Moxa OnCell G3150 Handleiding

Moxa Niet gecategoriseerd OnCell G3150

Lees hieronder de 📖 handleiding in het Nederlandse voor Moxa OnCell G3150 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 205 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

— 1 — — 2 — — 3 —

OnCell G3100 Series

Quick Installation Guide

Second Edition, September 2008

1. Overview

There are currently four models in the OnCell G3100 series of

IP-modems: the OnCell G3110, OnCell G3150, OnCell G3110-HSDPA,

and OnCell G3150-HSDPA. The main difference between the models is

the serial interface type. The OnCell G3100 industrial RS-232,

RS-232/422/485 GSM/GPRS/EDGE, or UMTS/HSDPA IP modems are

some of the most affordable, secure, and versatile products available in

the cellular networking market today. These modems also provide remote

access and TCP/IP support, and can be configured over a network.

2. Package Checklist

Before Installing the OnCell G3100 IP modem, verify that the package

contains the following items:

Standard Accessories

y Document & Software CD

y Omni 1 dBi rubber SMA antenna (OnCell G3100 model name:

ANT-CQB-O-1; OnCell G3100-HSDPA model name:

ANT-WCDMA-O-1.5 BK)

y Din-Rail Kit

y 5-pin terminal block (screw type)

y 10-pin terminal block (screw type)

y Product warranty statement

y Quick Installation Guide

Optional Accessories

y Power Adaptor: 1.2 A (or above) @ 12V

y DC power supply

y Power jack to terminal block cable

y Quad-band GSM/GPRS/EDGE antennas for OnCell G3110/G3150

series (impedance = 50 ohms):

ANT-CQB-O-0-3m: Omni 0dBi/10cm, magnetic SMA antenna, 3 m

ANT-CQB-O-3-3m: Omni 3dBi/25cm, magnetic SMA antenna, 3 m

ANT-CQB-O-5-3m: Omni 5dBi/37cm, magnetic SMA antenna, 3 m

Note: Please notify your sales representative if any of the above items are

missing or damaged.

3. Hardware Introduction

Front View Rear View

OnCell G3110/G3150 OnCell G3110-HSDPA/

G3150-HSDPA

SIGNAL

PWR 2

FAULT

GPRS

PWR 1

READY

GSM

Tx Rx

Ethernet

SMA Bulkhead Jack

SIGNAL

PWR 2

FAULT

GPRS

PWR 1

READY

GSM

UMTS

HSDPA

Ethernet

SMA Bulkhead Jack

DIN-rail Support

Matel Springs

Top View

PWR 2/PWR 1DI 2/DI 1 Relay

RESET

Bottom Views

OnCell G3110/G3110-HSDPA OnCell G3150/G3150-HSDPA

RS-232

RS-232 RS-422/485

Side Views

SIM card Cover

Left Side Right Side

Reset Button—Press the Rest button continuously for 5 sec to load

factory defaults: Use a pointed object, such as a straightened paper clip or

toothpick, to press the reset button. This will cause the Ready LED to

blink on and off. The factory defaults will be loaded once the Ready LED

stops blinking (after about 5 seconds). At this point, you should release

the reset button (the default IP is 192.168.127.254).

LED Indicators

The LED indicators on the front panel of the OnCell G3100 are described

in the following table.

LED

Name

LED

Color LED Function

Green DC Power is active

Power Off Power is off, or power error condition exists.

Green Serial Tx

Amber Serial Rx

Data

Off Ethernet cable is disconnected.

Amber GSM is connected.

GSM Off GSM is disconnected.

Amber GPRS is connected.

GRPS Off GPRS is disconnected.

Amber UMTS is connected.

(OnCell G3100-HSDPA only)

UMTS

Off UMTS is disconnected.

(OnCell G3100-HSDPA only)

Amber HSDPA is connected.

(OnCell G3100-HSDPA only)

HSDPA

off HSDPA is disconnected.

(OnCell G3100-HSDPA only)

Green Steady on: Software Ready.

Blinking slowly (1 sec): The OnCell has been

located by the OnCell Search Utility.

Ready

Off Power is off, or is booting up.

Red Steady on: Booting up, or IP fault.

Blinking slowly (1 sec): Cannot get an IP address

from the DHCP server

Fault

Off Power is off, or there is no error condition.

Signal

(3 LEDs) Green

Number of lit LEDs indicates signal level

(at least 2 LEDs must illuminated for data

transmission)

Digital Input and Output

Six terminals on the terminal block are reserved for the I/O ports, with 2

terminals used for each input, and 2 terminals used for each output.

Digital Input—Digital ON and OFF determine which power input is used:

DIN OFF: 0 to 3.3 VDC

DIN ON: 10 to 48 VDC (DI COM to DI)

Digital Output—The default for the relay output (DOUT) is open,

indicating a normal condition. If the relay output (DOUT) is shorted, it

indicates an exception.

P/N: 1802031000011

— 4 — — 5 — — 6 —

Adjustable pull high/low resistor for RS-485 Port

DIP switches on the bottom of the OnCell G3100 are used to set the pull

high/low resistor value for each serial port.

1 2 3 4

ON DIP

1 2 3

SW Pull High Pull Low Terminator

ON 1 KΩ 1 KΩ 120 KΩ

OFF 150 KΩ 150 KΩ ---

4. Hardware Installation Procedure

STEP 1: Open the SIM cover, and insert the SIM card in the SIM card

slot.

STEP 2: Connect the 12-48 VDC power adaptor to the OnCell G3100

and then plug the power adaptor into a DC outlet.

STEP 3: To configure the OnCell, use an Ethernet cable to connect the

OnCell directly to your computer’s Ethernet interface.

STEP 4: Connect the OnCell G3100’s serial port to a serial device.

5. Software Installation Information

The Document & Software CD contains the User’s Manual, OnCell

Search Utility, and OnCell Driver Manager. Insert the CD and follow the

on-screen instructions. Please refer to the User’s Manual for additional

details on using the OnCell Search and Driver Manager.

6. Pin Assignments and Cable Wiring

DB9 Male Port Pinouts

Note that the OnCell G3110 only supports RS-232. The RS-422/485 pin

assignments only apply to the OnCell G3150.

DB9 Male

54321

9876

Pin RS-232

1 DCD

2 RxD

3 TxD

4 DTR

5 GND

6 DSR

7 RTS

8 CTS

9 ---

4W/2W RS-485/RS-422 (Terminal Block) Pinouts

Serial Device

Signals

Rx+

Rx-

Tx+/ Data+

Tx-/ Data-

GND GND

R- / D-

R+ / D+

T-

T+

OnCell G3150

Terminal Block

Pin RS-422/485

4-wire

RS-485

2-wire

1 TxD+(B) ---

2 TxD-(A) ---

3 RxD+(B) Data+(B)

4 RxD-(A) Data-(A)

5 GND GND

Power Input and Relay Output Pinouts

PIN 1 2 3 4 5 6 7 8 9 10

Name V1+ V1- V2+ V2- I1 COM_1 I2 COM_2

Function DC

Power

input 1

Power

input 1

Power

input 2

Power

input 2

Relay

Out Relay

Out Digital

Input Digital

Input

GND

Digital

Input Digital

Input

GND

7. Specifications

LAN Interface

Ethernet 10/100 Mbps, RJ45 connector

Protection Built-in 1.5 KV magnetic isolation

Cellular Interface (for OnCell G3110 & G3150)

Standard Compliance GSM/GPRS/EDGE

Band Selection Quad-band 850/900 MHz, and 1800/1900 MHz

Tx Power 1 watt GSM 1800/1900, 2 watt EGSM 850/900

GPRS Multi-slot class Class 12

GPRS Terminal Device Class B

GPRS Coding Schemes CS1 to CS4

SIM Control 3V

Cellular Interface (for OnCell G3110-HSDPA & G3150-HSDPA)

Standard Compliance UMTS/HSDPA

Band Selection Tri-band 850/1900/2100 MHz Quad-band

850/900/1800/1900MHz

Tx Power 1 watt GSM1800, 2 watt GSM900,

0.25 watt UMTS/HSDPA,

0.5 watt EDGE900, 0.4 watt EDGE1800

GPRS Multi-slot class Class 10

GPRS Terminal Device Class B

GPRS Coding Schemes CS1 to CS4

SIM Control 3V

Serial Interface

No. of Ports 1

Serial Standards G3100: RS-232 (DB9 male connector)

G3150: RS-232 (DB9 male connector),

RS-422/485 (5-pin terminal block

connector)

Serial Communication Parameters

Parity None, Even, Odd, Space, Mark

Data Bits 5, 6, 7, 8

Stop Bit(s) 1, 1.5, 2 (when parity = None)

Flow Control RTS/CTS, XON/XOFF

Speed 50 bps to 921.6 Kbps

I/O Interface

Alarm Contact 1 relay output with current carrying capacity of

1A@24 VDC

Digital Input 2 inputs electrically isolated from the electronics

Power Requirements

Input Voltage 12 to 48 VDC

Data Link 585 to 900 mA (peak) @ 12 V

Environmental Limits

Operating temperature -30 to 55°C (-22 to 131°F), 5 to 95% RH

Storage temperature -40 to 75°C (-40 to 167°F)

Regulatory Approvals

EMC CE Class A , FCC Class A, UL

Warranty

Warranty Period 5 years

Moxa Inc.

Reproduction without permission is prohibited.

Tel: +886-2-8919-1230 www.moxa.com

Fax: +886-2-8919-1231 support@moxa.com

Product specificaties

Merk:	Moxa
Categorie:	Niet gecategoriseerd
Model:	OnCell G3150
Gewicht:	440 g
Materiaal behuizing:	Aluminium
Soort serieële aansluiting:	RS-232/422/485
Aantal Ethernet LAN (RJ-45)-poorten:	1
Certificering:	CE, FCC, EN, PTCRB
Ingangsspanning:	12 - 48 V
Ethernet LAN, data-overdrachtsnelheden:	10, 100 Mbit/s
Antenne versterkingsniveau (max):	0 dBi
Soort apparaat:	Gateway voor mobiele netwerken
Temperatuur bij opslag:	-40 - 75 °C
Datanetwerk:	EDGE, GPRS, GSM
Compatibele besturingssystemen:	Windows 95/98/ME/NT/2000\nWindows XP (32/64-bit)\nWindows 2003 (32/64-bit)\nWindows Vista (32/64-bit)\nWindows Server 2008 (32/64-bit)\nSCO Unix\nSCO OpenServer 5/6\nUnixWare 7\nSVR4.2\nQNX 4.25/6\nSolaris 10\nFreeBSD 5/6\nLinux 2.2.x, 2.4.x, 2.6.x
Ondersteunde netwerkprotocollen:	ICMP, TCP/IP, UDP, DHCP, Telnet, DNS, HTTP, SMTP, HTTPS, SNTP, ARP, SSL, IPSec
Aantal SIM cards:	1
GSM bands ondersteund:	850,900,1800,1900 MHz
Firewall:	Ja
IP-adresfilter:	Ja
Veiligheid:	UL60950-1
Aansluiting antenne:	SMA
Mean time between failures (MTBF):	339045 uur
Auto MDI/MDI-X:	Ja
Afmetingen (B x D x H):	28 x 93 x 126 mm
Montage:	DIN-rail
Network address translation (NAT):	Ja
GPRS multislot klasse:	12
Seriële poort(en):	1
Beheerprotocollen:	SNMP MIB-II, SNMP Private MIB, SNMPv1/v2c/v3, DDNS, IP Report, Web/Telnet/Serial-Console/SSH
Bedrijfstemperatuur (T-T):	-30 - 55 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 95 procent
Isolatie:	1.5 kV
Port forwarding:	Ja
Electrostatic Discharge (ESD) bescherming:	15 kV
Baud snelheid:	0.05 Kbit/s
RS-422 signalen:	RxD+, RxD-, SGND, TxD+, TxD-
RS-485 signalen:	Data+, Data-, RxD+, RxD-, SGND, TxD+, TxD-
Data bits:	5, 6,7, 8
RS-232 signalen:	CTS, DCD, DSR, DTR, GND, RTS, Rx, Tx
Overspanningsbeveiliging in voltage:	2 kV
SIM interface:	3 V
GPRS coderings schemas:	CS1, CS2, CS3, CS4