Nexxt ARNPR3G5U1 Handleiding

Nexxt Router ARNPR3G5U1

Lees hieronder de 📖 handleiding in het Nederlandse voor Nexxt ARNPR3G5U1 (2 pagina's) in de categorie Router. Deze handleiding was nuttig voor 62 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Power button

Micro SD Card slot

Micro USB port

WPS button

Quick Installation Guide

1 2 3

Thank you for purchasing the new mobile hotspot

from Nexxt Solutions™. If any of the following items

are mismatched, missing or damaged, please contact

the merchant from whom you purchased the unit for

immediate replacement.

• 3G mobile hotspot

• Rechargeable 2000mAh battery

• Micro USB to USB charging cable

• Quick installation guide

• A compatible SIM card with mobile data service

• A computer with Windows®, Macintosh®,

or Linux-based operating system

• Internet Explorer 7, Firefox 12.0, Chrome 20.0,

or Safari

Locate the small groove on the top of the hotspot.

Gently pry open the back cover in order to remove it.

This device belongs to the new generation of portable

SIM based Wi-Fi hotspots. This device comes with a

built-in 3G modem and a 2000mAh battery making it

a true mobile solution. The rechargeable battery works

up to 6 hours or 72 hours in standby mode.

The hotspot operates under the HSPA+ protocol,

supporting download speeds of 21.6Mbps with up to

8 simultaneous users.

4 5 6

7 8

10 11 12

You must fully charge the battery prior to using the

hotspot for the first time.

Firmly insert the micro-USB end of the supplied charger

cable into the I/O port on the hotspot, and the other

end to an AC power adapter (faster way to charge),

power bank or to an available USB port on your

computer.

The new battery needs to be initially charged for at

least 5 hours.

Let the battery drain completely, before recharging it to

full capacity once again. Thereafter, allow the battery to

charge until the indicator meter on the screen is full.

The device can be used while it is charging.

Button

Press this button for 1 to 3 seconds to add new

wireless devices quickly and easily using Wi-Fi

Protected Setup (WPS)

Press this button for about 7 seconds to turn the

wireless feature on and off

Press this button for 1 to 2 seconds to turn the

OLED screen on and off

Press this button for 7 seconds to turn your device

on and off

Press this button with a needle or a sharp pointed tool

for 4 to 5 seconds to initialize the device

The device supports memory cards with a maximum

capacity of 32GB. Insert a user-supplied micro-SD

card in this slot, if desired

Description

WPS

button

Power

button

Micro SD

card slot

Use the included cable to connect to a powered USB

port to charge the device, or to access the

configuration utility.

Micro USB

connector

Reset

button

Function

The number of bars displayed reflects the signal

strength of your network. More bars indicate a

stronger signal. No bars represent no connection

to the network

H+: Currently connected to a HSPA+ mobile network

H: Currently connected to a HSPA mobile network

3G: Currently connected to a WCDMA mobile network

2G: Currently connected to a GPRS/EDGE network

: No network is active. When no SIM card is

detected by the device, the icon will also be

displayed on the screen

The icon indicates that your Wi-Fi network is

currently turned on

The number displayed next to this icon indicates how

many clients are currently using the Wi-Fi signal.

The device allows a maximum of 8 users to be

connected simultaneously to the network

Description

Signal

strength

Network

type

Wi-Fi and

clients

System requirements

Preliminary steps

Introduction

Before using your hotspot for the first time, you must

insert a SIM card. You need to have one available in

order to operate on a GSM network, known as Global

System for Mobile Communication. The installation

process is as follows:

Basic setup

Installing the battery, SD memory and SIM card

Charging your mobile device

This convenient OLED screen provides key information

about your device, such as network activity, signal

strength, current battery level and connection status,

all done in real time.

2. OLED screen

Side and back viewsFront view

Product layout

•

This section describes the functions of the controls and

buttons, as well as the icons and parameters displayed

on the OLED screen.

Device operation

1. Hardware components

1. OLED screen

2. WPS button

3. Power button

4. Reset button

5. Battery compartment

6. Micro-USB charging port

7. Groove

8. Micro SD card slot

1. Now, proceed with the battery installation by aligning

the contacts on the unit with the connectors inside

the compartment.

Slide the micro-SD card (if you have one available) in

the corresponding memory slot located on the side,

as marked, also making sure the contacts of the

card are facing down.

Replace the hotspot cover by carefully pressing it

down until it locks in place.

Slide the SIM card in the slot inside the compartment,

as marked, making sure the contacts of the card are

facing down.

Function

This icon is displayed when there is an active

internet connection

When the envelope icon is displayed, it means that

there are unread messages in the inbox. The number

indicates how many unread messages are currently

stored in this folder

This icon displays the amount of energy stored in the

battery. While charging, the animated icon and the

current battery level will be shown on the screen

Description

Internet

connection

status

SMS

Battery

status

Wi-Fi Protected Setup. When is displayed, WPS

it means that the device is ready for WPS association

with wireless clients

WPS

123

9 108

456

Function Description

: Auto mode. The device is set to connect to the

mobile network automatically

: Manual mode. The device is set to connect to

the mobile network manually

: On demand mode. The device will connect to

the preferred mobile network when Internet access

is required

Connection

method

The name of the mobile network operator to which

the device is currently connected

Operator

The device is currently roaming on a network other

than the home network

Roaming

Quick Installation Guide

13 14

16 17

19 20

Installation

Initial configuration

Connect your device via Wi-Fi

Our hotspot can be accessed using a wireless connec-

tion from anywhere within the operating range of its

wireless network. Keep in mind that the quantity,

thickness and location of walls, ceilings, or other objects

After charging your device and installing a SIM card, you

can connect it via Wi-Fi, as described below:

Note: The following example uses Windows 7 built-in

wireless connection utility. The process may differ if you

are using a different operating system, or a third party

connection utility.

