Milwaukee M12 2438-22 Handleiding
Milwaukee
Schuurmachine
M12 2438-22
Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee M12 2438-22 (20 pagina's) in de categorie Schuurmachine. Deze handleiding was nuttig voor 54 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/20
Cat. No. / No de cat.
2438-20
M12â„¢ 2" SANDER / 3" POLISHER
PONCEUSE 51 mm (2") / POLISSEUSE 76 mm (3") M12â„¢
LIJADORA DE 51 mm (2") / PULIDORA DE 76 mm (3") M12â„¢
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
2
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING
Read all safety warnings, instruc-
tions, illustrations and speciîš¿ca-
tions provided with this power tool. Failure to
follow all instructions listed below may result in
electric shock, îš¿re and/or serious injury. Save all
warnings and instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-oper-
ated (cordless) power tool.
WORK AREA SAFETY
• Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Un-
modiîš¿ed plugs and matching outlets will reduce risk
of electric shock.
• Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
• Do not abuse the cord. Never use the cord for car-
rying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk
of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
• If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of an GFCI reduces
the risk of electric shock.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
• Use personal protective equipment. Always wear
eye protection. Protective equipment such as a dust
mask, non-skid safety shoes, hard hat or hearing
protection used for appropriate conditions will reduce
personal injuries.
• Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your îš¿nger on the
switch or energizing power tools that have the switch
on invites accidents.
• Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result
in personal injury.
• Do not overreach. Keep proper footing and bal-
ance at all times. This enables better control of the
power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewelry. Keep your hair and clothing away from
moving parts. Loose clothes, jewelry or long hair can
be caught in moving parts.
• If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust col-
lection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause
severe injury within a fraction of a second.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
• Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
• Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
• Maintain power tools and accessories. Check for
misalignment or binding of moving parts, break-
age of parts and any other condition that may af-
fect the power tool’s operation. If damaged, have
the power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a hazard-
ous situation.
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles
and grasping surfaces do not allow for safe handling
and control of the tool in unexpected situations.
BATTERY TOOL USE AND CARE
• Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of îš¿re when used
with another battery pack.
• Use power tools only with specically designated
battery packs. Use of any other battery packs may
create a risk of injury and îš¿re.
• When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another. Shorting the battery terminals together may
cause burns or a îš¿re.
3
• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact ac-
cidentally occurs, ush with water. If liquid con-
tacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
• Do not use a battery pack or tool that is damaged
or modiîš¿ed. Damaged or modiîš¿ed batteries may ex-
hibit unpredictable behavior resulting in îš¿re, explosion
or risk of injury.
• Do not expose a battery pack or tool to re or
excessive temperature. Exposure to îš¿re or tem-
perature above 265°F (130°C) may cause explosion.
• Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range speciîš¿ed in the instructions. Charging im-
properly or at temperatures outside the speciîš¿ed range
may damage the battery and increase the risk of îš¿re.
SERVICE
• Have your power tool serviced by a qualied
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
• Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
SPECIFIC SAFETY RULES FOR
SANDER/POLISHER
Safety Warnings Common for Sanding and Polish-
ing Operations:
• This power tool is intended to function as a sander
or polisher. Read all safety warnings, instructions,
illustrations and speciîš¿cations provided with this
power tool. Failure to follow all instructions listed
below may result in electric shock, îš¿re and/or serious
injury.
• Operations such as grinding, wire brushing
or cutting-off are not recommended to be per-
formed with this power tool. Operations for which
the power tool was not designed may create a haz-
ard and cause personal injury.
• Do not use accessories which are not specically
designed and recommended by the tool manufac-
turer. Just because the accessory can be attached to
your power tool, it does not assure safe operation.
• The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated
speed can break and y apart.
• The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories can-
not be adequately guarded or controlled.
• Threaded mounting of accessories must match
the grinder spindle thread. For accessories
mounted by anges, the arbour hole of the ac-
cessory must fit the locating diameter of the
ange. Accessories that do not match the mounting
hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
• Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels
for chips and cracks, backing pad for cracks, tear
or excess wear, wire brush for loose or cracked
wires. If power tool or accessory is dropped, in-
spect for damage or install an undamaged acces-
sory. After inspecting and installing an accessory,
position yourself and bystanders away from the
plane of the rotating accessory and run the power
tool at maximum no-load speed for one minute.
Damaged accessories will normally break apart during
this test time.
• Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and workshop apron
capable of stopping small abrasive or workpiece
fragments. The eye protection must be capable of
stopping ying debris generated by various opera-
tions. The dust mask or respirator must be capable
of îš¿ltrating particles generated by your operation.
Prolonged exposure to high intensity noise may cause
hearing loss.
• Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment. Fragments of
workpiece or of a broken accessory may y away and
cause injury beyond immediate area of operation.
• Hold the power tool by insulated gripping surfaces
only, when performing an operation where the cut-
ting tool may contact hidden wiring. Contact with
a "live" wire may also make exposed metal parts of
the power tool "live" and could give the operator an
electric shock.
• Never lay the power tool down until the acces-
sory has come to a complete stop. The spinning
accessory may grab the surface and pull the power
tool out of your control.
• Do not run the power tool while carrying it at your
side. Accidental contact with the spinning accessory
could snag your clothing, pulling the accessory into
your body.
