Milwaukee V28 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee V28 (4 pagina's) in de categorie Zaklampen. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
WORK LIGHT
Compatible with MILWAUKEE V28 Lithium-Ion Battery Packs
LAMPE DE TRAVAIL
Compatible avec batterie
Lithium-Ion
V28
MILWAUKEE
LAMPARA DE TRABAJO
Compatible con baterías Iones de Litio de de V28 MILWAUKEE
Cat. No.
No de Cat.
49-24-0185
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
TO REDUCE THE RISK OF INJURY, USER MUST READ OPERATOR'S MANUAL.
AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE LE
MANUEL DE L'UTILISATEUR.
PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER EL MANUAL
DEL OPERADOR.
2 3
ASSEMBLY
Replacing the Bulb
1. Remove battery pack before changing
bulb.
2. Unscrew the bezel assembly on pivot
head by turning counterclockwise.
3. Remove the bezel assembly.
4. Pull forward the aluminum heat sink.
5. Gently rotate the bulb counter
clockwise and pull out.
To reduce the risk of injury, DO
NOT operate work light without
bezel assembly in place. Bulb does
get hot. Always remove battery
pack before changing or removing
bulbs. Always allow the work light
to cool for at least 10 minutes
before replacing the bulb.
Fig. 2
Bezel
assembly
Spare bulb storage
Bulb
Aluminum
heat sink
Pivot
head
To install new bulb, follow above
directions in reverse.
NOTE: Use a soft cloth when installing bulbs.
Direct contact with oils or other contamina-
tion can shorten the life of bulbs.
F o r wo rk l ig ht 4 9- 2 4 - 01 8 5 , us e
replacement bulb 49-81-0040.
A spare bulb is provided with the work
light. The bulb is located behind the
aluminum heat sink.
See your nearest MILWAUKEE Retailer
or Service Center to obtain replacement
bulbs.
To reduce the risk of injury, do not
look directly into the light when the
work light is on.
Adjusting the Pivot Head
The pivot head can pivot to a range of 140°;
110° up and 30° down with detents every
10°. Pivot head to desired position (Fig. 1).
Allow the detent to snap into place. Do not
forcibly pivot the head.
Fig. 1
Removing Battery Pack from Tool
Push in the release buttons and pull the
battery pack away from the tool.
Inserting Battery Pack into Tool
To insert the battery pack onto the tool, slide
the pack onto the body of the tool. Make sure
it latches securely into place.
To reduce the risk of injury and
damage, never insert bulbs other
than MILWAUKEE 28V bulbs in the
bulb socket. Other bulbs will over
heat!
Intelligent Circuit
This work light is equipped with an
intelligent circuit. If an improper voltage
bulb is installed, the light will flash
repeatedly. If this occurs, remove the
improper bulb and install a MILWAUKEE
28V bulb.
• Read all the instructions before using
the appliance.
• To reduce the risk of injury, close super-
vision is necessary when an appliance is
used near children.
• Do not use outdoors.
• For a rechargeable appliance - Use only
the charger supplied by the manufacturer
to recharge.
• For an appliance with a replaceable
lamp - always unplug before replacing the
lamp. See "Specifi cations" for replacement
bulbs.
• Know your work light. Read this manual
carefully to learn your work light's applica-
tions and limitations as well as potential
hazards associated with this type of tool.
• Batteries must be recharged only with
the specifi ed charger for the battery. A
charger that may be suitable for one type
of battery may create a risk of fi re when
used with another battery.
• Use work light only with specifi cally
designated battery pack. Use of any
other batteries may create a risk of fi re.
READ AND UNDERSTAND ALL INSTRUCTIONS.
When using electric appliances, basic precautions should always be followed,
including the following:
WARNING
IMPORTANT SAFETY INSTRUCTIONS
• When battery pack is not in use, keep
it away from metal objects like: paper
clips, coins, keys, nails, screws, or
other small metal objects that can
make a connection from one terminal
to another. Shorting the battery terminals
together may cause sparks, burns, or a
fi re.
• N ev er in se rt bu lb s oth er th an
MILWAUKEE bulbs in the bulb socket.
Bulbs other than MILWAUKEE bulbs
may cause short circuit of battery and
personal injury.
• Store idle work light out of reach
of children. Warm work lights can
become hazardous in the hands of chil-
dren.
• Maintain labels and nameplates.
These carry important information.
If unreadable or missing, contact a
MILWAUKEE service facility for a free
replacement.
Volts DC
28
Cat. No.
49-24-0185
Specifi cations
Volts Direct Current
Symbology
Underwriters Laboratories, Inc.
Before using the work light, read this operator's manual, your battery pack and charger
operator's manual, and all labels on the battery pack, charger and work light.
SAVE THESE
INSTRUCTIONS
Replacement Bulbs
49-81-0040
WARNING
WARNING WARNING
4 5
OPERATION
To turn the work light, slide the switch on
to . ON
To turn the work light, slide the switch off
to .OFF
Fig. 3
ON
OFF Switch
Clip-LokTM System
The Clip-Lok system consists of two pieces;
the belt clip and the tool holder.
Fig. 4
Attaching the Belt Clip
The belt clip can be mounted to tool belts,
bags, buckets, etc. To mount the belt clip:
1. Pull up the clamp release. The clamp
will pop out.
2. Slide the clamp over the tool belt, bag,
bucket, etc.
3. Press in the clamp to tighten.
Using the Clip-Lok Tool Holder
1. To attach the tool to the belt clip, slide
the tool holder over the stud on the belt
clip until it is held in place by the protrud-
ing pin.
2. To release the tool from the belt clip,
grasp the tool handle, push down on
the tool release lever with your thumb,
and pull up on the tool.
Belt clip
Tool release lever
Stud
Pin
Clamp
Clamp
release
Tool holder
Front tangs
Cleaning
Keep tool handles clean, dry and free of oil
or grease. Use only mild soap and a damp
cloth to clean the tool, battery pack and
charger since certain cleaning agents and
solvents are harmful to plastics and other
insulated parts. Some of these include gaso-
line, turpentine, lacquer thinner, paint thinner,
chlorinated cleaning solvents, ammonia and
household detergents containing ammonia.
Never use fl ammable or combustible sol-
vents around tools.
To reduce the risk of personal injury
and damage, never immerse your
tool, battery pack or charger in liquid
or allow a liquid to fl ow inside them.
WARNING
Maintain Work Light
Keep your work light, battery pack and
charger in good repair by adopting a
regular maintenance program.
If the work light does not work prop-
erly, return the work light to a MILWAUKEE
service facility for repairs.
MAINTENANCE ACCESSORIES
Always remove battery pack before
changing or removing accessories.
Only use accessories specifi cally
recommended for this tool. Others
may be hazardous.
For a complete listing of accessories refer to
your MILWAUKEE Electric Tool catalog or go
on-line to www.milwaukeetool.com. To obtain
a catalog, contact your local distributor or a
service center listed on the back cover of this
operator’s manual.
WARNING
To reduce the risk of injury, al-
ways unplug the charger and
remove the battery pack from the
charger or tool before performing any
maintenance. Never disassemble the
tool, battery pack or charger. Contact
a MILWAUKEE service facility for ALL
repairs.
WARNING
Product specificaties
| Merk: | Milwaukee |
| Categorie: | Zaklampen |
| Model: | V28 |
Heb je hulp nodig?
Als je hulp nodig hebt met Milwaukee V28 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Zaklampen Milwaukee
4 Oktober 2022
Handleiding Zaklampen
- Zaklampen Panasonic
- Zaklampen Alecto
- Zaklampen Ansmann
- Zaklampen LED Lenser
- Zaklampen Makita
- Zaklampen Silva
- Zaklampen Worx
- Zaklampen Crivit
- Zaklampen Black And Decker
- Zaklampen Anslut
- Zaklampen Barska
- Zaklampen Fenix
- Zaklampen Klarus
- Zaklampen Maglite
- Zaklampen Masai
- Zaklampen Nitecore
- Zaklampen Olight
- Zaklampen Pelican
- Zaklampen Petzl
- Zaklampen Streamlight
Nieuwste handleidingen voor Zaklampen
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022