Metra Axxess XSVI-1731-NAV Handleiding

Metra Niet gecategoriseerd Axxess XSVI-1731-NAV

Lees hieronder de 📖 handleiding in het Nederlandse voor Metra Axxess XSVI-1731-NAV (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 13 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Installation instructions for part XSVI-1731-NAV

REV. 9/29/2016 INSTXSVI-1731-NAV

Axxess Integrate

CAUTION!

All accessories, switches, climate controls panels, and

especially air bag indicator lights must be connected before cycling

the ignition. Also, do not remove the factory radio with the key in the

on position, or while the vehicle is running.

• Provides NAV outputs (parking brake, reverse, and speed sense)

• Pre-wired ASWC-1 harness included (ASWC-1 sold separately)

• Retains the factory backup camera

• Retains balance and fade

• Includes the AX-CAM6V 12-volt to 6-volt converter

• Micro “B” USB updatable

FEATURES

• Wire cutter • Crimp tool • Solder gun • Tape

• Connectors (example: butt-connectors, bell caps, etc.)

TOOLS REQUIRED

XSVI-1731-NAV

Honda Data Interface 2016-up

APPLICATIONS

• XSVI-1731-NAV interface • XSVI-1731-NAV harness • AX-CAM6V 12-volt to 6-volt converter

INTERFACE COMPONENTS

HONDA

Civic LX 2016-up

Connections to be made ................................................... 2

Installing the XSVI-1731-NAV .......................................... 3

Initializing the XSVI-1731-NAV ........................................ 3

TABLE OF CONTENTS

XSVI-1731-NAV

Connections to be made

From the XSVI-1731-NAV harness to the aftermarket radio:

•

Connect the wire to chassis ground, and also to the Black wire of the AX-CAM6V.Black

• Connect the Yellow wire to the battery wire.

• Connect the Red wire to the accessory wire.

• If the vehicle is equipped with a factory backup camera:

• Connect the Red wire labeled “6-volt camera” to the AX-CAM6V (sold separately).

• Connect the Yellow RCA jack to the backup camera input.

• If the aftermarket radio has an illumination wire, connect the wire to it.Orange

• Connect the Gray wire to the right front positive speaker output.

• Connect the Gray/Black wire to the right front negative speaker output.

• Connect the White wire to the left front positive speaker output.

• Connect the White/Black wire to the left front negative speaker output.

• Connect the Green wire to the left rear positive speaker output.

• Connect the Green/Black wire to the left rear negative speaker output.

• Connect the Purple wire to the right rear positive speaker output.

• Connect the Purple/Black wire to the right rear negative speaker output.

The following (3) wires are only for multimedia/navigation radios that require

these wires.

• Connect the Blue/Pink wire to the VSS/speed sense wire.

• Connect the Green/Purple wire to the reverse wire.

Note: Before connecting this wire, also refer to the “AX-CAM6V 12-volt to 6-volt”

converter section.

• Connect the Light Green wire to the parking brake wire.

AX-CAM6V 12-volt to 6-volt converter:

• Connect the Blue/Red Red wire to the wire labeled “Camera Power 6V”.

• Connect the Blue/White Green/Purple wire to the wire.

Note: The wire will connect to both the AX-CAM6V, Green/Purple

and the aftermarket radio.

12-pin pre-wired ASWC-1 harness:

• This harness is to be used along with the optional ASWC-1 (not included) to

retain steering wheel audio controls. If the ASWC-1 is not being used, disregard

this harness. If it will be used, please refer to the ASWC-1 instructions for radio

connections and programming.

Note: Disregard the harness that comes with the ASWC-1.

• Connect the Red wire to the accessory wire.

XSVI-1731-NAV

Installing the XSVI-1731-NAV

With the key in the off position:

• Connect the XSVI-1731-NAV harness into the interface, and then to the harness in

the vehicle.

Attention! If the interface loses power for any reason, the following steps will need to be

performed again. Also, if installing an ASWC-1 connect it after you initialize and test the

interface/radio, with the key in the off position.

• Turn the key (or push-to-start button) to the ignition position and wait until the radio

comes on.

Note: If the radio does not come on within 60 seconds, turn the key to the off

position, disconnect the interface, check all connections, reconnect the interface,

and then try again.

• Turn the key to the off position, and then to the accessory position. Test all functions

of the installation for proper operation, before reassembling the dash.

Initializing the XSVI-1731-NAV

Product specificaties

Merk:	Metra
Categorie:	Niet gecategoriseerd
Model:	Axxess XSVI-1731-NAV

Heb je hulp nodig?

Als je hulp nodig hebt met Metra Axxess XSVI-1731-NAV stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Metra

Metra 95-7022HG Handleiding

12 November 2024

Metra 95-7642 Handleiding

12 November 2024

Metra 71-017C Handleiding

26 September 2024

Metra AXSP-HK Handleiding

26 September 2024

Metra 109-TO7 Handleiding

24 September 2024

Metra 95-8273B Handleiding

6 September 2024

Metra 95-7822 Handleiding

6 September 2024

Metra 82-8703 Handleiding

6 September 2024

Metra 88-00-9004 Handleiding

6 September 2024

Metra 82-9101 Handleiding

6 September 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024

Kramer K-Bar Camera Bracket Handleiding

26 November 2024

Kramer RK-19 Handleiding

26 November 2024

Kramer OSP-MM1 Handleiding

26 November 2024

Kramer ASPEN-1616UX Handleiding

26 November 2024

Korg Pitchstrap Handleiding

26 November 2024

NeoMounts WL70-450BL11 Handleiding

26 November 2024

Kramer CLS-AOCH/60 Handleiding

26 November 2024

Klauke EKM 6022ISM Handleiding

26 November 2024