Metra 95-6549 Handleiding

Metra Carkit 95-6549

Lees hieronder de πŸ“– handleiding in het Nederlandse voor Metra 95-6549 (4 pagina's) in de categorie Carkit. Deze handleiding was nuttig voor 19 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
Metra. The World’s Best Kits.ξšŽξ˜ƒMetraOnline.com Β© COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 7/26/18 INST95-6549
I N S TA L L A T I O N I N S T R U C T I O N S
95-6549
KIT FEATURES
β€’ ISO DDIN radio provision
β€’ Complete center dash panel for a factory look
KIT COMPONENTS
β€’ A) Radio/climate control panel β€’ B) Radio brackets β€’ C) Tray β€’ D) Storage pocket β€’ E) Dummy panel β€’ F) Climate control spacers
β€’ G) (6) #8 x 3/8” Pan-head Phillips screws β€’ H) (4) #8 x 5/8” Pan-head Phillips screws β€’ I) (3) #8 x 1/2” Truss-head Phillips screws
TOOLS REQUIRED
β€’ Panel removal tool β€’ Phillips screwdriver
β€’ 3/8’ socket wrench β€’ Cutting tool β€’ Grinding tool
β€’ 1/8” drill bit
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation ....................................................2-3
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS
(sold separately)
Wiring Harness: 70-1817
Antenna Adapter: N/R
A B C
F HG I
D E
Jeep Wrangler 1997-2002
1.800.221.0932
|
MetraOnline.com
2
1. Unclip the top cover from the instrument
panel, then remove (2) Phillips screws
exposed.
2. Remove the ashtray, then remove (1)
Phillips screw exposed.
3. Starting from the bottom edge of the
radio/climate control panel, unclip,
unplug, and remove the panel.
4.
Remove (2) 3/8” screws securing the
radio to the dash. Slide the radio out,
then unplug and remove the radio.
Continue to Kit Preparation
(Figure A)
1. Remove (4) Phillips screws securing the
climate control panel to the dash, then
temporarily move it out of the way in
preparation for the next step.
2. Cut the shaded area in the sub-dash
to allow room for the radio assembly.
(Figure A)
Some radios may require more Note:
cutting than shown. Cut as needed to
allow room for the aftermarket radio.
The dash cut goes through the Note:
center of the lower left mounting hole.
(See detail)
From the factory radio/climate control panel:
3. Unclip and remove the a/c vents.
(Figure B)
4. Unclip and remove the cigarette lighter/
switch panel.
5. Remove the (2) panel clips.
Continued on the next page
DASH DISASSEMBLY KIT PREPARATION
(Figure A)
Remove shaded area
Detail
(Figure B)
REV. 7/26/2018 INST95-6549 3
To the 95-6549 radio/climate control panel:
7. Clip in the a/c vents.
8. Clip in the cigarette lighter/switch panel.
9. Attach the (2) panel clips.
10.
Clip in either the
storage pocket
or
dummy
panel
to replace the factory ashtray
.
11. Secure the
tray
to the
radio climate/control
panel
using the (2) #8 x 3/8” Phillips
pan-head screws provided. (Figure C)
12. Grind down the climate control panel
locater pins. (Figure D)
13. 1997-1999: Place the
climate control
spacers
onto the back of the climate
control panel, then secure the climate
control panel back to the vehicle using
the (4) #8 x 5/8” pan-head screws screws
provided. (Figure E)
2000-2002: Secure the climate control
panel to the
6549 panel
using the (4)
#8 x 3/8” Phillips pan-head screws
provided.
Continue to Kit Assembly
KIT PREPARATION (CONT.) KIT ASSEMBLY
1. Secure the
radio brackets
to the radio
using the screws supplied with the
radio. (Figure A)
2.
Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to the
radio. Metra recommends using the proper
mating adapter from Metra and/or Axxess.
Test the radio for proper operation
.
3. Secure the radio assembly to the dash
using (1) factory screw in the top right.
Drill an 1/8” hole in the (3) remaining
screw holes in the brackets, then use the
(3) #8 x 1/2” Phillips truss-head screws
provided to fully secure the radio.
4.
Reassemble the dash in reverse order of
disassembly to complete the installation
.
(Figure A)
(Figure C)
(Figure E)
(Figure D)


Product specificaties

Merk: Metra
Categorie: Carkit
Model: 95-6549

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 95-6549 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Carkit Metra

Metra

Metra 99-7339B Handleiding

17 November 2024
Metra

Metra 99-7345B Handleiding

17 November 2024
Metra

Metra AX-ADCT4 Handleiding

17 November 2024
Metra

Metra 95-7883HG Handleiding

17 November 2024
Metra

Metra 95-5026 Handleiding

17 November 2024
Metra

Metra 99-7367HG Handleiding

23 Augustus 2024
Metra

Metra 99-8223 Handleiding

23 Augustus 2024
Metra

Metra 99-7422 Handleiding

23 Augustus 2024
Metra

Metra 99-7875 Handleiding

23 Augustus 2024

Handleiding Carkit

Nieuwste handleidingen voor Carkit