Milwaukee 2231-20 Handleiding

Milwaukee Meetapparatuur 2231-20

Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee 2231-20 (9 pagina's) in de categorie Meetapparatuur. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/9

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S

MANUAL.

AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN

COMPRENDRE LE MANUEL DE L'UTILISATEUR.

PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL

MANUAL DEL OPERADOR.

MILLIAMP CLAMP METER

PINCE AFFICHEUR DE COURANT MILLIAMPÈRES

MILIAMPERÍMETRO DE PINZA

Cat. No.

No de cat.

2231-20

H O L D R OZ E

H O L D R O

Z E

IMPORTANT SAFETY INSTRUCTIONS

WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS.

Failure to follow the warnings and instructions may result in electric shock, ﬁ re and/or serious

injury, as well as instrument damage and/or damage to the equipment being tested.

Save these instructions - This operator’s manual contains important safety and operating

instructions for the MILWAUKEE Milliamp Clamp Meter. Before using, read this operator’s

manual and all labels on the Clamp Meter.

GENERAL SPECIFICATIONS FUNCTIONAL DESCRIPTION

Accuracy is speciﬁ ed for 1 year after calibration, at

operating temperatures of 64°F to 82°F (18°C to

28°C), with relative humidity at 0 % to 85 % (NON-

CONDENSING).

Jaw Opening (maximum conductor size) ....

0.23" (6 mm)

Temperature ....

Operating: 14°F to 122°F (-10°C to 50°C)

Storage: -40°F to 140°F (-40°C to 60°C)

Temperature Coefficient .... 0.1 x (specified

accuracy)/°C (<18°C or >28°C)

Operating Altitude.... 0 to 2,000 meters

Drop Test .... 1 Meter

Battery .... 2 AA NEDA 15A, IEC LR6, 1.5V Alkaline

Battery Life .... Approx. 25 hours

Safety Compliances ....EN61010-1, UL 61010-1,

IEC 61010-2-32 (Clamp Assemblies),

IEC/EN 61010-1 2nd Edition for measurement

Category II, 60 V, Pollution Degree 2,

EMC EN61326-1

Certiﬁ cations .... cULus, CE

1. Worklight LED

2. Clamp storage

3. Low battery indicator

4. Primary measurement

5. Hold indicator

6. Worklight on/o

7. Power button

8. Hold button

9. Zero button

10. Units indicator

11. 4 to 20 mA Span

Percentage

12. Tactile barrier

13. Clamp

DANGER

Use only for tests on DC circuits. Do not use to test AC current.

Do not make tests on non-insulated conductors.

Do not attempt to make measurement in the presence of ﬂ ammable gasses. Otherwise, the

use of the instrument may cause sparking, which can lead to an explosion.

Transformer jaw tips are designed not to short the circuit under test. If equipment under test

has exposed conductive parts, however, extra precaution should be taken to minimize the

possibility of shorting.

Never attempt to use the instrument if its surface or your hand is wet.

Do not exceed the maximum allowable input of any measuring range.

Check meter functionality on a known circuit ﬁ rst. Never assume meter is working. Assume

circuits are live until they can be proven de-energized.

Do not ground yourself while measuring. Avoid body contact with earthed or grounded sur-

faces such as pipes, radiators, ranges and refrigerators.

Never open the battery cover during a measurement.

The instrument is to be used only in its intended applications or conditions. Otherwise, safety

functions equipped with the instrument doesn’t work, and instrument damage or serious

personal injury may be caused.

To reduce the risk of injury from shock and arc blasts, always wear personal protective

equipment where live conductors are exposed.

WARNING

Never attempt to make measurement if any abnormal conditions, such as broken case and

exposed metal parts are found on the instrument.

Verify proper operation on a known source before use or taking action as a result of the in-

dication of the instrument.

Do not install substitute parts or make any modiﬁ cation to the instrument. For repair or re-

calibration, return the meter to a factory Service/Sales Support Branch or authorized service

station.

Do not try to replace the batteries if the surface of the instrument is wet.

Disconnect all the cords and cables from the object under test and power o the instrument

before opening the battery cover for battery replacement.

This meter is designed to be powered by 2-AA batteries properly inserted into the MILWAUKEE

Clamp Meter. Do not attempt to use with any other voltage or power supply.

Install battery according to polarity (+ and –) diagrams.

Do not leave batteries within the reach of children.

Do not mix new and used batteries. Do not mix brands (or types within brands) of batteries.

Properly dispose of used batteries.

Do not incinerate or dismantle batteries.

Under abusive conditions, liquid may be ejected from the battery, avoid contact. If contact

accidentally occurs, ﬂ ush with water. If liquid contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation or burns.

CAUTION

Do not expose the instrument to the direct sun, high temperature and humidity or dew fall.

Altitude 2000m or less. Appropriate operating temperature is within 14°F and 122°F (-10°C

and 50°C).

This instrument isn’t dust & water proofed. Keep away from dust and water.

Be sure to power o the instrument after use. When the instrument will not be in use for a long

period, place it in storage after removing the batteries.

Use a cloth dipped in water or neutral detergent for cleaning the instrument. Do not use

abrasives or solvents.

4 to 20 mA Span Percentage

22 mA 110%

20 mA 100%

16 mA 75%

12 mA 50%

8 mA 25%

4 mA 0%

0 mA -25%

Range Resolution Accuracy

0.00 mA to 3.99 mA 0.01 mA ± 0.2% ± 10 digits

4.00 mA to 21.49 mA 0.01 mA ± 0.2% ± 5 digits

21.5 mA to 99.9 mA 0.1 mA ± 1.0% ± 5 digits

OPERATION

ASSEMBLY

SYMBOLOGY

Changing the Batteries

To avoid false readings, replace batteries as soon

as the low battery indicator

is displayed.

1. Turn the meter OFF and remove the clamp from

the conductor..

2. Unscrew and re-

move battery door.

3. Insert two (2) AA

batteries, accord-

ing to the polarity

marked in the bat-

tery compartment

4. Close the battery

door and tighten

screw securely.

WARNING

To avoid an electrical hazard, turn the meter

OFF and remove the clamp from the conduc-

tor before replacing batteries.

Read Operator’s Manual

Volts

Direct Current

Double Insulation

Do not apply around or remove from

HAZARDOUS LIVE conductors.

Danger, Warning, or Caution

Battery

European Conformity Mark

Underwriters Laboratories, Inc.,

United States and Canada

1Canadian Conformity Mark

Cat II Classiﬁ cation of transient over-

voltages, based on nominal line

voltage to earth.

Do not dispose of this product as

unsorted municipal waste. Contact

qualiﬁ ed recycler for disposal.

DANGER To avoid electrical shock:

Use only for tests on 60V Cat II DC circuits.

Do not use to test AC current.

Do not make tests on non-insulated con-

ductors.

Do not use with the battery cover removed.

CAUTION Maximum conductor size

is 0.23" (6 mm) diameter. During mea-

surement, keep the jaws fully closed to ensure

accurate measurements.

Measuring

1. Remove the clamp

from the clamp storage

pocket.

2. Press the power button

to turn on the meter. Al-

ways press the ZERO

button before placing

the clamp around a

conductor to take a

new measurement.

3. Keep ﬁ ngers behind

tactile barrier.

4. Open the jaws and clamp them around the con-

ductor under test.

NOTE: Do not clamp over more than one wire

at a time. Irregular results will occur.

5. The reading is displayed. A negative number

indicates current ﬂ ow in the opposite direction

of the arrows on the clamp.

6. Press the power button to turn off the meter.

Remove the jaws from the conductor.

Worklight LED Button

To turn the worklight on and off, press the

button.

ZERO Button

Always press the ZERO button before clamping

around a conductor. Pressing the ZERO button

removes the residual DC current oset to ensure

a more accurate reading.

HOLD Button

Press the HOLD button to freeze the reading. The

reading will be held regardless of subsequent varia-

tion in input. HOLD is displayed with the reading.

To exit Hold mode, press the HOLD button again.

Sleep Mode

The display will turn o about 5 minutes after the

last button operation to conserve battery life. Press

any button to turn the display back on.

Auto Power O

The meter will completely power off about 15

minutes after the last button operation to conserve

battery life.

1.5V

FIVE YEAR TOOL LIMITED

WARRANTY

MILWAUKEE Test & Measurement Product (including

bare tool, M12™ battery pack(s) and battery charger)

is warranted to the original purchaser only to be free

from defects in material and workmanship. Subject to

certain exceptions, MILWAUKEE will repair or replace

any part on this product which, after examination, is

determined by MILWAUKEE to be defective in material

or workmanship for a period of ﬁ ve (5) years* after the

date of purchase. Return of the Test & Measurement

tool to the nearest Milwaukee Electric Tool Corporation

- factory Service Center, freight prepaid and insured

is required. A copy of the proof of purchase should be

included with the return product. This warranty does not

apply to damage that MILWAUKEE determines to be

from repairs made or attempted by anyone other than

MILWAUKEE authorized personnel, misuse, alterations,

abuse, normal wear and tear, lack of maintenance, or

accidents.

* See separate & distinct CORDLESS BATTERY PACK

LIMITED WARRANTY statement for the warranty period

of the LITHIUM-ION battery pack that ships with Test &

Measurement Product. *Alkaline battery that ships with

Test & Measurement Product is separately warranted

by the alkaline battery manufacturer.

*The warranty period for a Voltage Detector with Work

Light – 2201 20, Voltage Detector with LED – 2202-20

or M12™ 2-Beam Plumb Laser – 2230 20 is one (1)

year from the date of purchase.

Warranty Registration is not necessary to obtain the ap-

plicable warranty on MILWAUKEE product. The manu-

facturing date of the product will be used to determine

the warranty period if no proof of purchase is provided

at the time warranty service is requested.

