Metra 99-9229G Handleiding

Metra Niet gecategoriseerd 99-9229G

Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 99-9229G (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

REV. 9/10/2015 INST99-9229G

Installation instructions for part 99-9229G

CAUTION!

Metra recommends disconnecting the negative bat

tery terminal before beginning any installation, unless the vehicle

manufacturer recommends against so. Please check with your local

Dealership for more information. All accessories, switches, climate

controls panels, and especially air bag indicator lights must be con-

nected before reconnecting the battery or cycling the ignition. Also,

do not remove the factory radio with the key in the on position, or the

vehicle running. It would be best to remove the key from the ignition

and then wait a few seconds before removing the factory radio.

• ISO DIN radio provision with pocket

• ISO DDIN radio provision

• Painted to match factory finish

• A) Radio trim panel • B) Radio housing • C) Pocket • D) (4) #8 x 3/8” Phillips screws • E) (4) Panel clips

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • 70-9221

Antenna Adapter: • 40-VL10

• Panel removal tool • Phillips screwdriver • T-25 Torx driver

TOOLS REQUIRED

Volvo S60/V70 2001-2004

99-9229G

A B C

Dash Disassembly ................................................. 2

Kit Assembly

– ISO DIN radio provision with pocket ...................... 3

–ISO DDIN radio provision ...................................... 3

Table of Contents

D E

99-9229G

1. Remove the panel between the

climate control and gear selector.

(Figure A)

2. Move the gear selector as far back

as possible, unsnap the panel

surrounding it, and then rotate it

45 degrees either way. (Figure B)

3. Remove (2) T-25 screws now

exposed securing the climate

control panel to the vehicle, and

then remove. (Figure C)

Continue to 3 a.

Dash Disassembly

a. Angle the panel outwards so

that it is possible to insert a

couple of fingers between the

center console and the side of

the panel. (Figure D)

b. Remove the panel by pulling

it downward, maintaining the

same angle. Some force is

required because the panel is

tightly installed. (Figure D)

c. Do not unplug the connectors.

Place the panel to one side instead

4. Remove (2) T-25 Torx screws

securing the radio, and then

remove. (Figure E)

5. Remove the sub-dash bracket from

the radio, and then remove.

a. Remove (5) T-25 Torx screws

securing the bracket. (Figure F)

b. Depress the snaps on the top

and bottom of the pocket.

(Figure G)

Continue to kit assembly

(Figure B) (Figure E)

(Figure A)

(Figure C) (Figure F)

(Figure D) (Figure G)

99-9229G

Kit Assembly

ISO DIN radio provision with pocket

1. Secure the pocket radio to the

housing using (4) #8 x 3/8” Phillips

screws provided. (Figure A)

Note: Rounded edge of pocket

faces towards the bottom.

2. Remove the metal DIN sleeve and

trim ring from the aftermarket radio.

3. Slide the radio into the completed

assembly, and then secure it to the

assembly using screws supplied

with the radio. (Figure A)

Locate the factory wiring harness and

antenna connector in the dash, and

complete all necessary connections to the

radio. Metra recommends using the proper

mating adapter from Metra and/or AXXESS.

Re-connect the negative battery terminal

and test the radio for proper operation.

5. Reassemble the dash in reverse

order of disassembly.

6. Attach (4) panel clips supplied to

the , and then snap radio trim panel

the panel over the radio.

ISO Double DIN radio provision

1. Slide the radio into the radio

housing and secure it using screws

supplied with the radio.

(Figure A)

2. Locate the factory wiring harness

and antenna connector in the

dash, and complete all necessary

connections to the radio. Metra

recommends using the proper

mating adapter from Metra and/or

AXXESS. Re-connect the negative

battery terminal and test the radio

for proper operation.

3. Reassemble the dash in reverse

order of disassembly.

4. Attach (4) panel clips supplied to

the , and then snap radio trim panel

the panel over the radio.

(Figure A) (Figure A)

Product specificaties

Merk:	Metra
Categorie:	Niet gecategoriseerd
Model:	99-9229G

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 99-9229G stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Metra

Metra 95-7022HG Handleiding

12 November 2024

Metra 95-7642 Handleiding

12 November 2024

Metra 71-017C Handleiding

26 September 2024

Metra AXSP-HK Handleiding

26 September 2024

Metra 109-TO7 Handleiding

24 September 2024

Metra 95-8273B Handleiding

6 September 2024

Metra 95-7822 Handleiding

6 September 2024

Metra 82-8703 Handleiding

6 September 2024

Metra 88-00-9004 Handleiding

6 September 2024

Metra 82-9101 Handleiding

6 September 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024

Kramer K-Bar Camera Bracket Handleiding

26 November 2024

Kramer RK-19 Handleiding

26 November 2024

Kramer OSP-MM1 Handleiding

26 November 2024

Kramer ASPEN-1616UX Handleiding

26 November 2024

Korg Pitchstrap Handleiding

26 November 2024

NeoMounts WL70-450BL11 Handleiding

26 November 2024

Kramer CLS-AOCH/60 Handleiding

26 November 2024

Klauke EKM 6022ISM Handleiding

26 November 2024