Mikrotik PWR-Line AP Handleiding

Mikrotik Powerline adapter PWR-Line AP

Lees hieronder de 📖 handleiding in het Nederlandse voor Mikrotik PWR-Line AP (4 pagina's) in de categorie Powerline adapter. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

PWR-LINE AP

The PWR-LINE series devices allow Ethernet like connectivity between supported devices over regular electrical

power lines. When plugged into the same electrical circuit, the PWR devices will establish Ethernet connectivity by

using the HomePlug AV standard.

The PWR-LINE AP is a wireless access point with a single Ethernet port, a built-in 802.11b/g/n WiFi Access Point

and integrated PWR-LINE support.

Simply plug this device directly into one of the LAN ports of your MikroTik router, and add another supported device

somewhere further in your premises, allowing to extend wireless network coverage without needing to install any

LAN cables. You can install more PWR-LINE devices to further build your network.

Connecting

1. Plug one PWR-LINE AP device into a power socket.

2. The main device should be plugged into one of the LAN ports of a router.

3. Other PWR-LINE AP devices can be placed anywhere in any sockets in the same power circuit.

4. Use Winbox “Neighbors” tab to discover the addresses of the PWR LINE units.

5. Since there is no password by default, you will be logged in automatically. Set up your wifi password and

your country, to make sure local regulations are observed.

6. To add more devices that will connect over the electrical lines, add compatible devices somewhere in the

same electrical circuit. See section Buttons and Jumpers on how to pair individual PWR-LINE devices.

Important note! The device is configured as a bridge, for extending your LAN network. By default, it does not have

a password or firewall, and should not be connected directly to the internet, without configuring it accordingly.

RouterOS includes many configuration options in addition to what is described in this document. We suggest to

start here to get yourself accustomed to the possibilities: http://mt.lv/help

In case IP connection is not available, the Winbox tool ( ) can be used to connect to the MAC http://mt.lv/winbox

address of the device from the LAN side (all access is blocked from the internet port by default).

For recovery purposes, it is possible to boot the device from network, see section Buttons and Jumpers.

Powering

The device accepts powering directly from 100-240 V ~50/60Hz wall socket it is plugged into. The power

consumption under maximum load can reach 7 W.

Extension Slots and Ports

One 10/100 Ethernet port, supporting automatic cross/straight cable correction (Auto MDI/X), so you can

use either straight or cross-over cables for connecting to other network devices.

Integrated Wireless 2.4 GHz 802.11b/g/n with onboard PIF antennas, max gain 1.5 dBi.

See for more information. Contact for help. Document #43270, Modified on 05/30/18https://mikrotik.com support@mikrotik.com

Buttons and Jumpers

The PWR-LINE AP has the following buttons:

Reset button

•Hold the button before powering on the device, and at power up, the button will force load the backup boot

loader. Continue holding the button for the other two functions of this button.

•Release the button when green LED starts flashing, to reset RouterOS configuration. To not load backup

boot loader, you can start holding the button after power is already applied.

•Release the button after LED is no longer flashing (~20 seconds) to cause device to look for Netinstall

servers (required for reinstalling RouterOS over network).

Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is

pressed before power is applied to the device. Useful for RouterBOOT debugging and recovery.

Sync button

•Hold 0.5 – 3 seconds. For 120 seconds will try to communicate with another PWR-LINE device. A blinking

orange LED light indicates that it is in search mode. You have to also do the same on the other PWR

device, so they can synchronize. Press button again to cancel the search. You can also manually set the

security keys in RouterOS settings.

•Hold 5 – 8 seconds. A new security key is generated. This is needed to remove a PWR-LINE device from

an existing PWR network.

•Hold 10 – 15 seconds. Resets all PWR related settings.

Mode button

This button can be configured from RouterOS software to execute any user supplied RouterOS script. You can also

disable this button.

Operating system support

The device supports RouterOS software with the version number at or above what is indicated in the RouterOS

menu . Other operating systems have not been tested. /system resource

See for more information. Contact for help. Document #43270, Modified on 05/30/18https://mikrotik.com support@mikrotik.com

Federal Communication Commission Interference Statement

FCC ID: TV7PL64112ND

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could

void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.This device and its antenna must not be co-located or operation in

conjunction with any other antenna or transmitter.

IMPORTANT: Exposure to Radio Frequency Radiation. 20 cm minimum distance has to be maintained between the

antenna and user. Under such configuration, the FCC radiation exposure limits set forth for an

population/uncontrolled environment can be satisfied.

Antenna Installation. WARNING: It is installer's responsibility to ensure that when using the authorized antennas in

the United States (or where FCC rules apply); only those antennas certified with the product are used. The use of

any antenna other than those certified with the product is expressly forbidden in accordance to FCC rules CFR47

part 15.204. The installer should configure the output power level of antennas, according to country regulations and

per antenna type. Professional installation is required of equipment with connectors to ensure compliance with

health and safety issues.

Industry Canada

IC: 7442A-PL64112ND

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following

two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,

including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.

L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)

l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en

compromettre le fonctionnement.

See for more information. Contact for help. Document #43270, Modified on 05/30/18https://mikrotik.com support@mikrotik.com

Product specificaties

Merk:	Mikrotik
Categorie:	Powerline adapter
Model:	PWR-Line AP
Kleur van het product:	Wit
Breedte:	50 mm
Diepte:	33 mm
Hoogte:	68 mm
Type stekker:	Type C
LED-indicatoren:	Ja
Inclusief besturingssysteem:	RouterOS
Frequentieband:	2.4 GHz
Aantal Ethernet LAN (RJ-45)-poorten:	1
Vermogensverbruik (max):	7 W
Intern geheugen:	64 MB
Type processor:	Ja
Gevoeligheid ontvanger:	1MBit/s\t22dBm\t-96dBm\n11MBit/s\t22dBm\t-89dBm\n6MBit/s\t20dBm\t-93dBm\n54MBit/s\t18dBm\t-74dBm\nMCS0\t20dBm\t-93dBm\nMCS7\t16dBm\t-71dBm
Ethernet LAN, data-overdrachtsnelheden:	10, 100 Mbit/s
Netwerkstandaard:	IEEE 802.11b, IEEE 802.11g, IEEE 802.11n
Antenne versterkingsniveau (max):	1.5 dBi
Intern:	Nee
Flash memory:	16 MB
Maximale overdrachtssnelheid van gegevens:	300 Mbit/s
2,4 GHz:	Ja
5 GHz:	Nee
Antennefuncties:	Ingebouwde antenne
Zendvermogen:	22 dBmW
Bedrijfstemperatuur (T-T):	-20 - 60 °C