Nexa AN-196 Handleiding

Nexa Receiver AN-196

Lees hieronder de 📖 handleiding in het Nederlandse voor Nexa AN-196 (5 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/5

AN-196

Inbyggnadsmottagare

På/Av, 2 kanaler

TEKNISK DATA

AN-179

Strömkälla 220-240 V~50 Hz

Max. last 2 x 1000 W R

Frekvens Z-Wave (868,42 MHz)

Räckvidd upp till 30 m

Strömförbrukning < 1 W (standby)

IP klassicering Inomhusbruk

Mått (B x H x D) 43 x 42 x 16 mm

Inbyggnadsmottagare för fast installation. Liten och kompakt

storlek för placering i kopplings- eller apparatdosa. Kan anslutas

till beﬁntlig strömbrytare. Mottagaren behöver både fas och nolla.

Mottagaren har full kompatibilitet med Z-Wave Plus standarden.

SÄKERHET

Läs igenom hela instruktionen först. Anlita fackman vid behov. Nexa

kan ej hållas ansvarig om produkten används till annat än den är

designad för eller om instruktionen inte följs.

Anslut aldrig lampor eller utrustning som överskrider mottagarens

maximala angivna belastning, det kan leda till fel, kortslutning eller

brand.

Försök inte att reparera produkten. Produkten innehåller inga

reparerbara delar.

INSTALLATION

Säkerställ att ledarna är spänningsfria genom att slå av

strömmen i elcentralen.

Koppla Fas till L, Last/Tändtråd till LS1/LS2 och Nolledare till N.

AN-196 kan kopplas till strömbrytare, även återfjädrande, för

styrning, se även kopplingsschema.

Observera att strömbrytare anslutna till AN-196 måste vara

potentialfria, dvs. helt isolerade från 230V.

ANSLUT TILL ETT Z-WAVE NÄTVERK

Smart start / Autoinklusion:

AN-196 har stöd för SmartStart-funktion, inklusion startar

automatiskt när enheten spänningssätts och upprepas med

dynamiska intervall så länge enheten inte ingår i ett Z-Wave-nätverk.

Z-Wave SmartStart är baserat på Z-Wave SDK 6.8x och kräver att

controller har stöd för detta.

Om controller inte stöder SmartStart-funktion kan den här enheten

läggas till Z-Wave-nätverket med manuell inklusion, eller genom att

skanna DSK QR-koden eller ange en 5-siffrig ”Device Speciﬁc Key”

(DSK) på begäran av gatewayen.

1. Sätt Z-Wave controllern i inklusionsläge (se controllerns manual)

2. Anslut AN-196 till spänning och enheten inkluderas.

Manuell Inklusion:

1. Sätt Z-Wave controllern i inklusionsläge (se controllerns manual)

2. Tryck 3 ggr på Länkknappen inom 1,5 sekunder

Exklusion:

1. Sätt Z-Wave controllern i exklusionsläge (se controllerns manual)

2. Tryck 3 ggr på Länkknappen inom 1,5 sekunder.

Fabriksåterställning:

1. Tryck 3 ggr på Länkknappen inom 1,5 sekunder.

2. Inom 1 sekund från steg 1 ovan, tryck och håll inne länkknappen

till LED slocknar, ca 5 sekunder.

3. Node ID är raderat och enheten fabriksåterställd.

ANVÄNDNING

Utgångarna på AN-196 kan styras trådlöst med Z-Wave controller

och med anslutna strömbrytare

Se manualen till din Z-Wave controller för mer information.

SVENSKA

SÄKERHET OCH INFORMATION

Räckvidd inomhus: upp till 30 m (optimala förhållanden).

Räckvidden är starkt beroende av lokala förhållanden, till

exempel om det ﬁnns metaller i närheten. Exempelvis har

den tunna metallbeläggning i energiglas med låg emissivitet

negativ inverkan på radiosignalernas räckvidd. Det kan ﬁnnas

begränsningar för användningen av enheten utanför EU. Om

tillämpligt bör du kontrollera att enheten överensstämmer med

lokala föreskrifter.

Max belastning: Anslut aldrig lampor eller utrustning som

överskrider mottagarens maximala belastning. Det kan leda till

fel, kortslutning eller brand.

