Metra HDCC-01 Handleiding

Metra Niet gecategoriseerd HDCC-01

Lees hieronder de 📖 handleiding in het Nederlandse voor Metra HDCC-01 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

HDCC-01

I N S TA L L A T I O N I N S T R U C T I O N S

INTERFACE FEATURES

INTERFACE COMPONENTS

TOOLS REQUIRED

• Crimping tool and connectors, or solder gun,

solder, and heat shrink • Small ﬂat-blade

screwdriver • Tape • Wire cutter • Zip ties

TABLE OF CONTENTS

Connections to be made .......................................2

Installing the HDCC-01............................................3

Programming the HDCC-01 ....................................3

Setting the factory clock .......................................3

Troubleshooting .....................................................3

Honda Clock Retention 2012-2014

APPLICATIONS

• Provides accessory power (12-volt 10-amp)

• Can be used in non-ampliﬁed, or ampliﬁed models

• Provides NAV outputs (parking brake, reverse, speed sense)

• ASWC-1 harness included (ASWC-1 sold separately)

• Retains balance and fade

• Retains the ability to set the factory clock

• Retains the factory AUX-IN jack

• Micro “B” USB updatable

• HDCC-01 interface • HDCC-01 harness

• 8-pin subwoofer harness

• 16-pin harness with stripped leads

HONDA

Civic * (without NAV) 2013 CR-V (without NAV) 2012-2014

* All trims except LX

CONNECTIONS TO BE MADE

From the 16-pin harness with stripped leads to the aftermarket radio:

• Connect the Red wire to the accessory wire.

• Connect the Orange/White wire to the illumination wire. If the aftermarket radio does not

have an illumination wire, tape it off and disregard it.

• Tape off and disregard the Gray Gray/Black White White/Black Brown, , , , and wires, they

will not be used in this application.

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Connect the Light Green wire to the parking brake wire (if applicable).

• Connect the Blue/Pink wire to the VSS or speed sense wire (if applicable).

• Connect the Green/Purple wire to the reverse wire (if applicable).

From the HDCC-01 harness to the aftermarket radio:

• Connect the Black wire to the ground wire.

• Connect the Yellow wire to the battery wire.

• If the vehicle is equipped with a factory ampliﬁer, connect the Blue/White wire to amp

turn-on wire.

• If the vehicle is equipped with a factory AUX-IN jack and desired to be retained, connect the

Red & RCA jacks to the AUX-IN jack.White

For the following (8) wires, if the vehicle does not have a factory ampliﬁer, cut off the RCA jacks

to expose the speaker wires.

• Connect the White wire to the left front positive speaker output.

• Connect the White/Black wire to the left front negative speaker output.

• Connect the Gray wire to the right front positive speaker output.

• Connect the Gray/Black wire to the right front negative speaker output.

• Connect the Green wire to the left rear positive speaker output.

• Connect the Green/Black wire to the left rear negative speaker output.

• Connect the Purple wire to the right rear positive speaker output.

• Connect the Purple/Black wire to the right rear negative speaker output.

From the 8-pin subwoofer harness to the aftermarket radio (ampliﬁed models only):

• Connect the White RCA to the subwoofer output.

12-pin pre-wired ASWC-1 harness:

• This harness is to be used along with the optional ASWC-1 (not included) to retain steering

wheel audio controls. If the ASWC-1 is not being used, disregard this harness. If it will be

used, please refer to the ASWC-1 instructions for radio connections and programming.

Disregard the harness that comes with the ASWC-1.

• For the CR-V 2014: If the vehicle is equipped with Bluetooth controls, and desired to be

retained, connect the Gray/Blue wire to the Yellow wire (pin-15) in the 32-pin harness at the

factory Bluetooth module located in the center of the dash, below the radio.

REV. 7/6/2018 INSTHDCC-01

With the key in the off position:

• Connect the 16-pin harness with stripped leads, and the HDCC-01 harness, into the interface.

• If an ASWC-1 (sold separately) will be used, do not connect it until the HDCC-01 is

programmed and fully functional.

Attention! Do not connect the HDCC-01 harness to the wiring harness in the vehicle just yet.

For the steps below, the L.E.D. located inside the interface can only be seen while active. The

interface does not need to be opened to see the L.E.D.

1. Start the vehicle.

2. Connect the HDCC-01 harness to the wiring harness in the vehicle. The L.E.D. will initially be

Green to indicate the interface is powered.

3. After a few seconds the L.E.D. will turn on solid Red while the interface automatically

programs to the vehicle. The radio will shut off at this point. This process should take 5 to 30

seconds.

4. After the interface is programmed, the L.E.D. will turn on solid Green, and the radio will

come back on, indicating programming was successful.

5. Test all functions of the installation for proper operation, before reassembling the dash.

6. If the interface fails to function, refer to “Troubleshooting”.

Resetting the Axxess interface

1. The Blue reset button is located inside the Axxess interface, between the two connectors.

The button is accessible outside the Axxess interface, no need to open the Axxess interface.

2. Press and hold the reset button for two seconds, then let go to reset the Axxess interface.

3. Refer to “Programming the Axxess Interface” from this point.

The buttons on the steering wheel will be used to set the factory clock.

• Press and hold the SOURCE button on the steering wheel for 15 seconds to access the clock

setting mode.

• Press SEEK-UP or SEEK-DOWN to select hours, minutes, etc. Press VOLUME-UP or

VOLUME-DOWN to set the values.

•

Either press SOURCE again, or wait 5 seconds with no activity to exit the clock setting mode

INSTALLING THE HDCC-01

PROGRAMMING THE HDCC-01 TROUBLESHOOTING

SETTING THE FACTORY CLOCK

Product specificaties

Merk:	Metra
Categorie:	Niet gecategoriseerd
Model:	HDCC-01

Heb je hulp nodig?

Als je hulp nodig hebt met Metra HDCC-01 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Metra

Metra 95-7022HG Handleiding

12 November 2024

Metra 95-7642 Handleiding

12 November 2024

Metra 71-017C Handleiding

26 September 2024

Metra AXSP-HK Handleiding

26 September 2024

Metra 109-TO7 Handleiding

24 September 2024

Metra 95-8273B Handleiding

6 September 2024

Metra 95-7822 Handleiding

6 September 2024

Metra 82-8703 Handleiding

6 September 2024

Metra 88-00-9004 Handleiding

6 September 2024

Metra 82-9101 Handleiding

6 September 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024

Kramer K-Bar Camera Bracket Handleiding

26 November 2024

Kramer RK-19 Handleiding

26 November 2024

Kramer OSP-MM1 Handleiding

26 November 2024

Kramer ASPEN-1616UX Handleiding

26 November 2024

Korg Pitchstrap Handleiding

26 November 2024

NeoMounts WL70-450BL11 Handleiding

26 November 2024

Kramer CLS-AOCH/60 Handleiding

26 November 2024

Klauke EKM 6022ISM Handleiding

26 November 2024