2-P Specifications

Maximum Power Handling: 5 - 120 watts

Sensitivity: 90dB @ 1 watt/1 meter

Frequency Response: 37 Hz-22,000 Hz

Driver Complement:

8˝ (204 mm) metallic-anodized, graphite-filled, injection-molded RCT

cone woofer with rubber surround

1˝ (25mm) minimum diffraction, pivoting, fluid-cooled, high tenacity

teteron dome tweeter

Impedance: 8 ohms nominal, 6 ohms minimum

Grille: Corrosion-resistant powder coated aluminum

Overall Dimensions (Diameter x Depth): 10 3/4˝ x 4˝ D (273 mm x 102 mm)

Required Ceiling Cutout: 91

/2˝ (241 mm) diameter

FIG. 5

Product specificaties

Merk:	Nxg
Categorie:	Speaker
Model:	NX-C8.2-P

Heb je hulp nodig?

Als je hulp nodig hebt met Nxg NX-C8.2-P stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Speaker Nxg

Nxg NX-W5.2-LCR-P Handleiding

7 Juli 2023

Nxg NX-W6.2-P Handleiding

7 Juli 2023

Nxg Onyx NX-C8.2-ENC-X Handleiding

1 Juli 2023

Nxg NX-C8.3-P Handleiding

29 Juni 2023

Nxg NX-C8.2-P Handleiding

28 Juni 2023

Nxg NX-AW5 Handleiding

3 November 2022

Handleiding Speaker

Nieuwste handleidingen voor Speaker

Monitor Audio Apex A10AV12 Handleiding

17 December 2024

Audac ATEO6M Handleiding

17 December 2024

Audac CIRA724I Handleiding

17 December 2024

NGS WILD Space 3 Handleiding

16 December 2024

HK Audio LINEAR 3 112 XA Handleiding

16 December 2024

HK Audio Linear 7 112 FA Handleiding

16 December 2024

Monitor Audio Gold 100 6G Handleiding

16 December 2024

Infinity FPS-1000 Handleiding

16 December 2024

Yamaha VXS8-VA Handleiding

14 December 2024

JBL L1 Handleiding

14 December 2024