Metra 91-3037P Handleiding


Lees hieronder de ๐Ÿ“– handleiding in het Nederlandse voor Metra 91-3037P (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3
IMPORTANT
Installation Kit
120 91-3037P
Before starting, compare items on your invoice with items
received. Carefully check through packaging material.
If an item is missing, please call:
Crutchfield
Parts Supplied:
Kit Frame
Support Tray
Chevrolet/GMC
Revision 12/10/03
Kit assembly instructions are on the following pages.
Page 1 of 3
ยฎ
Copyright 2003 Crutchfield Corporation
*120913037P*
Mounting Brackets
(2) Studs (2) 3/8โ€ Nuts
(4) 1/4โ€ Hex Screws
Trimplate
at 1-888-955-6000
FIGURE 2
Shaft Supports
Installation Kit
120 91-3037P
1. Press posts on trimplate into holes on kit frame to snap
parts together and secure with hex screws (Figure 1).
2. Use a utility knife to cut out in trimplate to shaft supports
create a DIN opening (Figure 2).
3. Push clips on into slots on rear of kit frame to support tray
secure (Figure 1).
4. Cut off tabs on both mounting brackets labeled โ€œBโ€ and โ€œCโ€
that are shown as shaded (Figure 3). The โ€œAโ€ tabs must
remain.
5. Secure mounting brackets to sides of kit frame with studs
and nuts supplied (Figure 1).
6. Remove DIN sleeve from receiver and slide into opening in
trimplate. Secure sleeve to trimplate by bending the securing
tabs (Figure 4).
7. Slide receiver into sleeve/kit assembly.
DIN Receiver Assembly
2
ยฎ
Copyright 2003 Crutchfield Corporation
Securing Tabs
DIN Sleeve
Bend tabs after sleeve
is inside assembly.
FIGURE 1
Trimplate
Kit Frame Support Tray
Left Mounting Bracket
Stud
Nut
Right Mounting Bracket
FIGURE 4
Hex Screws
Tools Required
Utility
Knife
โ–ฒ
Small Flat Blade
Screwdriver
1/4โ€ & 3/8โ€
Sockets
Hacksaw
Chevrolet/GMC
FIGURE 3
Cut off
โ€œBโ€ & โ€œCโ€ tabs
(shaded)
โ€œCโ€
โ€œBโ€
โ€œBโ€
โ€œAโ€ tabs remain
โ€œAโ€
โ€œAโ€
Installation Kit
120 91-3037P
Spacers
(supplied with
your order)
1. Press posts on trimplate into holes on kit frame to snap parts
together and secure with hex screws (Figure 1).
2. Push clips on into slots on rear of kit frame support tray
to secure (Figure 1).
3. Cut off tabs on both mounting brackets labeled โ€œBโ€ and โ€œCโ€
shown as shaded (Figure 2). The โ€œAโ€ tabs must remain.
4. Secure mounting brackets to sides of kit assembly with
studs nutsand supplied (Figure 1).
5. Choose the proper spacers (supplied with your order) to
allow receiver nosepiece to extend 1/8โ€ to 1/4โ€ beyond face of
trimplate (Figure 3).
6. Insert receiver shafts (with spacers in place) through openings
in trimplate. Secure receiver and faceplate with shaftnuts
supplied with receiver.
7. Attach control knobs.
1/8โ€ -1/4โ€
โ–ฒ
โ–ฒ
Spacer
Shaft Receiver Assembly
3
FIGURE 3
Shaftnuts
ยฎ
Copyright 2003 Crutchfield Corporation
FIGURE 1
Trimplate
Kit Frame
Support Tray
Left Mounting Bracket
Faceplate
Control Knobs
Tools Required
โ–ฒ
Deep Socket
(size depends upon receiver)
Stud
Nut
Right Mounting Bracket
1/4โ€ & 3/8โ€
Sockets
Hex Screws
FIGURE 2
Cut off
โ€œBโ€ & โ€œCโ€ tabs
(shaded)
Chevrolet/GMC
โ€œCโ€
โ€œBโ€
โ€œBโ€
โ€œAโ€ tabs must remain
โ€œAโ€
โ€œAโ€
Hacksaw


Product specificaties

Merk: Metra
Categorie: Niet gecategoriseerd
Model: 91-3037P

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 91-3037P stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Metra

Metra

Metra 95-7022HG Handleiding

12 November 2024
Metra

Metra 95-7642 Handleiding

12 November 2024
Metra

Metra 71-017C Handleiding

26 September 2024
Metra

Metra AXSP-HK Handleiding

26 September 2024
Metra

Metra 109-TO7 Handleiding

24 September 2024
Metra

Metra 95-8273B Handleiding

6 September 2024
Metra

Metra 95-7822 Handleiding

6 September 2024
Metra

Metra 82-8703 Handleiding

6 September 2024
Metra

Metra 88-00-9004 Handleiding

6 September 2024
Metra

Metra 82-9101 Handleiding

6 September 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd