Metra AX-MC90082 Handleiding

Metra Niet gecategoriseerd AX-MC90082

Lees hieronder de 📖 handleiding in het Nederlandse voor Metra AX-MC90082 (5 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/5

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

AX-MC90082

I N S TA L L A T I O N I N S T R U C T I O N S

INTERFACE FEATURES

INTERFACE COMPONENTS

TOOLS REQUIRED

• Wire cutter • Crimp tool • Solder gun • Tape

• Connectors (example: butt-connectors, bell

caps, etc.)

TABLE OF CONTENTS

Connections ............................................................2

Installation .............................................................3

Programming .........................................................3

Mercedes ML (W164) (with M.O.S.T. 25 ampliﬁer)

Data Interface with SWC 2005-2011

Mercedes GL (X164) (with M.O.S.T. 25 ampliﬁer)

Data Interface with SWC 2006-2010

• Provides accessory power

• Retains R.A.P. (retained accessory power)

• Designed for ampliﬁed models

• Provides NAV outputs (parking brake, reverse, speed sense)

• Retains audio controls on the steering wheel

• Retains balance

• Micro-B USB updatable

• AX-MC90082 interface

• AX-MC90082 ampliﬁer interface

• ASWC-1 interface

• AX-MC90082 harness

• ASWC-1 harness

• Female 3.5mm connector with stripped leads

CONNECTIONS

From the aftermarket radio to the AX-MC90082 harness:

• Connect the wire to the ground wire.Black

• Connect the Yellow wire to the battery wire.

• Connect the wire to the accessory wire.Red

• If the aftermarket radio has an illumination wire, connect the wire to it.Orange

• Connect the wire to the amp turn on wire of the new radio. *Blue

* wire triggers the factory antenna booster as well as the ﬁber-optic box.Blue

• Connect the Brown wire to the mute wire.

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Connect the wire to the VSS/speed sense wire.Blue/Pink

• Connect the wire to the reverse wire.Green/Purple

• Connect the wire to the parking brake wire.Light Green

• Tape off and disregard the following (8) wires, they will not be used in this application:

Gray, Gray/Black Green Green/Black Purple Purple/Black White White/Black, , , , , ,

•

Connect the and RCA jacks to the front ampliﬁer output jacks of the aftermarket radio.Red White

From the aftermarket radio to the ASWC-1 harness:

This harness is only to be used if the vehicle is equipped with steering wheel controls.

• Connect the wire to the accessory wire.Red

• For the radios listed below, connect the

female 3.5mm connector with stripped leads

, to

the

male 3.5mm SWC jack from the ASWC-1 harness. Any remaining wires tape off and disregard

• Connect the steering wheel control wire, normally Eclipse: Brown Brown/, to the

White wire of the connector. Then connect the remaining steering wheel control wire,

normally , to the wire of the connector.Brown/White Brown

• Connect the steering wheel control Key 1 wire (Gray) to the Metra OE: Brown wire.

• Kenwood or select JVC with a steering wheel control wire: Connect the Blue/Yellow

wire to the wire.Brown

• XITE:

Connect the steering wheel control SWC-2 wire from the radio to the wireBrown

•

Parrot Asteroid Smart or Tablet: Connect the 3.5mm jack into the AX-SWC-PARROT (sold

separately), and then connect the 4-pin connector from the AX-SWC-PARROT into the radio

Note:

The radio must be updated to rev. 2.1.4 or higher software.

•

Universal “2 or 3 wire” radio:

Connect the steering wheel control wire, referred to as

Key-A or SWC-1, to the

Brown

wire of the connector. Then connect the remaining

steering wheel control wire, referred to as Key-B or SWC-2, to the

Brown/White

wire of

the connector. If the radio comes with a third wire for ground, disregard this wire.

Note:

After the interface has been programmed to the vehicle, refer to the manual

provided with the radio for assigning the SWC buttons. Contact the radio manufacturer

for more information.

• For all other radios: Connect the 3.5mm jack from the ASWC-1 harness, into the jack on the

aftermarket radio designated for an external steering wheel control interface. Please refer to

the aftermarket radios manual if in doubt as to where the 3.5mm jack goes to.

REV. 4/28/2020 INSTAX-MC90082

With the key in the off position:

• Connect the AX-MC90082 harness to the AX-MC90082 interface.

• Connect the AX-MC90082 harness to the AX-MC90082 ampliﬁer interface.

• Remove the dust cover from ﬁber optic port in the AX-MC90082 ampliﬁer interface.

• Connect the factory ﬁber optic cable into the AX-MC90082 ampliﬁer interface.

• Connect the AX-MC90082 harness to the wiring harness in the vehicle.