• Regularly clean the power tool’s air vents. The
motor’s fan will draw the dust inside the housing
and excessive accumulation of powdered metal may
cause electrical hazards.
• Do not operate the power tool near ammable
materials. Sparks could ignite these materials.
• Do not use accessories that require liquid cool-
ants. Using water or other liquid coolants may result
in electrocution or shock.
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or snagged
rotating wheel, backing pad, brush or any other acces-
sory. Pinching or snagging causes rapid stalling of the
rotating accessory which in turn causes the uncon-
trolled power tool to be forced in the direction opposite
of the accessory’s rotation at the point of the binding.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel that
is entering into the pinch point can dig into the surface
of the material causing the wheel to climb out or kick
out. The wheel may either jump toward or away from
the operator, depending on direction of the wheel’s
movement at the point of pinching. Abrasive wheels
may also break under these conditions.
Kickback is the result of power tool misuse and/or in-
correct operating procedures or conditions and can be
avoided by taking proper precautions as given below.
• Maintain a rm grip on the power tool and posi-
tion your body and arm to allow you to resist
kickback forces. Always use auxiliary handle, if
provided, for maximum control over kickback or
torque reaction during start-up. The operator can
control torque reactions or kickback forces, if proper
precautions are taken.
• Never place your hand near the rotating acces-
sory. Accessory may kickback over your hand.
• Do not position your body in the area where power
tool will move if kickback occurs. Kickback will
Product specificaties
| Merk: | Milwaukee |
| Categorie: | Schuurmachine |
| Model: | M12 2438-22 |
Heb je hulp nodig?
Als je hulp nodig hebt met Milwaukee M12 2438-22 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Schuurmachine Milwaukee
19 Maart 2024
19 Maart 2024
6 Maart 2024
7 Mei 2023
1 Mei 2023
26 April 2023
6 April 2023
8 Februari 2023
23 Januari 2023
11 Januari 2023
Handleiding Schuurmachine
- Schuurmachine Bosch
- Schuurmachine AEG
- Schuurmachine DeWalt
- Schuurmachine Arendo
- Schuurmachine Batavia
- Schuurmachine Bavaria
- Schuurmachine Black Decker
- Schuurmachine Bort
- Schuurmachine Bruder Mannesmann
- Schuurmachine Dremel
- Schuurmachine Duro
- Schuurmachine Duro Pro
- Schuurmachine Einhell
- Schuurmachine Elu
- Schuurmachine Fein
- Schuurmachine Ferm
- Schuurmachine Festool
- Schuurmachine Flex
- Schuurmachine Gamma
- Schuurmachine Gastroback
- Schuurmachine Global
- Schuurmachine Gude
- Schuurmachine Hikoki
- Schuurmachine Hitachi
- Schuurmachine Holzmann
- Schuurmachine Hyundai
- Schuurmachine Kinzo
- Schuurmachine Kress
- Schuurmachine Maestro
- Schuurmachine Makita
- Schuurmachine Maktec
- Schuurmachine Matrix
- Schuurmachine Max
- Schuurmachine Metabo
- Schuurmachine Parkside
- Schuurmachine Powerplus
- Schuurmachine Protool
- Schuurmachine Rupes
- Schuurmachine Ryobi
- Schuurmachine Scheppach
- Schuurmachine Silverline
- Schuurmachine Skil
- Schuurmachine Stanley
- Schuurmachine Stomer
- Schuurmachine Toledo
- Schuurmachine Toolcraft
- Schuurmachine Topcraft
- Schuurmachine Trotec
- Schuurmachine Varo
- Schuurmachine Vonroc
- Schuurmachine Westfalia
- Schuurmachine Workzone
- Schuurmachine Worx
- Schuurmachine Ozito
- Schuurmachine Black And Decker
- Schuurmachine Cocraft
- Schuurmachine Meec Tools
- Schuurmachine Far Tools
- Schuurmachine Hilti
- Schuurmachine Power Craft
- Schuurmachine Tacklife
- Schuurmachine Truper
- Schuurmachine Fieldmann
- Schuurmachine Mafell
- Schuurmachine Proxxon
- Schuurmachine Biltema
- Schuurmachine Porter-Cable
- Schuurmachine Probuilder
- Schuurmachine Dedra
- Schuurmachine RIDGID
- Schuurmachine Tryton
- Schuurmachine Herkules
- Schuurmachine Craftsman
- Schuurmachine Rikon
- Schuurmachine Alpha Tools
- Schuurmachine Hazet
- Schuurmachine Stalco
- Schuurmachine Powertec
- Schuurmachine Meister Craft
- Schuurmachine King Craft
- Schuurmachine Toolson
- Schuurmachine Wagner SprayTech
- Schuurmachine Einhell Bavaria
- Schuurmachine McKenzie
- Schuurmachine Prowork
- Schuurmachine Proviel
- Schuurmachine Ribimex
- Schuurmachine FIXIT
- Schuurmachine Ergotools Pattfield
- Schuurmachine THUN
- Schuurmachine Bavaria By Einhell
- Schuurmachine Pevec
- Schuurmachine Handwerk
- Schuurmachine TAURUS Titanium
Nieuwste handleidingen voor Schuurmachine
10 December 2024
8 December 2024
5 December 2024
5 December 2024
4 December 2024
4 December 2024
4 December 2024
4 December 2024
4 December 2024
4 December 2024