ACCEPTANCE OF THE EXCLUSIVE REPAIR AND

REPLACEMENT REMEDIES DESCRIBED HEREIN

IS A CONDITION OF THE CONTRACT FOR THE

PURCHASE OF EVERY MILWAUKEE PRODUCT. IF

YOU DO NOT AGREE TO THIS CONDITION, YOU

SHOULD NOT PURCHASE THE PRODUCT. IN NO

EVENT SHALL MILWAUKEE BE LIABLE FOR ANY

INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNI-

TIVE DAMAGES, OR FOR ANY COSTS, ATTORNEY

FEES, EXPENSES, LOSSES OR DELAYS ALLEGED

TO BE AS A CONSEQUENCE OF ANY DAMAGE TO,

FAILURE OF, OR DEFECT IN ANY PRODUCT IN-

CLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR

LOSS OF PROFITS. SOME STATES DO NOT ALLOW

THE EXCLUSION OR LIMITATION OF INCIDENTAL

OR CONSEQUENTIAL DAMAGES, SO THE ABOVE

LIMITATION OR EXCLUSION MAY NOT APPLY TO

YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU

OF ALL OTHER WARRANTIES, WRITTEN OR ORAL.

TO THE EXTENT PERMITTED BY LAW, MILWAUKEE

DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING

WITHOUT LIMITATION ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICU-

LAR USE OR PURPOSE; TO THE EXTENT SUCH

DISCLAIMER IS NOT PERMITTED BY LAW, SUCH

IMPLIED WARRANTIES ARE LIMITED TO THE DURA-

TION OF THE APPLICABLE EXPRESS WARRANTY

AS DESCRIBED ABOVE. SOME STATES DO NOT

ALLOW LIMITATIONS ON HOW LONG AN IMPLIED

WARRANTY LASTS, SO THE ABOVE LIMITATION

MAY NOT APPLY TO YOU, THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO

HAVE OTHER RIGHTS WHICH VARY FROM STATE

TO STATE.

This warranty applies to product sold in the U.S.A. and

Canada only.

MAINTENANCE

WARNING To reduce the risk of per-

sonal injury and damage, never immerse your

tool in liquid or allow a liquid to ﬂ ow inside it.

WARNING To reduce the risk of injury,

always remove the batteries from the tool

before performing any maintenance. Never

disassemble the tool. Contact a MILWAUKEE

service facility for ALL repairs.

Cleaning

Clean dust and debris from tool. Keep tool clean, dry

and free of oil or grease. Use only mild soap and a

damp cloth to clean the tool since certain cleaning

agents and solvents are harmful to plastics and other

insulated parts. Some of these include gasoline,

turpentine, lacquer thinner, paint thinner, chlorinated

cleaning solvents, ammonia and household deter-

gents containing ammonia. Never use ﬂ ammable or

combustible solvents around tools.

Repairs

For repairs, return the tool to the nearest service

center listed on the back cover of this operator's

manual.

Maintaining Tool

Keep your tool in good repair by adopting a regular

maintenance program. After six months to one year,

depending on use, return the tool to a MILWAUKEE

service facility for repairs.

If the tool does not start or operate at full power

with new batteries, clean the contacts on the battery

door. If the tool still does not work properly, return

the tool to a service facility for repairs.MILWAUKEE

ACCESSORIES

For a complete listing of accessories refer to your

MILWAUKEE Electric Tool catalog or go online

to www.milwaukeetool.com. To obtain a catalog,

contact your local distributor or service center.

WARNING Always remove batteries be-

fore changing or removing accessories. Only

use accessories speciﬁ cally recommended

for this tool. Others may be hazardous.

Product specificaties

Merk:	Milwaukee
Categorie:	Meetapparatuur
Model:	2231-20

Heb je hulp nodig?

Als je hulp nodig hebt met Milwaukee 2231-20 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Meetapparatuur Milwaukee

Milwaukee 2225-20 Handleiding

19 November 2024

Milwaukee Digital Level Handleiding

3 April 2024

Milwaukee 2200-40 Handleiding

19 Maart 2024

Milwaukee 2216-40 Handleiding

19 Maart 2024

Milwaukee 2235-40 Handleiding

18 Maart 2024

Milwaukee 2205-40 Handleiding

18 Maart 2024

Milwaukee 2217-40 Handleiding

18 Maart 2024

Milwaukee 2231-20 Handleiding

16 April 2023

Handleiding Meetapparatuur

Nieuwste handleidingen voor Meetapparatuur

Hazet 4650-5 Handleiding

24 December 2024

Einhell TE-LL 360 G Handleiding

23 December 2024

TFA 40.1001 Handleiding

21 December 2024

Ansmann Comfort Check Handleiding

20 December 2024

PCE Instruments PCE-PST 1 X Handleiding

16 December 2024

Steinberg SBS-LF-147 Handleiding

15 December 2024

Steinberg SBS-SM-135C Handleiding

15 December 2024

Steinberg SBS-MT-100 Handleiding

15 December 2024

Steinberg SBS-SM-130C Handleiding

15 December 2024

Steinberg SBS-DT-999 Handleiding

15 December 2024