• Connect the ASWC-1 harness to the ASWC-1 interface, and then to the AX-MC90082 interface.

INSTALLATION

• Press and hold the Volume-Up button on the steering wheel.

• Turn the ignition on, the L.E.D. in the ASWC-1 interface will start ﬂashing rapidly, which

means the ASWC-1 is looking for the vehicle and the radio.

Note:

If the L.E.D. did not start ﬂashing rapidly, press the reset button for 3 seconds, while

still holding the Volume-Up button.

•

After a few seconds the L.E.D. should stop ﬂashing rapidly, and then go out for approximately 2 seconds

• After approximately 2 seconds there will be a series of 7 ﬂashes, some short, and Green

some long. The long ﬂashes represent the wires that are connected to the ASWC-1. The 3rd,

4th, 5th, and 6th ﬂashes should be longer.

Tip:

Knowing this will help to troubleshoot, if need be.

• The L.E.D. will pause for another 2 seconds, and then ﬂash up to 18 times depending on Red

which radio is connected to the ASWC-1. Refer to the L.E.D. feedback section for information.

• This is the end of the auto detection stage. Release from holding the Volume-Up button.

If the ASWC-1 detected the vehicle and the radio successfully, the L.E.D. will light up solid.

• Test the steering wheel controls for proper operation. Refer to the ASWC-1 instructions online

at axxessinterfaces.com for customizing the buttons, if so desired.

PROGRAMMING

(CONT.)

L.E.D. feedback

The (18) L.E.D. ﬂashes represent what brand radio the ASWC-1 believes it is connected Red

to. Each ﬂash represents a different radio manufacturer. For example, if you are installing

a JVC radio, the

ASWC-1

will ﬂash (5) times. Following is a legend that dictates which

manufacturer corresponds to which ﬂash.

L.E.D. feedback legend

* Note:

If the ASWC-1 ﬂashes (7) times, and you do not have an Alpine radio connected Red

to it, that means the ASWC-1 does not detect a radio connected it. Verify that the 3.5mm

jack is connected to the correct steering wheel jack/wire in the radio.

** Note:

Part number AX-SWC-PARROT is required (sold separately). Also, the Parrot radio

must be updated to rev. 2.1.4 or higher through www.parrot.com.

† Note:

If you have a Clarion radio and the steering wheel controls do not work, change the radio

type to the other Clarion radio type; same for Eclipse. The following section explains how to do this

‡ Note:

If you have a Kenwood radio and the L.E.D. feedback comes back as showing as a JVC

radio, change the radio type to a Kenwood. The following section explains how to do this.

1 ﬂash - Eclipse (Type 1) †

2 ﬂashes - Kenwood ‡

3 ﬂashes - Clarion (Type 1) †

4 ﬂashes - Sony / Dual

5 ﬂashes - JVC

ﬂashes -

Pioneer / Jensen

7 ﬂashes - Alpine *

8 ﬂashes - Visteon

9 ﬂashes - Valor

10 ﬂashes - Clarion (Type 2) †

11 ﬂashes - Metra OE

12 ﬂashes - Eclipse (Type 2) †

13 ﬂashes - LG

14 ﬂashes - Parrot **

15 ﬂashes - XITE

16 ﬂashes - Philips

17 ﬂashes - TBD

18 ﬂashes - JBL

Product specificaties

Merk:	Metra
Categorie:	Niet gecategoriseerd
Model:	AX-MC90082

Heb je hulp nodig?

Als je hulp nodig hebt met Metra AX-MC90082 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Metra

Metra 95-7022HG Handleiding

12 November 2024

Metra 95-7642 Handleiding

12 November 2024

Metra 71-017C Handleiding

26 September 2024

Metra AXSP-HK Handleiding

26 September 2024

Metra 109-TO7 Handleiding

24 September 2024

Metra 95-8273B Handleiding

6 September 2024

Metra 95-7822 Handleiding

6 September 2024

Metra 82-8703 Handleiding

6 September 2024

Metra 88-00-9004 Handleiding

6 September 2024

Metra 82-9101 Handleiding

6 September 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024

Kramer K-Bar Camera Bracket Handleiding

26 November 2024

Kramer RK-19 Handleiding

26 November 2024

Kramer OSP-MM1 Handleiding

26 November 2024

Kramer ASPEN-1616UX Handleiding

26 November 2024

Korg Pitchstrap Handleiding

26 November 2024

NeoMounts WL70-450BL11 Handleiding

26 November 2024

Kramer CLS-AOCH/60 Handleiding

26 November 2024

Klauke EKM 6022ISM Handleiding

26 November 2024