Metra 95-6554B Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 95-6554B (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 227 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 11/12/19 INST95-6554B
I N S TA L L AT I O N I N S T R U C T I O N S
95-6554B
Attention! Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
KIT FEATURES
ISO DDIN radio provision
Complete panel for a factory look and feel
Painted scratch resistant matte black
KIT COMPONENTS
A) Radio dash panel • B) Radio brackets • C) Phillips screw • D) Tape (not shown)
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• Cutting tool • 1/8” drill bit • 3/8” socket set
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation ...................................................3-4
Kit Assembly ..........................................................5
WIRING & ANTENNA CONNECTIONS
(sold separately)
Wiring Harness: 70-1817
Antenna Adapter: Not required
A B C
Jeep Cherokee 1997-2001
Visit for more detailed information about the product and up-to-date vehicle MetraOnline.com
specific applications
1.800.221.0932
|
MetraOnline.com
2
1. Unclip and remove the radio trim panel.
Remove the factory panel clips and A/C
vents for re-use in Kit Assembly.
(Figure A)
2. Remove (2) 3/8” screws securing the
radio. Slide the radio out, then unplug
and remove.
Continue to Kit Preparation
(Figure A)
DASH DISASSEMBLY
REV. 11/12/2019 INST95-6554B 3
KIT PREPARATION
Attention! The sub-dash of the vehicle
will have to be cut to allow room for the
aftermarket radio. Once cut, the factory radio
will no longer be able to be re-installed. Also
take note that the radio sub-dash is actually
the a/c vents for the vehicle. After the
sub-dash has been cut, the tape provided
will have to be used to cover up the holes to
prohibit air from leaking out.
For select Sony radios* with an “L” shaped
chassis design:
1. Remove (4) Phillips screws securing
the climate controls. Partially slide the
controls out and move down slightly.
2. Cut the sub-dash to allow room for the
aftermarket radio. (Figure B)
3. Apply tape over the area cut. (Figure C)
4. Cut the radio brackets as shown.
(Figure D)
5. Secure the climate controls back to the
vehicle using just the (2) lower screws.
The upper screws will be reused in
Kit Assembly.
* At present (9-12-19), models XAV-AX100,
XAV-AX1000, XAV-AX200, XAV-A500, and
XAV-V10BT have this design
Continue to Kit Assembly
(Figure A) (Figure C)
(Figure D)
Remove shaded area
Remove shaded area
Tape over the cut area
(Figure B)


Product specificaties

Merk: Metra
Categorie: Niet gecategoriseerd
Model: 95-6554B

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 95-6554B stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Metra

Metra

Metra 95-7022HG Handleiding

12 November 2024
Metra

Metra 95-7642 Handleiding

12 November 2024
Metra

Metra 71-017C Handleiding

26 September 2024
Metra

Metra AXSP-HK Handleiding

26 September 2024
Metra

Metra 109-TO7 Handleiding

24 September 2024
Metra

Metra 95-8273B Handleiding

6 September 2024
Metra

Metra 95-7822 Handleiding

6 September 2024
Metra

Metra 82-8703 Handleiding

6 September 2024
Metra

Metra 88-00-9004 Handleiding

6 September 2024
Metra

Metra 82-9101 Handleiding

6 September 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd