Metra 99-7411 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 99-7411 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
99-7411
INSTALLATION
INSTRUCTIONS
APPLICATIONS
CAR PAGE
NISSAN
300ZX 1984-87.......................................................1-2
KIT COMPONENTS
TOOLS REQUIRED
Cutting tool
Wrench
Phillips screwdriver
(4) Phillips Pan-head
Screws
(4) Speed Clips
KIT FEATURES
Shaft and
DIN unit
provisions
e
Radio Housing
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2001 METRA ELECTRONICS CORPORATION
rev. 250701
1 2
3 4
Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adaptor and making
connections as shown. (Isolate and
individually tape off the ends of any
unused wires to prevent electrical short
circuit).
Re-connect the battery terminal and test the unit
for proper operation. Mount the factory radio
housing to the sub-dash with (4) Phillips screws
previously removed in step #1.
A
B
C
D
A) Strip wire ends back ½"
B) Twist ends together
C) Solder
D) Tape
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the
ashtray and (2) screws exposed. Remove (2) screws above the climate controls. Unclip the
radio trim bezel and remove. Remove (4) Phillips screws securing the factory radio housing,
pull the housing assembly out and disconnect the wiring. Remove the screws securing the
factory radio to the factory radio housing and remove.
1
2-SHAFT HEAD UNITS: Snap the Faceplate onto the the front of the Radio Housing. Mount
the Faceplate/Radio Housing assembly to the factory radio housing with (4) Phillips Pan-
head Screws (4) Speed Clips and supplied. Slide the aftermarket head unit into the kit and
secure with shaft nuts.
DIN HEAD UNITS: Cut and remove the shaft supports from the Faceplate. Snap the
Faceplate onto the front of the Mount the Faceplate/Radio Housing Radio Housing.
assembly to the factory radio housing with (4) Phillips Pan-head Screws and (4) Speed Clips
supplied. Slide the DIN cage into the Housing and secure by bending the metal locking tabs
down. Slide the aftermarket head unit into the cage until secure.
2a
2b
ALL VEHICLES
Factory radio
housing
Radio trim bezel


Product specificaties

Merk: Metra
Categorie: Niet gecategoriseerd
Model: 99-7411

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 99-7411 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Metra

Metra

Metra 95-7022HG Handleiding

12 November 2024
Metra

Metra 95-7642 Handleiding

12 November 2024
Metra

Metra 71-017C Handleiding

26 September 2024
Metra

Metra AXSP-HK Handleiding

26 September 2024
Metra

Metra 109-TO7 Handleiding

24 September 2024
Metra

Metra 95-8273B Handleiding

6 September 2024
Metra

Metra 95-7822 Handleiding

6 September 2024
Metra

Metra 82-8703 Handleiding

6 September 2024
Metra

Metra 88-00-9004 Handleiding

6 September 2024
Metra

Metra 82-9101 Handleiding

6 September 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd