NetworX NX-584 HOME AUTOMATION MODULE Handleiding

NetworX Beveiliging NX-584 HOME AUTOMATION MODULE

Lees hieronder de 📖 handleiding in het Nederlandse voor NetworX NX-584 HOME AUTOMATION MODULE (12 pagina's) in de categorie Beveiliging. Deze handleiding was nuttig voor 57 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

NX-584 HOME AUTOMATION MODULE

Installation Manual

These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to be

met during installation, operation, and maintenance. If further information is desired or if particular problems arise that are not

covered sufficiently for the purchaser’s purpose, the matter should be referred to GE Interlogix, Gladewater, Texas, USA.

This document contains proprietary information of GE Interlogix, USA and is furnished to its customer solely to assist that

customer in the installation, testing, operations, and/or maintenance of the equipment described. This document shall not be

reproduced in whole or in part nor shall its contents be disclosed to any third party without the written approval of GE Interlogix.

Please refer to the current GE Interlogix product catalog for detailed warranty information.

TABLE OF CONTENTS

I. GENERAL DESCRIPTION .................................................................................................2

II. TERMINALS & PIN-OUT....................................................................................................2

III. ENCLOSURE DIAGRAM....................................................................................................3

IV. WIRING DIAGRAM.............................................................................................................4

V. ENROLLING THE MODULE...............................................................................................4

VI. PROGRAMMING THE MODULE........................................................................................5

VII. PROGRAMMING DATA .....................................................................................................5

VIII. LEDS INDICATORS............................................................................................................6

IX. PROGRAMMING LOCATIONS..........................................................................................7

X. PROGRAMMING WORKSHEETS....................................................................................10

XI. SPECIFICATIONS ............................................................................................................12

NX-584 Home Automation

I. GENERAL DESCRIPTION

The NetworX NX-584 is a low cost add-on module that fits neatly into any NetworX family system

enclosure and provides a standard RS-232 bi-directional DB-9 connector for connection to a home

automation host system. A simple three-wire connection to the main control is all that is required to

fully integrate this card into the system.

The NX-584 has several levels of security that can be programmed in at the time of installation to

allow as much or as little security system information to be passed to the host system. It can also be

set to limit the commands that will be accepted from the host system to prevent unauthorized

attempts to override the security system status.

The unit can be easily configured for communication in an ASCII or Binary protocol. A selectable

baud rate can be set from 600 baud to 76.8k baud with hardware RTS and CTS handshaking. The

ASCII implementation is easy to use and debug with standard programming tools while the Binary

version is a more efficient for method for transferring information between the two systems. The

system integrator can select any number of events or conditions to cause the NX-584 to send the

relevant information to the host without polling. This allows for a faster response to activity than

polling alone can provide.

All security system information can be requested at anytime if enabled to do so by the installer. This

is useful at system initialization and at periodic intervals to keep the two systems in sync without

worrying about missing any transitional event. This information is organized as System, Partition,

Zones and Outputs. System information will contain such information as power status, phone line

condition, module troubles, and other system wide condition. Partition information includes readiness

of all zones assigned, armed state, entry / exit delays, last user number, alarm condition and many

other conditions within a specific partition. Zone information includes faults, alarm memory, bypasses,

troubles, tampers, low batteries, missing and partition assignments. Output messages include

commands that can be passed to or from devices in X-10 compatible format.

II. TERMINALS & PIN-OUT

TERMINAL DESCRIPTIONS

POS Connect to the KP POS terminal of the NX-8

COM

Connect to the KP COM terminal of the NX-8

DATA

Connect to the KP DATA terminal of the NX-8

NX-584 Home Automation 3

DB-9 Pin-out Pin Number Signal

Name Direction

NX------PC Jumper

Number A Position B Position

Cts* → J7 8** 7

Txd → J8 2 3**

Rts* ← J9 8 7**

Rxd ← J10 2** 3

Sig.Gnd. ←→ -- 5

Unused -- -- 1,4,6,9

*Note: Rts and Cts signals are not currently supported

**Note: Default jumper settings

III. ENCLOSURE DIAGRAM

Inside the can, several 2-holed insertion points have been

constructed. This allows for either vertical or horizontal placement of

the modules. Notice that the insertion points have two sizes of

holes -- a larger hole and a smaller hole.

Diagram 1: The black plastic PCB guides are grooved on one edge

where the PC Board will be seated. The end with the half-moon

protrusion fits into the larger hole. The smaller hole is for the screw.

Diagram 2: Place the first black plastic PCB guide in the top insertion

point, grooved edge downward. The half-moon protrusion will be in

the large hole. It does not require force. Insert one of the provided

screws into the smaller hole (from inside the can) to secure it in place.

A screwdriver should reach through the notch that runs the length of

the guide to tighten the screw. The second PCB guide should be

positioned opposite of the first (grooved edge up) and placed in the

lower insertion point, using the same procedures described above.

Once mounted, screw it in securely.

Diagram 3: The PC board should slide freely in the grooves of both

guides.

Product specificaties

Merk:	NetworX
Categorie:	Beveiliging
Model:	NX-584 HOME AUTOMATION MODULE

Heb je hulp nodig?

Als je hulp nodig hebt met NetworX NX-584 HOME AUTOMATION MODULE stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Beveiliging NetworX

NetworX NX-124E Handleiding

4 November 2022

NetworX NX-108E Handleiding

4 November 2022

NetworX NX-4 Handleiding

4 November 2022

NetworX NX-448 Handleiding

4 November 2022

NetworX NP0098.1 Handleiding

4 November 2022

NetworX NX-10 Handleiding

4 November 2022

NetworX NX-6V2 System Keypad Handleiding

4 November 2022

NetworX NX-4SE Handleiding

4 November 2022

NetworX NX-6SE Handleiding

4 November 2022

NetworX NX-7002 HomeText Handleiding

4 November 2022

Handleiding Beveiliging

Nieuwste handleidingen voor Beveiliging

Geemarc SOS-PRO 295 Handleiding

6 Maart 2024

Technaxx TX-106 Handleiding

4 Februari 2024

One2track Safety Angel Handleiding

16 Oktober 2023

Sygonix SY-3851632 Handleiding

16 Oktober 2023

Sygonix 1326052 Handleiding

16 Oktober 2023

Sygonix 43588A WLAN Camera Handleiding

16 Oktober 2023

Sygonix 43176S LAN Camera Handleiding

16 Oktober 2023

Sygonix SY-3181234 Handleiding

16 Oktober 2023

Sygonix Touch IP65 Handleiding

16 Oktober 2023

Sygonix 1882082 Handleiding

16 Oktober 2023