Milwaukee 2776-21 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee 2776-21 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
2776-20 (Non-Remote)
M18â„¢ 3" Underground Cable CutterFORCELOGICâ„¢ Oct. 2019
54-00-2776
REVISED BULLETIN
SERVICE PARTS LIST
BULLETIN NO.
WIRING INSTRUCTION
DATE
CAT. NO.
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
SERIAL
NUMBER
Drwg. 2
H49A
Due to the combination of hydraulics and electronics in this tool,
service can only be performed at Milwaukee Authorized Hydraulic Repair Centers:
MILWAUKEE TOOL Central Repair
1401 Sycamore Avenue l Greenwood, MS 38930-7277
Please send your tool directly to this location for service.
Or
Via -Service at: www.milwaukeetool.com/e-servicee
questions, please call 1.800.SAWDUST (1.800.729.3878)
Or
Visit www.milwaukeetool.com to îš¿nd your closest
Milwaukee authorized Hydraulic repair center
Or
Return it to a MILWAUKEE Service Center location, freight prepaid and insured.factory
A copy of the proof of purchase should be included with the return product.
If you have questions please contact Milwaukee Product Service at:
Product Technical Support via phone at: 262.783.8642
Or
Via email at: METProductSupport @milwaukeetool.com
Disassembly is not recommended and could void the warranty.
2776R-20 (Wireless Remote)
CAT. NO. SERIAL
NUMBER H50A
LUBRICATION INSTRUCTIONS PAGE 3
CUTTER HEAD SERVICE PARTS PAGE 2
ACCESSORIES PAGE 2 TORQUE SPECIFICATIONS PAGE 4
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
83 12-20-0089 Service Nameplate (Not Shown) (1)
84 10-20-1119 Label for Wireless Remote (Not Shown) (1)
85 42-70-0027 Carabiner (Not Shown) (1)
86 48-22-8280 Underground Cutter Bag (Not Shown) (1)
87 22-80-2776 Remote Control
For 2776R-20 Only (Not Shown) (1)
Accessories and External Service Parts for 2776-20 & 2776R-20 3" Underground Cable Cutters
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 --------------- Underground Cutter Head Assembly (1)
1a --------------- M5 x 18mm Cap Screw 4mm Hex Drive (2)
1b --------------- Spring Washer (2)
1c --------------- Blade Retainer (1)
1d --------------- Left Blade (1)
1e --------------- M17 Nut (2)
1f --------------- M18 Screw Bolt (1)
1g --------------- Washer (3)
1h --------------- Right Blade (1)
1j 44-60-0049 Pin (4)
1k 44-66-0116 Connector Plate (4)
1m 44-14-0075 T-Connector (1)
1n 34-80-1300 Retaining Ring (4)
1p --------------- Clevis - Underground Cutter (1)
1q --------------- Stop Ring (1)
1r --------------- Bail Handle Grip (1)
1s --------------- M6 x 22mm Pan Hd. Phillips Screw (2)
1t --------------- Bail Handle Support - Left (1)
1u --------------- Bail Handle Support - Right (1)
1v --------------- M8 x 6.5 Screw with 8mm Hex Drive (2)
1w --------------- Extended Point Set Screw (1)
78 14-34-0122 Bail Handle Kit (1)
79 42-32-0265 Screw Bolt Kit (1)
80 44-60-0059 Pin Kit (1)
81 --------------- Clevis Assembly (1)
82 49-16-2774 Replacement UG Cutter Blade Set
(1)
1a(2x)
1b(2x)
1d
1j(4x)
1k(4x)
1n(4x)
1h
1c
1m
1f
1g(3x)
1p
1w
1q
1r
1s(2x)
1u
1v(2x)1t
1r 1s 1t
1u 1v
78
1e 1f
1g
79 1p
1q
81
1j
1n
80
1a 1b 1c
1d 1h 1n
82
1e(2x) Jam Nuts (Discard)
Nylok® Hex Nut (Use)
NOTE:
NOTE:
Correct placement of
pins (1j) and retaining
rings (1n) are important
for the proper function-
ing of the cutter head
assembly. Install as
illustrated with retaining
rings on flat side of
blade.
Flat side of blade
(Retaining ring side)
LUBRICATION INSTRUCTIONS S2 Grease, No. 49-08-5267
243 Blue Loctite ® Thread Sealant, 44-22-0095
NOTE
Regarding parts to be lubricated:
Apply a light coating of grease to all highlighted parts shown prior to
installation. Reference the key above for grease types.
NOTE
Regarding parts to receive thread locking sealant:
Place one to two drops of the recommended Loctite® thread locking
sealent (or the equivelant) to the threads of parts shown prior to
installation.
1j(4x)
1n(4x) 1e(2x) Jam Nuts (Discard)
Nylok® Hex Nut (Use)
NOTE:
The original design of this tool utilized two jam nuts (1e) to
aid in securing the Cutting Blades (82) in the Clevis
Assembly (81). One M17 Nylok® Hex Nut now replaces the
two jam nuts. When servicing the tool, DO NOT attempt to
reuse the two jam nuts...remove and discard.
NOTE:
Correct placement of pins (1j)
and retaining rings (1n) are
important for the proper
functioning of the cutter head
assembly. Install as illustrated
with retaining rings on flat
side of blade.
Flat side of blade
(Retaining ring side)


Product specificaties

Merk: Milwaukee
Categorie: Niet gecategoriseerd
Model: 2776-21

Heb je hulp nodig?

Als je hulp nodig hebt met Milwaukee 2776-21 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Milwaukee

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd