Monogram JXFLUSH1 Handleiding

Monogram Niet gecategoriseerd JXFLUSH1

Lees hieronder de 📖 handleiding in het Nederlandse voor Monogram JXFLUSH1 (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 7 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/3
Installation
Instructions
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT — Save these instructions
for local inspector’s use.
• IMPORTANT — Observe all governing
codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note – The flush-mounted cooktop must be
properly grounded.
FOR YOUR SAFETY
Review all Safety, Power Requirements,
Dimensions and Clearances and Preparation of
the cutout opening instructions in the Installation
Instructions included with your cooktop.
NOTICE — Read all instructions thoroughly,
PRIOR to beginning any work. Actual product
dimensions may vary due to manufacturing
tolerances.
WARNING To avoid the risk of property
damage, the cutout should be made by a professional
cabinet installer.
WARNING Do not attempt to flush-mount
any cooktop counter unit that requires a down draft
ventilation system.
WARNING Installer must ensure that the
counter is capable of holding at least 300 lbs. once
the cooktop has been flush mounted.
JXFLUSH1
Cooktop Flush-Mount Kit
KIT INCLUDES
• Installation Instructions
• (2) 60” long 3/4” wide one sided foam tape
• (2) 130” long 3/4” wide one sided Teflon tape
• Hold Down Bracket Hardware:
(2) hold down bracket
(2) 3/8” long 1/4” hex head screw
(2) 2 1/2” long thumb screw
MATERIALS YOU WILL NEED
• High-temperature sealant meeting the following
requirements:
- Only certain models may be installed over wall
ovens. The wall oven and cooktop will both have
a label stating which models are approved in
combination.
- 100% Silicone
- Temperature rating – 400°F minimum
- Tack free time – 30 minutes minimum
- Recommendation:
GE SUPREME 100% Silicone “CLEAR”
• Caulking tool(s) to shape/finish the silicone bead.
• 2 Heavy duty suction cups, each rated for 100 lbs.
minimum.
• Masking tape
• Measuring tape
• Pencil
• Scraper
CUTTING THE COUNTERTOP
If you are installing the cooktop in a solid surface
material such as granite, quartz or any other natural
or synthetic solid surface, we recommend that the
flush-mount cutout be prepared by a professional
cabinet or countertop installer.
Cooktop cutouts in wood or wood-laminate
countertops may be able to be prepared using a 1½
HP (minimum) router and carbide router bit.
If you have questions, call GE Appliances at 800.GE.CARES (800.432.2737)
or visit our website at: GEAppliances.com.
31-11024 09-16 GEA
231-11024
Installation Instructions
1. Initially prepare the cutout as per the installation
instructions that were supplied with your cooktop.
IMPORTANT: Prior to final installation of the unit
in the flush-mount cutout using the silicone caulk,
temporarily make all wiring connections and
check the unit per the installation instructions to
ensure it is working properly. The unit should be
re-wired and re-checked for correct working upon
final installation.
2. Use a pencil and measuring tape to prepare the
cutout area by marking it off per the dimensions
on page 4.
3. The cutout must be made to a maximum depth of
ó´DQGVKRXOGDOZD\VOHDYHDWOHDVWDǩ´JDSDOO
around the edge of the cooktop.
IMPORTANT: To ensure sufficient support for the
cooktop while cooking, reinforcing strips of wood
or solid surface material must be secured in place
below the edge of the cutout (see illustration).
Ensure sufficient support is provided in all
necessary locations on the countertop. Follow all
countertop manufacturer installation instructions.
WARNING Failure to provide adequate
countertop reinforcement for cooktop may result
in damage to unit when weight is added to
cooktop during cooking.
INSTALLING THE COOKTOP
4. Vacuum dust and other particles from the cooktop
cutout.
5. Apply the black foam tape provided in the kit to
the top of the rabbeted edge of the countertop,
flush with the outer edge of the rabbet (see
picture in step 3.) The foam tape will keep the
silicone sealant from seeping between the
countertop and the underside of the cooktop.
Make sure the foam tape does not overlap - it
needs to be a single thickness for proper spacing.
6. Apply the Teflon tape to the underside of the
cooktop flush with the outside edge of the glass
and partially covering the metal flange (see picture
in step 3.) Trim the Teflon tape at the corners of
the cooktop to match the curve of the glass. The
Teflon tape will keep the silicone sealant from
seeping between the glass and the metal.
7. Install the hold-down brackets provided in the kit
onto the cooktop (both sides). DO NOT TIGHTEN
YET. Turn the brackets inwards to avoid
interference when dropping the cooktop into the
countertop. The baffle supplied with the cooktop
needs to be attached as well, unless the cooktop
is being installed over a single wall oven.
Baffle
Screws
Bottom of Cooktop
Foam tape
(Compressed)
Ensure cooktop sits
on the metal flange
on all four sides
Countertop
Teflon tape
Glass
Silicone Caulk
Reinforcing strip
Cooktop burner box
1/4”
Max.
1/8” Min.
31-11024 3
Installation Instructions
INSTALLING THE COOKTOP
8. Using the heavy duty suction cups (not provided)
lift and place the cooktop into the prepared
cutout.
CAUTION
Ensure that the cooktop
surface is higher than the countertop surface
to prevent hot cookware from contacting the
countertop. If necessary, add wooden shims
under the foam tape where needed around the
perimeter of the cooktop to increase the height.
Make sure the foam and Teflon tapes contact
around the entire perimeter.
9. Make all wiring connections and check unit per
the installation instructions to ensure that it is
working correctly
10. Align the cooktop in the opening allowing for
equal clearance on all sides.
11. Access the bottom of the cooktop below the
countertop and tighten the screws on the
hold-down brackets. Turn the thumbscrew until it
touches the bottom of the countertop (see picture).
IMPORTANT: Turn the thumbscrew just until it
touches the bottom of the countertop. DO NOT
OVERTIGHTEN.
12. Using masking tape (not provided), place a border
around the edge of the cooktop cutout and the
edges of the glass. This will prevent the silicone
sealant from sticking to the top surface of the
countertop or to the glass surface of the cooktop.
WARNING Do not allow silicone sealant
to come into contact with the top surface of the
glass cooktop.
13. Ensure the area is well ventilated when applying
sealant. Apply high-temperature 100% silicone
sealant (not provided) into the opening between
the countertop edge and the edge of the glass
cooktop, one side at a time. It is important to wipe
away any sealant on the glass and countertop
immediately as the sealant can begin to form a
skin fairly quickly. Use only a high-temperature
100% silicone sealant that meets the listed
specifications. Use a caulking tool to finish the
surface of the bead to get a smooth look.
14. Do not touch the sealant, or move or use the
cooktop for the amount of time listed as the full
cure time for the sealant. Protect the area from
dust for at least 2 hours.
15. Allow the sealant to cure for the manufacturer’s
recommended time, then remove the masking
tape from the countertop and glass cooktop.
Clean any excess sealant on the cooktop and
countertop with the scraper.
Countertop
Cooktop
Hold Down
Bracket
Cooktop
Glass
Countertop
Masking tape
Make sure tape does not cross
area to fill with silicone sealant

Product specificaties

Merk: Monogram
Categorie: Niet gecategoriseerd
Model: JXFLUSH1

Heb je hulp nodig?

Als je hulp nodig hebt met Monogram JXFLUSH1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Monogram

Monogram

Monogram ZKSB3H3PNSS Handleiding

16 Oktober 2024
Monogram

Monogram ZKR36R Handleiding

16 Oktober 2024
Monogram

Monogram ZKR72R Handleiding

16 Oktober 2024
Monogram

Monogram ZK1SN249NLH Handleiding

26 September 2024
Monogram

Monogram ZK1SN244NRH Handleiding

26 September 2024
Monogram

Monogram ZWL1126SRSS Handleiding

21 Augustus 2024
Monogram

Monogram JXFLUSH1 Handleiding

21 Augustus 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Powerfix

Powerfix Z31036 Handleiding

16 November 2024
EMOS

EMOS DCAZ10 Handleiding

16 November 2024
Roland

Roland KS-V7 Handleiding

16 November 2024
Zebra

Zebra WS50 Handleiding

16 November 2024
Babyzen

Babyzen YOYO board Handleiding

16 November 2024
DataVideo

DataVideo TTL-100 Handleiding

16 November 2024
Hager

Hager FN296E Handleiding

16 November 2024
Aqua Joe

Aqua Joe AJ-SPXN Handleiding

16 November 2024
Hager

Hager FN117E Handleiding

16 November 2024
Hager

Hager FN097E Handleiding

16 November 2024