Metra LC-BMRC-01 Handleiding

Metra Niet gecategoriseerd LC-BMRC-01

Lees hieronder de 📖 handleiding in het Nederlandse voor Metra LC-BMRC-01 (5 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/5

Installation instructions for part LC-BMRC-01

REV. 5/13/2016 INSTLC-BMRC-01

Axxess Integrate

CAUTION!

All accessories, switches, climate controls panels, and

especially air bag indicator lights must be connected before cycling

the ignition. Also, do not remove the factory radio with the key in the

on position, or while the vehicle is running.

• Provides accessory power (12-volt 10-amp)

• Retains R.A.P. (retained accessory power)

• Provides NAV outputs (parking brake, reverse, and V.S.S)

• Retains warning chimes

• For non-amplified models, or when bypassing a factory amplifier

• Retains balance and fade

• Micro “B” USB updatable

FEATURES

• Wire cutter • Crimp tool • Solder gun • Tape

• Connectors (example: butt-connectors, bell caps, etc.)

TOOLS REQUIRED

LC-BMRC-01

BMW / Mini Chime Retention

2006-2015

APPLICATIONS

• LC-BMRC-01 interface • LC-BMRC-01 harness

• Fuse holder with 96” length of wire

INTERFACE COMPONENTS

BMW

1 Series (without amp) 2008-2013

3 Series (without amp) 2006-2013

M3 (without amp) 2007-2013

MINI

Cooper (without amp) 2007-2015

Connections to be made ................................................... 2

Installing the LC-BMRC-01 ............................................... 3

Initializing the LC-BMRC-01 ............................................. 3

TABLE OF CONTENTS

LC-BMRC-01

From the LC-BMRC-01 harness to the aftermarket radio:

• Connect the Black wire to the ground wire.

• Connect the Yellow wire to the fuse holder with 96” length of wire:

• Remove the fuse from the fuse holder.

• Connect the 6” long wire side of the fuse holder to the vehicles battery.

• Connect the 96” long wire side of the fuse holder to the Yellow wire.

• Connect the Red wire to the accessory wire.

• Connect the Blue wire to the power antenna wire.

• If the aftermarket radio has an illumination wire, connect the wire to it.Orange

• Connect the Gray wire to the right front positive speaker output.

• Connect the Gray/Black wire to the right front negative speaker output.

• Connect the White wire to the left front positive speaker output.

• Connect the White/Black wire to the left front negative speaker output.

• Connect the Green wire to the left rear positive speaker output.

• Connect the Green/Black wire to the left rear negative speaker output.

• Connect the Purple wire to the right rear positive speaker output.

• Connect the Purple/Black wire to the right rear negative speaker output.

The following (3) wires are only for multimedia/navigation radios that require these

wires.

• Connect the Blue/Pink wire to the VSS/speed sense wire.

• Connect the Green/Purple wire to the reverse wire.

• Connect the Light Green wire to the parking brake wire.

12-pin pre-wired ASWC-1 harness:

• This harness is to be used along with the optional ASWC-1 (not included) to

retain steering wheel audio controls. If the ASWC-1 is not being used, disregard

this harness. If it will be used, please refer to the ASWC-1 instructions for radio

connections and programming.

Note: Disregard the harness that comes with the ASWC-1.

Connections to be made

LC-BMRC-01

Installing the LC-BMRC-01

With the key in the off position:

• Connect the LC-BMRC-01 harness into the interface, and then to the vehicle.

• Re-insert the fuse back into the fuse holder.

Attention! If the interface loses power for any reason, the following steps will need

to be performed again. Also, if installing an ASWC-1 connect it after you initialize

and test the interface/radio, with the key in the off position.

• Turn the key (or push-to-start button) to the ignition position and wait until the

radio comes on.

Note: If the radio does not come on within 60 seconds, turn the key to the

off position, disconnect the interface, check all connections, reconnect the

interface, and then try again.

• Turn the key to the off position, and then to the accessory position. Test all

functions of the installation for proper operation, before reassembling the dash.

Initializing the LC-BMRC-01

Product specificaties

Merk:	Metra
Categorie:	Niet gecategoriseerd
Model:	LC-BMRC-01

Heb je hulp nodig?

Als je hulp nodig hebt met Metra LC-BMRC-01 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Metra

Metra 95-7022HG Handleiding

12 November 2024

Metra 95-7642 Handleiding

12 November 2024

Metra 71-017C Handleiding

26 September 2024

Metra AXSP-HK Handleiding

26 September 2024

Metra 109-TO7 Handleiding

24 September 2024

Metra 95-8273B Handleiding

6 September 2024

Metra 95-7822 Handleiding

6 September 2024

Metra 82-8703 Handleiding

6 September 2024

Metra 88-00-9004 Handleiding

6 September 2024

Metra 82-9101 Handleiding

6 September 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024

Kramer K-Bar Camera Bracket Handleiding

26 November 2024

Kramer RK-19 Handleiding

26 November 2024

Kramer OSP-MM1 Handleiding

26 November 2024

Kramer ASPEN-1616UX Handleiding

26 November 2024

Korg Pitchstrap Handleiding

26 November 2024

NeoMounts WL70-450BL11 Handleiding

26 November 2024

Kramer CLS-AOCH/60 Handleiding

26 November 2024

Klauke EKM 6022ISM Handleiding

26 November 2024