Noise Engineering Pura Ruina Handleiding


Lees hieronder de šŸ“– handleiding in het Nederlandse voor Noise Engineering Pura Ruina (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 2 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
Overview
Pura Ruina is a three-stage CV-controlled fully-hyphenated full-wave rectiļ¬er/distortion designed for
audio. Simple waveforms can be manipulated into completely new and exciting tones, and already-
complex sounds can be shredded into sonic oblivion. Add some CV and youā€™ll never want to let PR out
of your rack! Each stage has an individual level control with corresponding CV and individual out, as
well as feeding to the universal Sum output. PRā€™s rectiļ¬cation creates a unique ļ¬‚avor of distortion
unlike standard wavefolding or clipping. The possibilities are virtually endless: add to a west-coast
style complex oscillator setup for unique timbral shaping, annihilate a percussion mix through it, run its
individual outs through other Ruina modules for further mayhemā€¦ Youā€™ll never run out of awesome
things to try, we promise. You know you want one.
1
Noise Engineering
Pura Ruina
Three-stage CV-controlled full-wave rectiļ¬er.
Type
Three-stage rectiļ¬er/folder
Size
8HP Eurorack
Depth
.8 Inches
Power
2x5 Eurorack
+12 mA
75 mA
-12 mA
65 mA
Etymology
Ruina -- from Latin: ā€œdestructionā€
Pura -- from Latin: ā€œpureā€
ā€œPure destructionā€
CV inputs are all 0-5v.
Input & output voltages
Special Thanks
Shawn Jimmerson, as always, has been a guiding light throughout the development of this module.
Power
Screw your module into your case BEFORE powering on the
module. You risk bumping the moduleā€™s PCB against something
metallic and damaging it if itā€™s not properly secured when powered
on.
To power your Noise Engineering module, turn oļ¬€ your case. Plug
one end of your ribbon cable into your power board so that the red
stripe on the ribbon cable is aligned to the side that says -12v and
each pin on the power header is plugged into the connector on the
ribbon. Make sure no pins are overhanging the connector.
Line up the red stripe on the ribbon cable so that it matches the
white stripe and/or -12v indication on the board and plug in the
connector.
You should be good to go if you followed these instructions. Now
go make some noise!
A final note. Some modules have other headers -- they may have a
different number of pins or may say NOT POWER. In general,
unless a manual tells you otherwise, DO NOT CONNECT THOSE
TO POWER.
Warranty
This warranty does not cover damage due to improper handling, storage, use, or abuse, modiļ¬cations, or
improper power or other voltage application.
Noise Engineering backs all our products with a product warranty: we guarantee our products to be free
from manufacturing defects (materials or workmanship) for one year from the date of the original retail
purchase (receipt or invoice required). The cost of shipping to Noise Engineering is paid by the user.
Modules requiring warranty repair will either be repaired or replaced at Noise Engineering's discretion. If
you believe you have a product that has a defect that is out of warranty, please contact us.
2
Interface
1:
Output for all four stages summed together.
Single full-wave rectiļ¬cation stage volume.
Dry signal volume.
All CV:
Double full-wave rectiļ¬cation volume.
8:
In:
Audio input.
See Design Notes (below) for information on full-wave rectiļ¬cation.
Outs 1/2/4/8:
Individual outputs for each section.
2:
Simultaneous control of all four CV inputs.
4:
CV control of volume for each stage. Knobs act as oļ¬€sets for the CV inputs.
Sum Out:
Triple full-wave rectiļ¬cation volume.
CV ins 1/2/4/8:
3
8
CV Out
In
Sum
Out
All
CV
4
2
1
1
Pura Ruina
4
2
8
Patch Tutorial
PR can act as a complex VCA. Run an oscillator to the In jack and the Out jack to
your mixer. Run an envelope to the All CV input. PR now controls the volume of
your voice as well as adding harmonic complexity! For even more control, run
the envelope through a mult and attenuators (like Sinc Defero) and modulate each
sectionā€™s volume individually for more harmonic possibilities.
Second Patch:
Patch a simple waveform (like a sine wave) to the In jack. Patch the Sum Out
jack to your mixer. Adjust the knobs to see what kind of sounds PR can create.
Using the patch from the previous example, take a quad CV source like Mimetic
Digitalis and modulate the 1, 2, 4, and 8 CV inputs to create tonally evolving
sequences.
Fourth Patch:
First Patch:
Third Patch:
Patch a diļ¬€erent type of sound (for instance, a percussive loop) and run it through
PR. New sounds are waiting to be discovered!


Product specificaties

Merk: Noise Engineering
Categorie: Niet gecategoriseerd
Model: Pura Ruina

Heb je hulp nodig?

Als je hulp nodig hebt met Noise Engineering Pura Ruina stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Noise Engineering

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd