Metra 99-7638 Handleiding

Metra Carkit 99-7638

Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 99-7638 (5 pagina's) in de categorie Carkit. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/5
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 9/28/20 INST99-7638
I N S TA L L AT I O N I N S T R U C T I O N S
99-7638
Attention! Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
KIT COMPONENTS
• A) Radio housing (front) • B) Radio housing (rear) • C) Radio trim panel • D) Radio brackets • E) #4 x 3/8” Phillips screws (4)
• F) #6 x 3/8” Phillips screws (4) • G) Panel clips (3)
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 10mm socket wrench
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS
(sold separately)
Wiring Harness: 70-7552
Antenna Adapter: 40-NI12
A B C E F
D
Nissan Sentra 2020-Up
G
Visit for more detailed information about the product and up-to-date vehicle MetraOnline.com
specific applications
KIT FEATURES
ISO DIN radio provision with pocket
Painted with a gloss black face, silver trim, and a textured housing.
2386.257.1187
|
MetraOnline.com
1. Unclip and remove the trim panel
behind the radio. There are (4) clips
securing this panel to the dash. Use
caution as the front of the trim panel
can easily be damaged. (Figure A)
Dash vents may vary depending Note:
on Nissan model.
2. Remove (4) 10mm screws securing the
radio. Take note that the lower radio
brackets are angled inward, hiding the
bottom (2) screws from being easily
seen. Slide the radio out, then unplug
and remove the radio. (Figure B)
Continue to Kit Assembly
(Figure A) (Figure B)
DASH DISASSEMBLY
REV. 9/28/2020 INST99-7638 3
KIT ASSEMBLY
1. Attach (3) provided onto the panel clips
radio housing (front). (Figure A)
2. Snap the radio housing (front) to the
radio housing (rear), then secure using
(4) #4 x 3/8” Phillips screws provided
(Figure B)
3. radio brackets Secure the to the radio
housing using (4) #6 x 3/8” Phillips
screws provided. (Figure C)
4. Clip the onto the radio radio trim panel
housing assembly. (Figure D)
5. Remove the metal DIN sleeve and trim
ring from the aftermarket radio.
6. Slide the radio into the radio housing
assembly through the back, then secure
it to the assembly using screws supplied
with the radio. (Figure E)
7. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using
the proper mating adapter from Metra
and/or Axxess. Test the radio for proper
operation.
8. Secure the radio assembly to the dash
using the factory screws.
9. Snap the factory trim panel to the dash
to complete the installation.
(Figure A) (Figure D)
(Figure B) (Figure E)
(Figure C)


Product specificaties

Merk: Metra
Categorie: Carkit
Model: 99-7638

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 99-7638 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Carkit Metra

Metra

Metra 99-7339B Handleiding

17 November 2024
Metra

Metra 99-7345B Handleiding

17 November 2024
Metra

Metra AX-ADCT4 Handleiding

17 November 2024
Metra

Metra 95-7883HG Handleiding

17 November 2024
Metra

Metra 95-5026 Handleiding

17 November 2024
Metra

Metra 99-7367HG Handleiding

23 Augustus 2024
Metra

Metra 99-8223 Handleiding

23 Augustus 2024
Metra

Metra 99-7422 Handleiding

23 Augustus 2024
Metra

Metra 99-7875 Handleiding

23 Augustus 2024

Handleiding Carkit

Nieuwste handleidingen voor Carkit