Livsuppehållande utrustning: Använd aldrig Nexas produkter

till livsuppehållande utrustning eller andra apparater där fel eller

störningar kan få livshotande följder.

Störningar: Alla trådlösa enheter kan drabbas av störningar som

kan påverka prestandan och räckvidden. Det minsta avståndet

mellan två mottagare bör därför vara åtminstone 50 cm

Reparation: Försök inte att reparera produkten. Den innehåller

inga reparerbara delar.

Vattentäthet: Produkten är inte vattentät. Se till att den alltid är

torr. Fukt gör att elektroniken inuti fräts sönder och kan leda till

kortslutning, fel och risk för elstötar.

Rengöring: Rengör produkten med en torr trasa. Använd inte

kemikalier, lösningsmedel eller starka rengöringsmedel.

Miljö: Utsätt inte produkten för stark värme eller kyla, eftersom

det kan skada eller förkorta de elektroniska kretsarnas livslängd.

NEXA AB, DATAVÄGEN 37B, 436 32 ASKIM, SWEDEN

info@nexa.se | www.nexa.se

KOPPLINGSSCHEMA

LAST MAX EFFEKT

Glödlampor & Resistiv last (230V) 1000W /220-240V

Halogenlampor (230V) 450W / 220-240V

LED- & lågenergilampor (230V)

130W / 220-240V (40W x 3)

Z-WAVE PLUS INFO (Root/Endpoint1/Endpoint2)

NOTIFICATION

AGI (ASSOCIATION GROUP INFORMATION) TABLE

VERSION

BASIC COMMANDS

MANUFACTURER

Role Type Node Typer Installer Icon User Icon

Slave Always On Z-Wave Plus

node

On/Off Power

Switch

On/Off Power Switch

Wall outlet

Event Type Event Event Parameters

Length

Power applied for rst time 0x08 0x01 0x00

Group Proﬁle Command Class & Command

(List) N bytes Group Name (UTF-8)

1 General:NA

Binary Switch Report,

Notiﬁcation Report,

Device Reset Locally Notiﬁcation

Lifeline

2 Control Basic Set On/Off control

Button 1

3 Control Basic Set On/Off control

Button 2

Protocol Library 3 (Slave_Enhance_232_Library

Protocol Version 6.04 (6.81.03)

Command Description

Basic Get Inquire about the status of the device

Basic Report Report the status of the device.

Basic Set Set the status of the device.(Value=0XFF (ON), 0x00 (OFF))

Manufacturer ID Product Type Product ID

0x0060 0x0004 0x000E

PROGRAMMING

Z-WAVE GROUP SUPPORT

AN-196 relay module supports three Z-wave Association Groups:

Group 1: Association with 5 Controller nodes.

Group 2: Association with 5 nodes.

Group 3: Association with 5 nodes.

Group 1 commands:

• When the unit is powered up for ﬁrst time, a Notiﬁcation Report

will be sent to the node of Group 1.

• When performing Factory Reset, a Device Reset Locally Notiﬁ-

cation will be sent to the node of Group 1.

• When relay is activated through the switch, the unit will send a

Binary Switch Report to the node of Group 1.

Group 2 commands:

• When switch 1 is pressed, a BASIC SET command containing

a value will be sent to the node of Group 2 (When relay is off,

Basic Set Value=0x00, when relay is on, Basic Set Value=0xFF).

Group 3 commands:

• When switch 2 is pressed, a BASIC SET command containing

a value will be sent to the node of Group 3 (When relay is off,

Basic Set Value=0x00, when relay is on, Basic Set Value=0xFF). COMMAND CLASSES

The module supports Command Classes including -

• COMMAND_CLASS_ZWAVEPLUS_INFO_V2

• COMMAND_CLASS_ASSOCIATION_V2

• COMMAND_CLASS_ASSOCIATION_GRP_INFO

• COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2

• COMMAND_CLASS_MULTI_CHANNEL

• COMMAND_CLASS_TRANSPORT_SERVICE_V2

• COMMAND_CLASS_VERSION_V2

• COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

• COMMAND_CLASS_DEVICE_RESET_LOCALLY

• COMMAND_CLASS_POWERLEVEL

• COMMAND_CLASS_SECURITY

• COMMAND_CLASS_SECURITY_2

• COMMAND_CLASS_SUPERVISION

• COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4

• COMMAND_CLASS_NOTIFICATION_V4

• COMMAND_CLASS_CONFIGURATION

• COMMAND_CLASS_SWITCH_BINARY

END POINT 1/2

• COMMAND_CLASS_ZWAVEPLUS_INFO_V2

• COMMAND_CLASS_SWITCH_BINARY

• COMMAND_CLASS_ASSOCIATION_V2

• COMMAND_CLASS_ASSOCIATION_GRP_INFO

• COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2

• COMMAND_CLASS_SUPERVISION

ADDITIONAL COMMAND CLASSES SUPPORTED

• Binary Switch: Refer to Basic.

• Multi Channel: To control 2 relay independently.

• Firmware Update: For OTA function.

CONFIGURATION

The conﬁgurable values are as following:

Parameter

Number

Parameter

Function Size Range Default

1 Switch 1 Type 1 0~1 0

(0: Momentary 1: Toggle)

2 Switch 2 Type 1 0~1 0

(0: Momentary 1: Toggle)

3Relay 1 Auto

Off Time 4 0~43200(sec.) 0 (Not auto off)

(Max 12 hours)

4Relay 2 Auto

Off Time 4 0~43200(sec.) 0 (Not auto off)

(Max 12 hours)

Set whether to

remember the

last status of

Relay 1

1 1/0 1:Remember

(0: do not remember)

Set whether to

remember the

last status of

Relay 2

1 1/0 1:Remember

(0: do not remember)

Anslutningar för strömbrytare

Anslutningar för spänning

LED indikering

Länkknapp

AN-196

Built-in receiver

On/Off, 2 channels

TECHNICAL DATA

AN-179

Power source 220-240 V~50 Hz

Max. charge 2 x 1000 W R

Frequency Z-Wave (868.42 MHz)

Range up to 30 m

Power consumption < 1 W (standby)

IP rating Indoor use

Dimensions (W x H x D) 43 x 42 x 16 mm

Built-in receiver for permanent installation. Small, compact size

for placing in a junction box or switchbox. Can be connected to

existing switch. The receiver needs both phase and neutral. The

receiver is fully compatible with the Z-Wave Plus standard.

SAFETY

Read through the entire instruction ﬁrst. Engage a professional if so

required. Nexa cannot be held liable if the product is used for any

purpose other than the one for which it is designed, or if there is

failure to comply with the instruction.

Never connect bulbs or equipment exceeding the receiver’s

maximum stated load – this may lead to faults, short-circuiting or ﬁre.

Do not attempt to repair the product. The product contains no

repairable parts.

INSTALLATION

Make sure that the conductors are powered down by turning

off the power in the distribution box.

Connect Phase to L, Load/Ignition wire to LS1/LS2 and Zero

Conductor to N.

AN-196 can be connected to power switches, even momentary

switches, for control, also see wiring diagram.

Please note that switches connected to AN-196 must be potential

free, i.e. fully insulated from 230 V.

CONNECT TO A Z-WAVE NETWORK

Smart start / Auto-inclusion:

AN-196 has support for the Smart Start functions, inclusion

starts automatically when the unit is powered up and repeats at

a dynamic interval for as long as the unit is not part of a Z-Wave

network. Z-Wave SmartStart is based on Z-Wave SDK 6.8x and

requires the controller to have support for this.

If the controller does not support the SmartStart function, the

unit can be added to the Z-Wave network by manual inclusion, or

by scanning the DSC QR code, or by entering a 5-digit "Device

Speciﬁc Code" (DSC) when requested by the gateway.

1. Put the Z-Wave controller in inclusion mode (see the controller's manual)

2. Connect AN-196 to voltage and the unit is included.

Manual Inclusion:

1. Put the Z-Wave controller in inclusion mode (see the controller's manual)

2. Press 3 times on the Link button within 1.5 seconds

Exclusion:

1. Put the Z-Wave controller in exclusion mode (see the controller's manual)

2. Press 3 times on the Link button within 1.5 seconds.

Restore to factory settings:

1. Press 3 times on the Link button within 1.5 seconds.

2. Within 1 second after step 1 above, press and hold down the link

button until the LED goes out, approx. 5 seconds.

3. Node ID is deleted and the unit restored to factory settings.

USE

The outputs on AN-196 can be wirelessly controlled by a Z-Wave

controller and by connected power switch

Consult the manual for your Z-Wave controller for more information.

SAFETY AND INFORMATION

Range indoors: up to 30 m (optimal conditions). The range is

very dependent on the local conditions, for example, if there

are metals in the vicinity. For example, the thin metal coating in

energy glass with low emissivity has a negative inﬂuence on the

range of the radio signals. There may be restrictions on the use

of the unit outside the EU. If appropriate, you should check that

the unit complies with local regulations.

Max load: Never connect lights or equipment that exceed the

receiver's maximum load. This could lead to faults, short-

circuiting or ﬁre.

Life-support equipment: Never use Nexa's products with life-

support equipment or other devices where faults or interference

could have life-threatening consequences.

Interference: All wireless units can suffer from interference

that can affect the performance and range. For this reason, the

minimum distance between two receivers should be at least 50 cm

Repair: Do not attempt to repair the product. It does not contain

any repairable parts.

Waterprooﬁng: The product is not waterproof. Make sure it is

dry at all times. Damp causes the electronics inside to corrode

and this could lead to short-circuiting, faults and a risk for

electric shocks.

Cleaning: Clean the product with a dry cloth. Do not use

chemicals, solvents or strong cleaning agents.

Environment: Do not expose the product to intense heat or cold,

because it could damage or shorten the service life of the electric circuits.

ENGLISH

NEXA AB, DATAVÄGEN 37B, 436 32 ASKIM, SWEDEN

info@nexa.se | www.nexa.se

WIRING DIAGRAM

LOAD MAX POWER

Incandescent bulbs % Resistive loads (230 V) 1000W /220-240 V

Halogen lights (230 V) 450W / 220-240 V

LED & Low energy bulbs (230 V)

130W / 220-240 V (40 W x 3)

Z-WAVE PLUS INFO (Root/Endpoint1/Endpoint2)

NOTIFICATION

AGI (ASSOCIATION GROUP INFORMATION) TABLE

VERSION

BASIC COMMANDS

MANUFACTURER

Role Type Node Types Installer Icon User Icon

Slave Always On Z-Wave Plus

node

On/Off Power

Switch

On/Off Power Switch

Wall outlet

Events Type Events Event Parameters

Length

Power applied for rst time 0x08 0x01 0x00

Group Proﬁle Command Class & Command

(List) N bytes Group Name (UTF-8)

1 General:NA

Binary Switch Report,

Notiﬁcation Report,

Device Reset Locally Notiﬁcation

Lifeline

2 Control Basic Set On/Off control

Button 1

3 Control Basic Set On/Off control

Button 2

Protocol Library 3 (Slave_Enhance_232_Library

Protocol Version 6.04 (6.81.03)

Command Description

Basic Get Inquire about the status of the device

Basic Report Report the status of the device.

Basic Set Set the status of the device.(Value=0XFF (ON), 0x00 (OFF))

Manufacturer ID Product Type Product ID

0x0060 0x0004 0x000E

PROGRAMMING

Z-WAVE GROUP SUPPORT

AN-196 relay module supports three Z-wave Association Groups:

Group 1: Association with 5 Controller nodes.

Group 2: Association with 5 nodes.

Group 3: Association with 5 nodes.

Group 1 commands:

• When the unit is powered up for ﬁrst time, a Notiﬁcation Report

will be sent to the node of Group 1.

• When performing Factory Reset, a Device Reset Locally Notiﬁ-

cation will be sent to the node of Group 1.

• When relay is activated through the switch, the unit will send a

Binary Switch Report to the node of Group 1.

Group 2 commands:

• When switch 1 is pressed, a BASIC SET command containing

a value will be sent to the node of Group 2 (When relay is off,

Basic Set Value=0x00, when relay is on, Basic Set Value=0xFF).

Group 3 commands:

• When switch 2 is pressed, a BASIC SET command containing

a value will be sent to the node of Group 3 (When relay is off,

Basic Set Value=0x00, when relay is on, Basic Set Value=0xFF). COMMAND CLASSES

The module supports Command Classes including -

• COMMAND_CLASS_ZWAVEPLUS_INFO_V2

• COMMAND_CLASS_ASSOCIATION_V2

• COMMAND_CLASS_ASSOCIATION_GRP_INFO

• COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2

• COMMAND_CLASS_MULTI_CHANNEL

• COMMAND_CLASS_TRANSPORT_SERVICE_V2

• COMMAND_CLASS_VERSION_V2

• COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

• COMMAND_CLASS_DEVICE_RESET_LOCALLY

• COMMAND_CLASS_POWERLEVEL

• COMMAND_CLASS_SECURITY

• COMMAND_CLASS_SECURITY_2

• COMMAND_CLASS_SUPERVISION

• COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4

• COMMAND_CLASS_NOTIFICATION_V4

• COMMAND_CLASS_CONFIGURATION

• COMMAND_CLASS_SWITCH_BINARY

END POINT 1/2

• COMMAND_CLASS_ZWAVEPLUS_INFO_V2

• COMMAND_CLASS_SWITCH_BINARY

• COMMAND_CLASS_ASSOCIATION_V2

• COMMAND_CLASS_ASSOCIATION_GRP_INFO

• COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2

• COMMAND_CLASS_SUPERVISION

ADDITIONAL COMMAND CLASSES SUPPORTED

• Binary Switch: Refer to Basic.

• Multi Channel: To control 2 relay independently.

• Firmware Update: For OTA function.

CONFIGURATION

The conﬁgurable values are as following:

Parameter

Number

Parameter

Function Size Range Default

1 Switch 1 Type 1 0~1 0

(0: Momentary 1: Toggle)

2 Switch 2 Type 1 0~1 0

(0: Momentary 1: Toggle)

3Relay 1 Auto

Off Time 4 0~43200(sec.) 0 (Not auto off)

(Max 12 hours)

4Relay 2 Auto

Off Time 4 0~43200(sec.) 0 (Not auto off)

(Max 12 hours)

Set whether to

remember the

last status of

Relay 1

1 1/0 1:Remember

(0: do not remember)

Set whether to

remember the

last status of

Relay 2

1 1/0 1:Remember

(0: do not remember)

Connections for power switch

Connections for voltage

LED display

Link button

AN-196

Innbyggingsmottaker

På/Av, 2 kanaler

TEKNISKE SPESIFIKASJONER

AN-179

Strømkilde 220–240 V~50 Hz

Maks. belastning 2 x 1000 W R

Frekvens Z-Wave (868,42 MHz)

Rekkevidde opptil 30 m

Strømforbruk < 1 W (ventemodus)

IP-klassisering Innendørs bruk

Mål (B x H x D) 43 x 42 x 16 mm

Innbyggingsmottaker for fast installasjon. Liten og kompakt

størrelse for plassering i koblings- eller apparatboks. Kan kobles til

eksisterende strømbryter. Mottakeren må p3-ha både fase og jording.

Mottakeren er fullstendig kompatibel med Z-Wave Plus-standarden.

SIKKERHET

Les gjennom hele instruksjonen først. Kontakt fagperson ved behov.

Nexa kan ikke holdes ansvarlig hvis produktet brukes til noe annet

enn det er beregnet på eller hvis instruksjonene ikke følges.

Du må aldri koble til lamper eller utstyr som overskrider mottakerens

maksimalt angitte belastning. Det kan føre til feil, kortslutning eller brann.

Ikke gjør forsøk på å reparere produktet. Produktet inneholder ingen

reparerbare deler.

INSTALLASJON

Kontroller at ledningene er spenningsfrie ved å slå av strømmen

i fordelingsboksen.

Koble fase til L, belastning/tenntråd til LS1/LS2 og nulleder til N.

AN-196 kan kobles til strømbryter, også tilbakefjærende, for styring,

se også koblingsskjema.

Vær oppmerksom på at strømbrytere koblet til AN-196 må være

potensialfrie, dvs. helt isolerte fra 230 V.

KOBLE TIL ET Z-WAVE-NETTVERK

Smart start/automatisk inklusjon:

AN-196 har støtte for SmartStart-funksjon – inklusjon starter

automatisk når enheten spenningsettes og gjentas ved dynamiske

intervaller så lenge enheten ikke er inkludert i et Z-Wave-nettverk.

Z-Wave SmartStart er basert på Z-Wave SDK 6.8x, og krever at

styreenheten har støtte for dette.

Hvis styreenheten ikke støtter SmartStart-funksjon, kan denne

enheten legges til Z-Wave-nettverket ved manuell inklusjon, eller

ved å skanne DSK QR-koden eller angi en 5-sifret “Device Speciﬁc

Key” (DSK) på forespørsel fra gatewayen.

1. Sett Z-Wave-styreenheten i inklusjonsmodus (se styreenhetens håndbok)

2. Koble AN-196 til spenning, så inkluderes enheten.

Manuell inklusjon:

1. Sett Z-Wave-styreenheten i inklusjonsmodus (se styreenhetens håndbok)

2. Trykk 3 ganger på koblingsknappen innen 1,5 sekund

Eksklusjon:

1. Sett Z-Wave-styreenheten i eksklusjonsmodus (se styreenhetens håndbok)

2. Trykk 3 ganger på koblingsknappen innen 1,5 sekund.

Tilbakestilling av fabrikkinnstillinger:

1. Trykk 3 ganger på koblingsknappen innen 1,5 sekund.

2. Innen 1 sekund etter trinn 1 over trykker du på og holder inne

koblingsknappen til LED-lampen slås av, ca. 5 sekunder.

3. Node-ID er slettet og enheten tilbakestilt til fabrikkinnstillinger.

BRUK

Utgangene på AN-196 kan styres trådløst med Z-Wave-styreenhet

og tilkoblede strømbrytere

Mer informasjon ﬁnnes i håndboken for Z-Wave-styreenheten.

NORSK

SIKKERHET OG INFORMASJON

Rekkevidde innendørs: opptil 30 m (optimale forhold).

Rekkevidden avhenger i betydelig grad av lokale forhold, som

hvorvidt det ﬁnnes metall i nærheten. Det tynne metallbelegget

i energiglass med lav emissivitet har for eksempel en negativ

virkning på radiosignalenes rekkevidde. Det kan ﬁnnes

begrensninger for bruk av enheten utenfor EU. Om aktuelt, bør

du kontrollere at enheten overholder lokale forskrifter.

Maks. belastning: Koble aldri til lamper eller utstyr som

overskrider mottakerens maksimale belastning. Dette kan føre til

feil, kortslutning eller brann.

Livreddende utstyr: Bruk aldri Nexa-produkter til livreddende

utstyr eller andre apparater der feil eller forstyrrelser kan p3-ha

livstruende følger.

Forstyrrelser: Alle trådløse enheter kan utsettes for forstyrrelser,

som kan påvirke både ytelsen og rekkevidden. Den minste

avstanden mellom to mottakere bør derfor være minst 50 cm.

Reparasjon: Ikke gjør forsøk på å reparere produktet. Produktet

inneholder ingen deler som kan repareres.

Vanntetthet: Produktet er ikke vanntett. Påse at det alltid holdes

tørt. Fuktighet gjør at elektronikken inni enheten ødelegges, og

kan føre til kortslutning, feil og fare for elektrisk støt.

Rengjøring: Rengjør produktet med en tørr klut. Bruk aldri

kjemikalier, løsemidler eller aggressive rengjøringsmidler.

Miljø: Produktet skal ikke utsettes for sterk varme eller kulde, ettersom

dette kan skade eller forkorte de elektroniske kretsenes levetid.

NEXA AB, DATAVÄGEN 37B, 436 32 ASKIM, SWEDEN

info@nexa.se | www.nexa.se

KOBLINGSSKJEMA

BELASTNING MAKS. EFFEKT

Lyspærer og resistiv belastning (230 V) 1000W/220–240 V

Halogenpærer (230 V) 450W/220–240 V

LED- og lavenergipærer (230 V)

130W/220–240 V (40 W x 3)

Tilkoblinger for strømbryter

Tilkoblinger for spenning

LED-indikator

Koblingsknapp

Z-WAVE PLUS INFO (Root/Endpoint1/Endpoint2)

NOTIFICATION

AGI (ASSOCIATION GROUP INFORMATION) TABLE

VERSION

BASIC COMMANDS

MANUFACTURER

Role Type Node Types Installer Icon User Icon

Slave Always On Z-Wave Plus

node

On/Off Power

Switch

On/Off Power Switch

Wall outlet

Events Type Events Event Parameters

Length

Power applied for rst time 0x08 0x01 0x00

Group Proﬁle Command Class & Command

(List) N bytes Group Name (UTF-8)

1 General:NA

Binary Switch Report,

Notiﬁcation Report,

Device Reset Locally Notiﬁcation

Lifeline

2 Control Basic Set On/Off control

Button 1

3 Control Basic Set On/Off control

Button 2

Protocol Library 3 (Slave_Enhance_232_Library

Protocol Version 6.04 (6.81.03)

Command Description

Basic Get Inquire about the status of the device

Basic Report Report the status of the device.

Basic Set Set the status of the device.(Value=0XFF (ON), 0x00 (OFF))

Manufacturer ID Product Type Product ID

0x0060 0x0004 0x000E

PROGRAMMING

Z-WAVE GROUP SUPPORT

AN-196 relay module supports three Z-wave Association Groups:

Group 1: Association with 5 Controller nodes.

Group 2: Association with 5 nodes.

Group 3: Association with 5 nodes.

Group 1 commands:

• When the unit is powered up for ﬁrst time, a Notiﬁcation Report

will be sent to the node of Group 1.

• When performing Factory Reset, a Device Reset Locally Notiﬁ-

cation will be sent to the node of Group 1.

• When relay is activated through the switch, the unit will send a

Binary Switch Report to the node of Group 1.

Group 2 commands:

• When switch 1 is pressed, a BASIC SET command containing

a value will be sent to the node of Group 2 (When relay is off,

Basic Set Value=0x00, when relay is on, Basic Set Value=0xFF).

Group 3 commands:

• When switch 2 is pressed, a BASIC SET command containing

a value will be sent to the node of Group 3 (When relay is off,

Basic Set Value=0x00, when relay is on, Basic Set Value=0xFF). COMMAND CLASSES

The module supports Command Classes including -

• COMMAND_CLASS_ZWAVEPLUS_INFO_V2

• COMMAND_CLASS_ASSOCIATION_V2

• COMMAND_CLASS_ASSOCIATION_GRP_INFO

• COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2

• COMMAND_CLASS_MULTI_CHANNEL

• COMMAND_CLASS_TRANSPORT_SERVICE_V2

• COMMAND_CLASS_VERSION_V2

• COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

• COMMAND_CLASS_DEVICE_RESET_LOCALLY

• COMMAND_CLASS_POWERLEVEL

• COMMAND_CLASS_SECURITY

• COMMAND_CLASS_SECURITY_2

• COMMAND_CLASS_SUPERVISION

• COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4

• COMMAND_CLASS_NOTIFICATION_V4

• COMMAND_CLASS_CONFIGURATION

• COMMAND_CLASS_SWITCH_BINARY

END POINT 1/2

• COMMAND_CLASS_ZWAVEPLUS_INFO_V2

• COMMAND_CLASS_SWITCH_BINARY

• COMMAND_CLASS_ASSOCIATION_V2

• COMMAND_CLASS_ASSOCIATION_GRP_INFO

• COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2

• COMMAND_CLASS_SUPERVISION

ADDITIONAL COMMAND CLASSES SUPPORTED

• Binary Switch: Refer to Basic.

• Multi Channel: To control 2 relay independently.

• Firmware Update: For OTA function.

CONFIGURATION

The conﬁgurable values are as following:

Parameter

Number

Parameter

Function Size Range Default

1 Switch 1 Type 1 0~1 0

(0: Momentary 1: Toggle)

2 Switch 2 Type 1 0~1 0

(0: Momentary 1: Toggle)

3Relay 1 Auto

Off Time 4 0~43200(sec.) 0 (Not auto off)

(Max 12 hours)

4Relay 2 Auto

Off Time 4 0~43200(sec.) 0 (Not auto off)

(Max 12 hours)

Set whether to

remember the

last status of

Relay 1

1 1/0 1:Remember

(0: do not remember)

Set whether to

remember the

last status of

Relay 2

1 1/0 1:Remember

(0: do not remember)

Product specificaties

Merk:	Nexa
Categorie:	Receiver
Model:	AN-196
Kleur van het product:	Wit
Breedte:	43 mm
Diepte:	16 mm
Hoogte:	42 mm
Netbelasting:	1000 W
Connectiviteitstechnologie:	Draadloos
Ingangsspanning:	220 - 240 V
Aantal:	1
Frequentie:	868.42 MHz
Bedrijfstemperatuur (T-T):	-10 - 40 °C
Zendbereik:	0 - 30 m