Note: Obtain an IP If your computer is not set to

address automatically Obtain DNS server address and

automatically, you will need to execute these three

initial steps. Otherwise, you may skip to step 4 of the

configuration process.

Press the power button on the side panel to switch

the hotspot on.

Nexxt Solutions will be displayed on the screen as

the router performs its initialization process.

After a few moments, the OLED display will show the

current status of the router. For more details on the

OLED display functions, please refer to the table on

the previous section.

Go back to the page, and select Connection Operation

the item you just configured in the previous step. Click

on and to move on to the next step. Set Connect

When the link status of the device appears as

Connected, it means that internet access is enabled.

At this stage, the user can click on the tab. Home

This main page provides a summary of the current

status of your network, configuration settings, traffic

statistics, as well as all relevant information pertaining

to the device system. In addition, this page also gives

the user access to the more advanced settings, such

as WAN, Network, SMS, Wi-Fi, etc, if he later decides

to customize any special features on the device.

Select > > , click WAN Connection User Profile Add

to configure the , , , , Name APN Protocol User

password (If you cannot locate this information,

contact your service provider). Then click OK

followed by .Apply

After successfully logging in, configure the router

according to the mode selected. In this case, the

Manual mode is used to illustrate the process.

22 23

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful

interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

FCC Statement

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and

receiver.

Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV

technician for help.

•

interference will not occur in a particular installation.

If this equipment does cause harmful interference to

radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged

to try to correct the interference by one of the following

measures:

FCC ID: X4YTRNTY3G

that the wireless signals must pass through may

adversely affect wireless signals.

Go to Start →Control Panel →Network and Internet

→ → Network and Sharing Center Change adapter

settings Wireless Network Connection. Right click on ,

and select .Properties

On the item list, click on Internet Protocol Version

( ).TCP/IPv4

Check both options: Obtain an IP address automatically

and . Obtain DNS server address automatically

Click to finish and exit the PC configuration.OK

Click on the wireless connection icon in the lower right

corner of the computer’s desktop. When done, proceed

to click on the refresh button, followed by the selection

of the default SSID of the router. Finish by checking the

Connect automatically box in order to enable the

selected link.

Click on the button. When the Connect Connected

message appears on the screen, it means that you have

successfully connected to your wireless router.

Web browser configuration

By default, the hotspot is set to match your SIM card

settings automatically to gain Internet access.

Should the automatic mode fail, and no icon appears

on the screen, the user will need to execute the manual

procedure described below:

Note:

The default SSID of the network is Nexxt_XXXXXX

(whereby XXXXXX represent the last unique six charac-

ters of each router's MAC address). No default wireless

password is required at this point.

Open a web browser and enter on 192.168.0.1

the address field, and press enter. When prompted,

enter as the default user name and password, admin

both in lower case. Click to continue.Login

Product specificaties

Merk:	Nexxt
Categorie:	Router
Model:	ARNPR3G5U1
Kleur van het product:	Zwart
Breedte:	100 mm
Diepte:	50 mm
Hoogte:	16 mm
Materiaal behuizing:	Acrylonitrile butadiene styrene (ABS), Plastic
Capaciteit van de accu/batterij:	2000 mAh
Aan/uitschakelaar:	Ja
Maximale capaciteit van de geheugenkaart:	32 GB
2G standaarden:	EDGE, GPRS, GSM
3G standaarden:	HSPA, HSPA+, UMTS, WCDMA
Wi-Fi-standaarden:	802.11b, 802.11g, Wi-Fi 4 (802.11n)
Generatie mobiel internet:	3G
USB-poort:	Ja
Ethernet LAN:	Nee
Type stroombron:	Batterij/Accu
Compatibele geheugenkaarten:	MicroSD (TransFlash)
SMS:	Ja
Markt positionering:	Draagbaar
Certificering:	FCC
Levensduur accu/batterij:	6 uur
SIM-kaartsleuf:	Ja
3G/4G USB modem compatibiliteit:	Ja
Geheugenkaart slot(s):	Ja
Wifi-band:	Single-band (2.4 GHz)
Wifi-standaard:	Wi-Fi 4 (802.11n)
WLAN gegevensoverdrachtsnelheid (max):	21.6 Mbit/s
WLAN gegevensoverdrachtsnelheid (eerste band):	21.6 Mbit/s
Interfacetype Ethernet LAN:	Niet beschikbaar
Netwerkstandaard:	IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.3, IEEE 802.3u, IEEE 802.3x
Ondersteunde beveiligingsalgoritmen:	WEP, WPA, WPA-PSK, WPA2, WPA2-PSK, WPS
Soort antenne:	Intern
Antennas quantity:	2
Antenne versterkingsniveau (max):	3 dBi
3G:	Ja
Soort apparaat:	Draadloze netwerkapparatuur voor mobiele telefonie
Temperatuur bij opslag:	-20 - 60 °C
Luchtvochtigheid bij opslag:	5 - 90 procent
UMTS bands ondersteund:	850,1900,2100 MHz
GSM bands ondersteund:	850,900,1800,1900 MHz
Reset button:	Ja
USB oplaadpoort:	Ja
MAC adres filtering:	Ja
Filtratie:	Ja
Ethernet WAN:	Nee
Firewall:	Ja
DHCP server:	Ja
DHCP client:	Ja
DSL WAN:	Nee
WPS Push Button Security:	Ja
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Type product:	Draagbare router
Antenne-ontwerp:	Intern