Metra TE-SRBC Handleiding

Metra Dashcam TE-SRBC

Lees hieronder de 📖 handleiding in het Nederlandse voor Metra TE-SRBC (2 pagina's) in de categorie Dashcam. Deze handleiding was nuttig voor 41 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
TE-SRBC
Product Manual
TE-SRBC
Product Manual
800.221.0932
iBeamUSA.com
460 Walker Street, Holly Hill, FL 32117
800.221.0932
iBeamUSA.com
460 Walker Street, Holly Hill, FL 32117
1) Find a suitable location to surface mount install the camera. Make sure the
camera’s view is unobstructed and be careful not to drill into any wires that
might damage the vehicle. When all connections have been made and before
mounting the camera, verify the camera is working and has good view of the
area. Then mount the camera down with the supplied two screws.
2) Connect the RED wire to the +12 volt reverse wire
3) Connect the BLACK wire to ground (a metal, non-painted surface).
4) Run video cable though vehicle, up to video display. (Avoid placing video
cable where it can get pinched or damaged).
5) Attach the YELLOW video rca to the reverse camera input of the radio or
video display; connect the RED wire coming from the YELLOW video rca to
the reverse trigger wire on the radio or video display.
NOTE: The camera comes with the parking assist lines and a normal image view
active. If you want to remove the parking lines or change the image to reverse
image, follow the steps below:
A) Disconnect power to the camera
B) Cut the WHITE loop to remove the parking assist lines, isolate and tape the wires
C) Cut the BLUE loop to reverse the image, isolate and tape the wires
D) Reconnect power to the camera
If the parking assist lines are wanted or the image needs to go back to normal,
just follow the steps above and reconnect the wires.
1) Find a suitable location to surface mount install the camera. Make sure the
camera’s view is unobstructed and be careful not to drill into any wires that
might damage the vehicle. When all connections have been made and before
mounting the camera, verify the camera is working and has good view of the
area. Then mount the camera down with the supplied two screws.
2) Connect the RED wire to the +12 volt reverse wire
3) Connect the BLACK wire to ground (a metal, non-painted surface).
4) Run video cable though vehicle, up to video display. (Avoid placing video
cable where it can get pinched or damaged).
5) Attach the YELLOW video rca to the reverse camera input of the radio or
video display; connect the RED wire coming from the YELLOW video rca to
the reverse trigger wire on the radio or video display.
NOTE: The camera comes with the parking assist lines and a normal image view
active. If you want to remove the parking lines or change the image to reverse
image, follow the steps below:
A) Disconnect power to the camera
B) Cut the WHITE loop to remove the parking assist lines, isolate and tape the wires
C) Cut the BLUE loop to reverse the image, isolate and tape the wires
D) Reconnect power to the camera
If the parking assist lines are wanted or the image needs to go back to normal,
just follow the steps above and reconnect the wires.
II. Connection
II. Connection
I. Specifications
I. Specifications
Parking line loop (White)
RED (+)
BLACK (Ground)
Video (in)
Reverse image loop (Blue)
Red (Reverse Switch)
Reverse Wire on Radio (Trigger)
Reverse Lights
TV
Parking line loop (White)
RED (+)
BLACK (Ground)
Video (in)
Reverse image loop (Blue)
Red (Reverse Switch)
Reverse Wire on Radio (Trigger)
Reverse Lights
TV
SENSOR
Effective Pixel
Horizontal Sync Frequency
Vertical Sync Frequency
Scanning System
Sync System
AGC
BLC
Resolution
S/N Ratio
Current Consumption
Power Supply
Operating Temperature
Storage Tempurature
Viewing Angle
Water-Proof
Minimum Illumination
SENSOR
Effective Pixel
Horizontal Sync Frequency
Vertical Sync Frequency
Scanning System
Sync System
AGC
BLC
Resolution
S/N Ratio
Current Consumption
Power Supply
Operating Temperature
Storage Tempurature
Viewing Angle
Water-Proof
Minimum Illumination
CMOS II
656 X 492
15625KHZ
PAL50HZ / NTSC 60HZ
2 : 1 Interlace
Internal
Auto
Auto
420 TV Lines
More Than 48dB
No More 150mA
DC12V ± 10%
-22° ~ 176° F
-40° ~ 176° F
170°
IP67
0.5Lux/F1.2(0Lux with LED)
CMOS II
656 X 492
15625KHZ
PAL50HZ / NTSC 60HZ
2 : 1 Interlace
Internal
Auto
Auto
420 TV Lines
More Than 48dB
No More 150mA
DC12V ± 10%
-22° ~ 176° F
-40° ~ 176° F
170°
IP67
0.5Lux/F1.2(0Lux with LED)

Product specificaties

Merk: Metra
Categorie: Dashcam
Model: TE-SRBC

Heb je hulp nodig?

Als je hulp nodig hebt met Metra TE-SRBC stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Dashcam Metra

Metra

Metra TE-RMH Handleiding

8 Juli 2023
Metra

Metra TE-CCM1 Handleiding

6 Juli 2023
Metra

Metra TE-3BMC Handleiding

5 Juli 2023
Metra

Metra TE-2PSK Handleiding

5 Juli 2023
Metra

Metra JP-JLKT Handleiding

5 Juli 2023
Metra

Metra TE-FDH Handleiding

30 Juni 2023
Metra

Metra TE-FDHDH Handleiding

30 Juni 2023
Metra

Metra TE-FDFTG Handleiding

29 Juni 2023
Metra

Metra TE-SRBC Handleiding

28 Juni 2023
Metra

Metra TE-TUTGC Handleiding

28 Juni 2023

Handleiding Dashcam

Nieuwste handleidingen voor Dashcam

Minolta

Minolta MNCD355X Handleiding

21 November 2024
Minolta

Minolta MNCD337N Handleiding

21 November 2024
Minolta

Minolta MNCD2K10 Handleiding

21 November 2024
Cowon

Cowon AW1 Auto Capsule Handleiding

17 November 2024
Xblitz

Xblitz S8 Handleiding

15 November 2024
Mio

Mio MiVue C595W Handleiding

6 November 2024
Mio

Mio MiVue C595WD Handleiding

6 November 2024
Mio

Mio MiVue J30 Handleiding

6 November 2024
Uniden

Uniden iGO CAM 445 Handleiding

2 November 2024
AZDome

AZDome M300S Handleiding

2 November 2024