Metra 99-7394B Handleiding

Metra Niet gecategoriseerd 99-7394B

Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 99-7394B (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

Metra. The World’s Best Kits.

I N S TA L L AT I O N I N S T R U C T I O N S

99-7394B

Attention! Let the vehicle sit with the key

out of the ignition for a few minutes before

removing the factory radio. When testing the

aftermarket equipment, ensure that all factory

equipment is connected before cycling the

key to ignition.

KIT FEATURES

• ISO DIN radio provision

• ISO DDIN radio provision †

• Pioneer modular DDIN radio provision †

• Painted matte black

KIT COMPONENTS

• A) Radio housing (front) • B) Radio housing (rear) • C) Radio brackets • D) Pioneer adapter brackets • E) Blank panel

• F) #4 x 3/8” Phillips screws (5) • G) #8 x 1/2” Phillips screws (4) • H) Panel clips (3) • I) Panel clips (4) TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

TABLE OF CONTENTS

Dash Disassembly ................................................... 2

Kit Assembly

- ISO DIN radio provision .........................................3

- ISO DIN radio provision ........................................4

- Pioneer modular DDIN radio provision .............. 5

WIRING & ANTENNA CONNECTION

(sold separately)

Wire harness: • 70-7306

Antenna adapter: • 40-KI11

Steering wheel control interface: • ASWC-1

12v-to-6v camera step-down: • AX-CAM6V

A B C D E

F H IG

Kia Forte 2019-up

Visit for more detailed information about the product and up-to-date vehicle MetraOnline.com

speciﬁc applications

† This kit can only be used with an ISO DDIN radio with an “L” shaped chassis design,

with the radio chassis at the bottom of the screen. As of this writing, only the Alpine

INE-W967HD (discontinued, replaced by INE-W977HD), iLX-107, and iLX-207 have this

design. Also, The Pioneer modular radios, DMH-C2550NEX and DMH-C2500NEX, can be

used with the included adapter brackets

1.800.221.0932

MetraOnline.com

DASH DISASSEMBLY

1. Unclip the instrument panel trim and

move aside just enough to clear the

silver panel below the radio. (Figure A)

2. Starting from the left, unclip and remove

the silver trim panel below the radio.

(Figure B)

3. Unclip, unplug, and remove the center

a/c vent and hazard assembly. (Figure C)

4. Unclip and remove the trim panel

behind the radio by pulling straight up.

There are (5) clips securing this panel to

the dash. (Figure D)

5. Remove (4) Phillips screws securing

the radio, two up top, and two down

below. Unclip and slide the radio out,

then unplug and remove the radio.

Remove the (4) panel clips for reuse in

Kit Assembly. (Figures E and F)

Continue to Kit Assembly

(Figure A) (Figure D)

(Figure B) (Figure E)

(Figure C) (Figure F)

REV. 6/28/2019 INST99-7394B 3

ISO DIN radio provision

1. Secure the to the blank panel radio

housing (front) using (2) #4 x 3/8”

Phillips screws provided. (Figure A)

2. Attach (3) provided onto the panel clips

radio housing (front). (Figure B)

3. radio housing (front) Snap the to the

radio housing (rear), then secure using

(3) #4 x 3/8” Phillips screws provided

(Figure C)

4. Secure the radio brackets to the radio

housing assembly using (4) #8 x 1/2”

Phillips screws provided. (Figure D)

5. Attach the (4) factory panel clips to the

radio housing assembly.

Note: (4) have been Panel clips

provided only if the factory clips are

missing or damaged.

KIT ASSEMBLY

6. Remove the metal DIN sleeve and trim

ring from the aftermarket radio.

7. Slide the radio into the radio housing

assembly through the back, then secure

using screws supplied with the radio.

(Figure E)

8. Locate the factory wiring harness and

antenna connector in the dash and

complete all necessary connections to

the radio. Metra recommends using

the proper mating adapter from Metra

and/or Axxess. Test the radio for proper

operation.

9. Secure the radio assembly to the dash

using the factory screws.

10. Reassemble the dash in reverse

order of disassembly to complete the

installation.

(Figure A) (Figure D)

(Figure B) (Figure E)

(Figure C)

Product specificaties

Merk:	Metra
Categorie:	Niet gecategoriseerd
Model:	99-7394B

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 99-7394B stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Metra

Metra 95-7022HG Handleiding

12 November 2024

Metra 95-7642 Handleiding

12 November 2024

Metra 71-017C Handleiding

26 September 2024

Metra AXSP-HK Handleiding

26 September 2024

Metra 109-TO7 Handleiding

24 September 2024

Metra 95-8273B Handleiding

6 September 2024

Metra 95-7822 Handleiding

6 September 2024

Metra 82-8703 Handleiding

6 September 2024

Metra 88-00-9004 Handleiding

6 September 2024

Metra 82-9101 Handleiding

6 September 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024

Kramer K-Bar Camera Bracket Handleiding

26 November 2024

Kramer RK-19 Handleiding

26 November 2024

Kramer OSP-MM1 Handleiding

26 November 2024

Kramer ASPEN-1616UX Handleiding

26 November 2024

Korg Pitchstrap Handleiding

26 November 2024

NeoMounts WL70-450BL11 Handleiding

26 November 2024

Kramer CLS-AOCH/60 Handleiding

26 November 2024

Klauke EKM 6022ISM Handleiding

26 November 2024