Metra 95-7377B Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 95-7377B (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
REV. 1/24/2017 INST95-7377B
INSTALLATION INSTRUCTIONS FOR PART 95-7377B
METRA – The World’s best kits.®metraonline.com © COPYRIGHT 2016 METRA ELECTRONICS CORPORATION
CAUTION!
All accessories, switches, climate controls panels,
and especially air bag indicator lights must be connected before
cycling the ignition. Also, do not remove the factory radio with
the key in the on position, or while the vehicle is running.
ISO DDIN radio provision
Painted matte black
A) Radio trim panel • B) Radio brackets C) (2) Panel clips
20;-,(;<9,:
20;*64765,5;:
>0905.(5;,55(*655,*;065: (sold separately)
Wiring Harness: • 70-7304 Antenna Adapter: Not required
Panel removal tool • Phillips screwdriver
;663:9,8<09,+
Kia Optima 2016-up
95-7377B
Table of Contents
A B C
Dash Disassembly ................................................. 2
Kit Preparation ....................................................... 3
Kit Assembly .......................................................... 3
95-7377B
2
Dash Disassembly
1. Open the glove box and remove the
trim at the top of the opening, and
then remove the (2) Phillips screws
exposed. (Figure A)
2. Unclip the trim that runs along the
dash from the right side A/C vent
to the steering column, and then
remove the (2) Phillips screws
securing the A/C vent/hazard panel.
(Figure B)
3. Unclip and remove the right side
trim panel from the center console,
and then remove the (1) Phillips
screw securing the A/C vent/hazard
panel. (Figure C)
4. Unclip the A/C vent/hazard panel,
disconnect the hazard switch, and
then remove the panel. (Figure D)
5. Using caution not to break the
panel, carefully unclip and remove
the radio trim panel. (Figure D)
(Figure B)
(Figure D)
(Figure E)
(Figure A) (Figure C)
Note: There are (8) clips that attach
the panel to the vehicle: (2) at
the top-middle, (2) at the bottom
corners, (2) at the top corners, and
(2) in the center (these 2 are only in
non-nav models). (Figure E)
6. Remove the (4) Philips screws
securing the radio and then remove.
Continue to Kit Preparation
95-7377B
3
(Figure A)(Figure A)
Kit AssemblyKit Preparation
ISO DDIN radio provision
1. Attach the radio brackets to the
radio using the screws supplied
with the radio. (Figure A)
2. Locate the factory wiring harness
and connector in the dash and
complete all necessary connections
to the radio. Metra recommends
using the proper mating adapter
from Metra and/or Axxess. Test the
radio for proper operation.
3. Secure the completed assembly into
the dash using the factory screws.
4. Snap the radio trim panel over the
completed assembly, and then
reassemble the dash in reverse
order of disassembly.
1. Attach the (2) to thepanel clips
radio trim panel as shown.
(Figure A)
Continue to Kit Assembly


Product specificaties

Merk: Metra
Categorie: Niet gecategoriseerd
Model: 95-7377B

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 95-7377B stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Metra

Metra

Metra 95-7022HG Handleiding

12 November 2024
Metra

Metra 95-7642 Handleiding

12 November 2024
Metra

Metra 71-017C Handleiding

26 September 2024
Metra

Metra AXSP-HK Handleiding

26 September 2024
Metra

Metra 109-TO7 Handleiding

24 September 2024
Metra

Metra 95-8273B Handleiding

6 September 2024
Metra

Metra 95-7822 Handleiding

6 September 2024
Metra

Metra 82-8703 Handleiding

6 September 2024
Metra

Metra 88-00-9004 Handleiding

6 September 2024
Metra

Metra 82-9101 Handleiding

6 September 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd