Metra LC-CHRC-01 Handleiding

Metra Niet gecategoriseerd LC-CHRC-01

Lees hieronder de 📖 handleiding in het Nederlandse voor Metra LC-CHRC-01 (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/8
LC-CHRC-01
I N S TA L L AT I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 9/30/19 INSTLC-CHRC-01
Product Info
INTERFACE FEATURES
INTERFACE COMPONENTS
TOOLS REQUIRED
• Wire cutter • Crimp tool • Solder gun • Tape
• Connectors (example: butt-connectors, bell
caps, etc.)
TABLE OF CONTENTS
Connections ............................................................2
Installation .............................................................3
Programming .........................................................3
Ram Data Interface 2013-2017
• Provides accessory power (12-volt 10-amp)
• Retains R.A.P. (retained accessory power)
• Used in non-amplified models, or when bypassing a factory amplifier
• Provides NAV outputs (parking brake, reverse, and speed sense)
• Pre-wired ASWC-1 harness (ASWC-1 sold separately)
•
Retains the factory backup camera (if displayed through the OE radio)
• Retains the 3.5mm AUX-IN jack
• Retains balance and fade
• Retains safety chimes
• Micro-B USB updatable
• LC-CHRC-01 interface
• LC-CHRC-01 harness
APPLICATIONS
RAM
1500/2500/3500
(small screen option) 2013-2017
Chassis Cab 3500/4500/5500
(small screen option) 2013-2017
2
CONNECTIONS
From the LC-CHRC-01 harness to the aftermarket radio:
• Connect the wire to the ground wire.Black
• Connect the Yellow wire to the battery wire.
• Connect the wire to the accessory wire.Red
• If the aftermarket radio has an illumination wire, connect the wire to it.Orange
• Connect the wire to the right front positive speaker output.Gray
• Connect the Gray/Black wire to the right front negative speaker output.
• Connect the wire to the left front positive speaker output.White
• Connect the wire to the left front negative speaker output.White/Black
• Connect the wire to the left rear positive speaker output.Green
• Connect the wire to the left rear negative speaker output.Green/Black
• Connect the wire to the right rear positive speaker output.Purple
• Connect the wire to the right rear negative speaker output.Purple/Black
The following (3) wires are only for multimedia/navigation radios that require these wires.
• Connect the wire to the VSS/speed sense wire.Blue/Pink
• Connect the wire to the reverse wire.Green/Purple
• Connect the wire to the parking brake wire.Light Green
• Connect the Yellow RCA jack the backup camera input.
• If retaining the factory AUX-IN jack, connect the & RCA jacks to the AUX input.Red White
• Tape off and disregard the wire, it will not be used in this application.Blue/White
12-pin pre-wired ASWC-1 harness:
• This harness is to be used along with the optional ASWC-1 (not included) to retain steering
wheel audio controls. If the ASWC-1 is not being used, disregard this harness. If it will be
used, please refer to the ASWC-1 instructions for radio connections and programming.
Note: Disregard the harness that comes with the ASWC-1.
• Connect the wire to the accessory wire.Red
3
REV. 9/30/2019 INSTLC-CHRC-01
INSTALLATION PROGRAMMING
With the key in the off position:
• Connect the LC-CHRC-01 harness into the interface, and then to the harness in the vehicle.
If using the ASWC-1, connect it after you initialize and test the LC-CHRC-01, with the key Note:
in the off position.
Attention!
If the interface loses power for any reason, the following steps will need to be
performed again. Also, if installing an ASWC-1 connect it after you initialize and test the interface/
radio, with the key in the off position.
• Turn the key (or push-to-start button) to the ignition position and wait until the radio comes on
.
If the radio does not come on within 60 seconds, turn the key to the off position, Note:
disconnect the interface, check all connections, reconnect the interface, and then try again.
• Turn the key to the off position, and then to the accessory position. Test all functions of the
installation for proper operation, before reassembling the dash.

Product specificaties

Merk: Metra
Categorie: Niet gecategoriseerd
Model: LC-CHRC-01

Heb je hulp nodig?

Als je hulp nodig hebt met Metra LC-CHRC-01 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Metra

Metra

Metra 95-7022HG Handleiding

12 November 2024
Metra

Metra 95-7642 Handleiding

12 November 2024
Metra

Metra 71-017C Handleiding

26 September 2024
Metra

Metra AXSP-HK Handleiding

26 September 2024
Metra

Metra 109-TO7 Handleiding

24 September 2024
Metra

Metra 95-8273B Handleiding

6 September 2024
Metra

Metra 95-7822 Handleiding

6 September 2024
Metra

Metra 82-8703 Handleiding

6 September 2024
Metra

Metra 88-00-9004 Handleiding

6 September 2024
Metra

Metra 82-9101 Handleiding

6 September 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Livarno Lux

Livarno Lux IAN 071407 Handleiding

29 November 2024
Livarno Lux

Livarno Lux IAN 317128 Handleiding

29 November 2024
Livarno Lux

Livarno Lux IAN 049213 Handleiding

29 November 2024
Livarno Lux

Livarno Lux ST-1002 Handleiding

29 November 2024
Livarno Lux

Livarno Lux HG02489 Handleiding

29 November 2024
Livarno Lux

Livarno Lux HG02189 Handleiding

29 November 2024
Livarno Lux

Livarno Lux IAN 365198 Handleiding

29 November 2024
Livarno Lux

Livarno Lux IAN 367074 Handleiding

29 November 2024
Livarno Lux

Livarno Lux HG00701 Handleiding

29 November 2024
Livarno Lux

Livarno Lux IAN 337273 Handleiding

29 November 2024