Metra AX-BM90122 Handleiding

Metra Niet gecategoriseerd AX-BM90122

Lees hieronder de 📖 handleiding in het Nederlandse voor Metra AX-BM90122 (5 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/5

AX-BM90122

I N S TA L L A T I O N I N S T R U C T I O N S

Product Info

INTERFACE FEATURES

INTERFACE COMPONENTS

TOOLS & INSTALLATION ACCESSORIES REQUIRED

• Crimping tool and connectors, or solder gun,

solder, and heat shrink • Tape • Wire cutter

• Zip ties

TABLE OF CONTENTS

Connections ............................................................2

Installation ............................................................. 3

Programming ......................................................... 3

BMW (with M.O.S.T. 25 ampliﬁer) 2004-2013

• Provides accessory power (12 volt 10 amp)

• Retains R.A.P. (retained accessory power)

• Designed for ampliﬁed models

• Retains audio controls on the steering wheel

• Retains phone buttons (radio dependent)

• Retains factory features: date, time, temperature display

• Micro-B USB updatable

• AX-BM90122 interface

• AX-BM90122 ampliﬁer interface

• ASWC-1 interface

• AX-BM90122 harness

• ASWC-1 harness

• 3.5mm adapter

APPLICATIONS

BMW

1-Series 2004-2013 3-Series 2005-2012

CONNECTIONS

From the aftermarket radio to the AX-BM90122 harness, connect the:

• wire to the ground wire.Black

• Yellow wire to the battery wire.

• Yellow wire (6’ long w/ fuse-holder) directly to the vehicles battery.

• wire to the accessory wire.Red

• Orange wire to the illumination wire (if applicable).

• wire to the power antenna turn-on wire.Blue

• Brown wire to the mute wire.

The following (3) wires are only for multimedia/navigation radios that require these wires.

• wire to the VSS/speed sense wire.Blue/Pink

• Green/Purple wire to the reverse wire.

• Light Green wire to the parking brake wire.

•

Tape off and disregard the following (8) wires, they will not be used in this application:

Gray, Gray/Black Green Green/Black Purple Purple/Black White White/Black, , , , , ,

• and RCA jacks to the full range ampliﬁer output jacks.Red White

ASWC-1 harness:

This harness is only to be used if the vehicle is equipped with steering wheel controls.

• Connect the wire to the chassis ground.Black

• Connect the wire to accessory power.Red

• For the radios listed below: Connect the

3.5mm adapter

to the male 3.5mm SWC jack from the

ASWC-1 harness. Any remaining wires tape off and disregard:

• Connect the steering wheel control wire, normally Eclipse: Brown Brown/White, to the wire

of the connector. Then connect the remaining steering wheel control wire, normally Brown/

White Brown, to the wire of the connector.

• Connect the steering wheel control Key 1 wire to the Metra OE: (Gray) Brown wire.

• Kenwood or select JVC with a steering wheel control wire: Blue/Yellow Connect the wire to

the wire.Brown

• Connect the steering wheel control SWC-2 wire from the radio to the XITE: Brown wire.

• Parrot Asteroid Smart or Tablet: Connect the 3.5mm jack into the AX-SWC-PARROT (sold

separately), and then connect the 4-pin connector from the AX-SWC-PARROT into the radio.

Note:

The radio must be updated to rev. 2.1.4 or higher software.

• Universal “2 or 3 wire” radio: Connect the steering wheel control wire, referred to as Key-A or

SWC-1, to the Brown wire of the connector. Then connect the remaining steering wheel control

wire, referred to as Key-B or SWC-2, to the wire of the connector. If the radio Brown/White

comes with a third wire for ground, disregard this wire.

Note:

After the interface has been programmed to the vehicle, refer to the manual provided with

the radio for assigning the SWC buttons. Contact the radio manufacturer for more information.

• Connect the 3.5mm jack from the ASWC-1 harness, into the jack on the For all other radios:

aftermarket radio designated for an external steering wheel control interface. Please refer to the

aftermarket radios manual if in doubt as to where the 3.5mm jack goes to.

REV. 11/13/2019 INSTAX-BM90122

With the key in the off position:

• Connect the AX-BM90122 harness AX-BM90122 interface to the .

• Connect the AX-BM90122 harness AX-BM90122 ampliﬁer interface to the .

• Remove the dust cover from ﬁber optic port in the AX-BM90122 ampliﬁer interface.

• Connect the factory ﬁber optic cable into the AX-BM90122 ampliﬁer interface.

• Connect the AX-BM90122 harness to the wiring harness in the vehicle.

• Connect the ASWC-1 harness ASWC-1 interface to the , and then to the AX-BM90122 interface.

• Press and hold the Volume-Up button on the steering wheel.

• Turn the ignition on, the L.E.D. in the ASWC-1 interface will start ﬂashing rapidly, which

means the ASWC-1 is looking for the vehicle and the radio.

Note:

If the L.E.D. did not start ﬂashing rapidly, press the reset button for 3 seconds, while still

holding the Volume-Up button.

• After a few seconds the L.E.D. should stop ﬂashing rapidly, and then go out for

approximately 2 seconds.

• After approximately 2 seconds there will be a series of 7 ﬂashes, some short, and Green

some long. The long ﬂashes represent the wires that are connected to the ASWC-1. The 3rd,

4th, 5th, and 6th ﬂashes should be longer.

Tip:

Knowing this will help to troubleshoot, if need be.

• The L.E.D. will pause for another 2 seconds, and then ﬂash up to 18 times depending on Red

which radio is connected to the ASWC-1. Refer to the L.E.D. feedback section for information.

• This is the end of the auto detection stage. Release from holding the Volume-Up button.

If the ASWC-1 detected the vehicle and the radio successfully, the L.E.D. will light up solid.

•

Test the steering wheel controls for proper operation. Refer to the ASWC-1 instructions online at

axxessinterfaces.com for customizing the buttons, if so desired

INSTALLATION

PROGRAMMING

(CONT.)

L.E.D. feedback

The (18) L.E.D. ﬂashes represent which brand radio the ASWC-1 is connected to. Each Red

ﬂash represents a different radio manufacturer. For example, if you are installing a JVC radio,

the ASWC-1 will ﬂash (5) times, and then stop. Following is a legend that dictates which Red

radio manufacturer corresponds to which ﬂash.

L.E.D. feedback legend

1 ﬂash - Eclipse (Type 1) †

2 ﬂashes - Kenwood ‡

3 ﬂashes - Clarion (Type 1) †

4 ﬂashes - Sony / Dual

5 ﬂashes - JVC

ﬂashes -

Pioneer / Jensen

7 ﬂashes - Alpine *

8 ﬂashes - Visteon

9 ﬂashes - Valor

10 ﬂashes - Clarion (Type 2) †

11 ﬂashes - Metra OE

12 ﬂashes - Eclipse (Type 2) †

13 ﬂashes - LG

14 ﬂashes - Parrot **

15 ﬂashes - XITE

16 ﬂashes - Philips

17 ﬂashes - TBD

18 ﬂashes - JBL

* Note:

If the ASWC-1 ﬂashes (7) times, and you do not have an Alpine radio connected to Red

it, that means the ASWC-1 does not detect a radio connected it. Verify that the 3.5mm jack is

connected to the correct steering wheel jack/wire in the radio.

** Note:

The AX-SWC-PARROT is required (sold separately). Also, the Parrot radio must be

updated to rev. 2.1.4 or higher through www.parrot.com.

† Note:

If you have a Clarion radio and the steering wheel controls do not work, change the radio type to

the other Clarion radio type; same for Eclipse. Refer to the “Programming Information” document online

‡ Note:

If you have a Kenwood radio and the L.E.D. feedback comes back as showing as a JVC radio,

change the radio type to a Kenwood. Refer to the “Programming Information” document online

Product specificaties

Merk:	Metra
Categorie:	Niet gecategoriseerd
Model:	AX-BM90122

Heb je hulp nodig?

Als je hulp nodig hebt met Metra AX-BM90122 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Metra

Metra 95-7022HG Handleiding

12 November 2024

Metra 95-7642 Handleiding

12 November 2024

Metra 71-017C Handleiding

26 September 2024

Metra AXSP-HK Handleiding

26 September 2024

Metra 109-TO7 Handleiding

24 September 2024

Metra 95-8273B Handleiding

6 September 2024

Metra 95-7822 Handleiding

6 September 2024

Metra 82-8703 Handleiding

6 September 2024

Metra 88-00-9004 Handleiding

6 September 2024

Metra 82-9101 Handleiding

6 September 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Livarno Lux IAN 071407 Handleiding

29 November 2024

Livarno Lux IAN 317128 Handleiding

29 November 2024

Livarno Lux IAN 049213 Handleiding

29 November 2024

Livarno Lux ST-1002 Handleiding

29 November 2024

Livarno Lux HG02489 Handleiding

29 November 2024

Livarno Lux HG02189 Handleiding

29 November 2024

Livarno Lux IAN 365198 Handleiding

29 November 2024

Livarno Lux IAN 367074 Handleiding

29 November 2024

Livarno Lux HG00701 Handleiding

29 November 2024

Livarno Lux IAN 337273 Handleiding

29 November 2024