Milan CPSMC0200-210 Handleiding

Milan Niet gecategoriseerd CPSMC0200-210

Lees hieronder de 📖 handleiding in het Nederlandse voor Milan CPSMC0200-210 (5 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/5

User’s Guide

CPSMC0200-2x0

Dual-Slot PointSystem™

Chassis

The Transition Networks CPSMC0200-

2x0 series dual-slot PointSystem™

chassis is designed for installation of

one or two selectable Transition

Networks mediaPointSystem™

converter slide-in modules.

Installation . . . . . . . . . . . . . . . . . . . . .2

Technical Specifications . . . . . . . . . . .4

Troubleshooting . . . . . . . . . . . . . . . .5

Compliance Information . . . . . . . . . .6

Part Number Description

CPSMC0200-200 Dual-Slot PointSystem™ chassis intended for installation of any

PointSystem™ media converter slide-in modules.

CPSMC0200-210 Dual-Slot PointSystem™ chassis intended for installation of any

PointSystem™ media converter slide-in modules. Also provides

a Last Gasp trap generation.

Optional Accessories (sold separately)

Part Number Description

SPS-1872-SA Optional External Power Supply; 18-72VDC Stand-Alone

Output: 12.6VDC, 1.0 A

WMBP Optional Wall Mount Bracket; Length: 5.0 in. (127 mm)

WMBV Optional Vertical Mount Bracket; 5.0 in. (127 mm)

WMBD Optional DIN Rail Mount Bracket; 5.0 in. (127 mm)

224-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

CPSMC0200-200 / CPSMC0200-210

Installation

Installing a slide-in module

CAUTION: Do NOT install Two (2) PointSystem™ media converter slide-in

modules whose total power requirements exceed 12 W (with a maximum of 6 W per

slot). Failure to observe this caution could cause data transfer to fail and also could

result in damage to, and subsequent failure of, the media converter slide-in module.

CAUTION: Wear a grounding device and observe electrostatic discharge

precautions when installing the media converter slide-in module in to the dual-slot

chassis. Failure to observe this caution could result in damage to, and subsequent

failure of, the media converter slide-in module.

NOTE: If only one slide-in module is to be installed into the dual-slot chassis,

ensure network standards compliance by obtaining a custom faceplate

(P/N CPSFP-200) from Transition Networks for installation into the

second, unused slot.

To install a slide-in module into the dual-slot chassis:

1. Refer to the user’s guide that comes with the slide-in module to ensure that any

switches or jumpers on the slide-in module circuit board are set correctly for

the site installation.

2. Carefully align the slide-in module with the chassis installation guides and

slide the module into the installation slot.

3. Ensure that the slide-in module is firmly seated inside the chassis.

4. Push in and rotate the attached panel faster screw clockwise to secure the slide-

in module to the chassis front.

5. Repeat steps 1-4 for the second slide-in module.

Panel Fastener

techsupport@transition.com “Transition Now”-- Click the link for a live Web chat. 3

Installation -- Continued

Power the Chassis

To supply AC power to the dual-slot chassis:

1. Locate an appropriate 12 volt power adapter for the installed media converter

slide-in module(s).

2. Connect the barrel connector on the power adapter to the dual-slot chassis

power port (located on the back of the chassis).

3. Connect the power adapter plug to AC power.

4. Verify that the dual-slot chassis is powered by observing the illuminated

LED(s) on the installed slide-in module(s).

To supply DC power to the dual-slot chassis:

Consult the user’s guide for the Transition Networks SPS1872-xx DC external

power supply for powering the dual-slot chassis.

Last Gasp Option (CPSMC0200-210 model only)

The CPSMC0200-210 model features the Last Gasp option, which enables the

device to send out an SNMP trap to the device in the event of a power failure;

alerting the management console that the device has failed.

424-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

CPSMC0200-200 / CPSMC0200-210

Installation -- Continued

Grounding the Media Converter

The dual-slot chassis comes equipped with grounding lugs located on the back

panel. They require a grounding conductor wire terminated with a two-hole,

compression-type, grounding connector. The grounding wire -- which must be a

copper conductor -- is not included with the chassis and must be provided by the

customer/installer.

The electrical conducting path from the single-slot chassis must:

• Flow via the grounding lugs to the common bonding network (CBN) for

telecom installations, or to an alternative approved grounding system (if

required) for non-telecom installations.

• Be of sufficiently low impedance to conduct fault currents likely to be imposed

on the media converter, and

• Enable proper operation of any over-current protection devices.

The conductor must be fastened to the grounding lugs with the enclosed anti-

rotation star-washers and lug-nut fasteners. The applied torque required to the

connector lug-nut fasteners is specified by the connector’s manufacturer.

To properly ground the dual-slot chassis:

1. Obtain one (1) grounding conductor (12 AWG copper wire gauge or larger)

with a two-hole, compression-type, grounding connector.

2. Attach the grounding conductor to the converter by placing the two-hole

connector onto the grounding lugs and fasten with the enclosed lock-washers /

lug-nuts at the proper torque (per

the manufacturer’s

specification).

3. Attach the opposite end of the

grounding conductor to the

common bonding network (CBN)

for telecom, or to earth ground (if

required) for non-telecom

installations.

grounding

lugs

grounding

connector

and wire

earth ground

3/4-inch

spacing

Grounding lugs

(6-32, 1/8" diam.)

12 AWG copper wi

(not included)

Star washer (included)

Lug nuts (included)

wo-hole, compression-type

grounding connector

(not included)

techsupport@transition.com -- Click the “Transition Now” link for a live Web chat. 5

Technical Specifications

For use with Transition Networks Model CPSMC0200-2x0 or equivalent.

NOTE: The CPSMC0200-2x0 dual-slot chassis is Class B compliant ONLY if Class

B-compliant media converters are installed. Installation of a Class A-

compliant media converter reduces the chassis to Class A compliance.

The maximum power delivery capacity for each chassis slot is 12 Watts with an

aggregate chassis maximum of 6 W per slot. Example: A 9-Watt media converter

would require the power of both slots. In this example, the second slot must remain

unused.

Compliance EN55022; Class A&B; CE Mark

Dimensions 5.4 x 5.6 x 2.2 in (137 x 142 x 56 mm)

Weight 1.4 lb. (0.6 kg.) (approximate)

MTBF (CPSMC0200-200) Greater than 67,900 hours (MIL-HDBK-217F)

Greater than 186,900 hours (Bellcore7 V5.0)

with Powr Supply Greater than 50,700 hours (MIL-HDBK-217F)

Greater than 139,500 hours (Bellcore7 V5.0)

MTBF (CPSMC0200-210) Greater than 60,600 hours (MIL-HDBK-217F)

Greater than 183,200 hours (Bellcore7 V5.0)

with Powr Supply Greater than 49,900 hours (MIL-HDBK-217F)

Greater than 137,400 hours (Bellcore7 V5.0)

Power Supply 12VDC, 1.25 A; 100-240 VAC

Environment Tmra*: 0 to 60°C (32 to 140° F)

Storage Temp: -20 to 85°C

Humidity: 10 to 90%, non condensing

Warranty Lifetime

*Manufacturer’s rated ambient temperature for the dual-slot chassis. Refer to the

user’s guide of the installed media converter for its operating temperature range.

The information in this user’s guide is subject to change. For the most up-to-date

information on the CPSMC0100-20x dual-slot chassis, view the user’s guide on-line

at: www.transition.com.

Product specificaties

Merk:	Milan
Categorie:	Niet gecategoriseerd
Model:	CPSMC0200-210

Heb je hulp nodig?

Als je hulp nodig hebt met Milan CPSMC0200-210 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Milan

Milan SESPM-4P-PMB Handleiding

13 Februari 2024

Milan CPSMC0200-210 Handleiding

13 Februari 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

GolfBuddy GB LASER 1 Handleiding

24 November 2024

GoGEN DRZAKOLEDFM Handleiding

24 November 2024

Cambridge Alva Duo Handleiding

24 November 2024

GoGEN DRZAKTILTXL Handleiding

24 November 2024

GoGEN DRZAKOLEDTM Handleiding

24 November 2024

GoGEN DRZAKSBM Handleiding

24 November 2024

GoGEN DRZAKTILTL Handleiding

24 November 2024

GoGEN DRZAKSBL Handleiding

24 November 2024

Tiger JCC-270P Handleiding

24 November 2024

GolfBuddy aim L10V Handleiding

24 November 2024