MXR Iso-Brick M238 Handleiding

MXR Niet gecategoriseerd Iso-Brick M238

Lees hieronder de 📖 handleiding in het Nederlandse voor MXR Iso-Brick M238 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

92503018757REVA

M238 ISO-BRICK™ POWER SUPPLY

CONTROLS

RED LED indicates bad input

power connection

WHITE LED indicates good

input power connection

POWER outputs power up

to 10 pedals

BLUE LEDs indicate good

output power connection

VOLTAGE controls set

voltage level of variable

6–15V power outputs

18V @ 2000mA power

input jack

M238 ISO-BRICK

™

POWER SUPPLY

DESCRIPTION

• 10 fully isolated outputs

• Quiet, noise-free operation

• Powers a wide range of pedal

types—digital and analog,

positive and negative ground

• Variable outputs can be used to

emulate drained battery effect

DIRECTIONS

• Connect included AC adapter into

the Iso-Brick Power Supply’s 18V

IN jack.

• Plug the AC adapter into a wall

outlet; the white power LED

will light.

• Connect up to six pedals requir-

ing 9V power to the six 9V OUT

jacks using the included barrel-

to-barrel cables. Be sure pedal’s

mA rating does not exceed

output’s indicated mA rating.

• Connect up to two pedals

requiring 18V power to the two

18V OUT jacks using the

included barrel-to-barrel cables.

Be sure pedal’s mA rating does

not exceed output’s indicated

mA rating.

• Two outputs provide controllable

voltage levels, from 6V to 15V.

Use VOLTAGE controls to adjust.

When using analog pedals requir-

POWER

The Iso-Brick Power Supply

requires an 18V regulated power

supply rated at 2000 mA, with

5.5mm x 2.1mm positive barrel,

negative center plug. The included

power adapter can utilize a wide

range of wall power, from 100–240V

at 47–63Hz. Comes with switchable

US/Japan, UK, EU, and

Australian plugs.

CONNECTION NOTES

• Included cables use industry

standard 5.5mm x 2.1mm posi-

tive barrel, negative center

polarity plugs.

• Each output features a blue LED.

When lit, this LED indicates a

good connection. If short-circuit-

ed or overloaded, this LED will

turn off.

• The Iso-Brick Power Supply has

six 9V outputs: two can handle

450mA, two can handle 300mA,

and two can handle 100mA.

• Two 18V outputs can handle

250mA each.

• Two variable 6V–15V outputs can

handle 250mA each.

DUNLOP MA NUFACTURING, INC.

P.O. BOX 846, BENICIA, CA 94510 U.S.A.

TEL: 1-707-745-2722 FAX: 1-707-745-2658

TROUBLESHOOTING

The power LED fails to light.

• Dead AC outlet. Try plugging into

another outlet, or test the outlet

with another device like a lamp.

• Faulty connection. Double check

plugs to make sure they are

inserted securely.

• Short-circuited output. Discon-

nect the cable from the output

whose blue LED is off. Wait 5 to

10 seconds for the unit to reset,

indicated when the blue LED

comes on.

Power provided to some effects,

but not others.

• Incompatible power plug. Check

that the dimensions and polarity

of the pedals are compatible with

the provided cables.

• Faulty cord. Check by swapping

the power cable with another

known good cable.

• Faulty jack on Iso-Brick Power

Supply. Check by plugging the

power cable into a different

DC jack.

• Faulty jack on the pedal.

Test by running the pedal off

battery power.

ing 9V power, VOLTAGE controls

can be used to reduce power and

emulate the effect a dying battery

has on certain pedals. Note: Not

all analog pedals will operate be-

low 9V. Check with manufacturer

for operable voltage range. If your

pedal is sensitive to input volt-

age level, use a voltmeter to set

output voltage before connect-

ing pedal. Be sure pedal’s mA

rating does not exceed output’s

indicated mA rating.

WARNING: Some pedals may

be damaged if powered using

a voltage that exceeds the level

required by the manufacturer, e.g.

powering a 9V pedal with 15V or

18V. We highly recommend stay-

ing at or below manufacturer’s

state voltage requirement. Dunlop

assumes no responsibility or

liability for equipment damage

caused by misuse of the

Iso-Brick Power Supply.

• All outputs may be used simulta-

neously for a total power output

of 31.8 watts.

• Combining Outputs: Any output

may be combined with any other

output when stacked in series.

If combining outputs in parallel,

only outputs of the same voltage

may be used together.

• The Iso-Brick Power Supply’s

foldback current limiting circuit

(FCLC) provides ultimate protec-

tion against power shorts and

overloads. Even at full load, the

Iso-Brick Power Supply operates

coolly and quietly as a fully regu-

lated power supply.

SPECIFICATIONS

INPUT 18V @ 2 Amps

regulated supply (positive barrel

negative center 5.5mm x 2.1mm

plug)

OUTPUTS 6-15V @ 250mA (2)

18V @ 250mA (2)

9V @ 450mA (2)

9V @ 300mA (2)

9V @ 100mA (2)

(all positive barrel negative center

5.5mm x 2.1mm)

Product specificaties

Merk:	MXR
Categorie:	Niet gecategoriseerd
Model:	Iso-Brick M238

Heb je hulp nodig?

Als je hulp nodig hebt met MXR Iso-Brick M238 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd MXR

MXR Iso-Brick M238 Handleiding

18 Augustus 2023

MXR M-103 Handleiding

26 Juli 2023

MXR Dyna Comp M282 Handleiding

26 Juli 2023

MXR Smart Gate M-135 Handleiding

26 Juli 2023

MXR MC-404 CAE WAH Handleiding

26 Juli 2023

MXR Dime Distortion DD-11 Handleiding

26 Juli 2023

MXR M195 Noise Clamp Handleiding

26 Juli 2023

MXR Mini Iso-Brick M239 Handleiding

11 Juni 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024

Kramer K-Bar Camera Bracket Handleiding

26 November 2024

Kramer RK-19 Handleiding

26 November 2024

Kramer OSP-MM1 Handleiding

26 November 2024

Kramer ASPEN-1616UX Handleiding

26 November 2024

Korg Pitchstrap Handleiding

26 November 2024

NeoMounts WL70-450BL11 Handleiding

26 November 2024

Kramer CLS-AOCH/60 Handleiding

26 November 2024

Klauke EKM 6022ISM Handleiding

26 November 2024