Metra 70-8116 Handleiding


Lees hieronder de πŸ“– handleiding in het Nederlandse voor Metra 70-8116 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 118 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Match wires below to the matching function of each wire on your receiver (refer to instructions supplied with receiver).
The wire colors of your new receiver may, or may not, match the wire colors of the adaptor. Match adaptor and receiver
wires by function, disregarding color.
Connect Black wire to Ground wire of new receiver.
Individually tape off any unused wires.
Make final wiring connections following instructions on the next page.
Receiver Wiring Adaptor
120 70-8116
Revision 01/10/11
STEP 1 -- CONNECT WIRES
Plug housings into factory harnesses in vehicle.
Before starting, compare items on your invoice with items
received. Thoroughly check packing materials. If an item
is missing, please call:
Crutchfield
*120708116*
ξ˜—
ξ˜—
ξ˜—
IMPORTANT
STEP 2 -- INSTALL
ξ˜—
White - Left Front Speaker Positive
Violet/Black - Right Rear Speaker Negative
Red - 12 Volts Switched Power
Violet - Right Rear Speaker Positive
Green - Left Rear Speaker Positive
Yellow - 12 Volts Constant Power
Gray - Right Front Speaker Positive
Gray/Black - Right Front Speaker Negative
Green/Black - Left Rear Speaker Negative
White/Black - Left Front Speaker Negative
Black - Chassis Ground
Blue - Power Antenna
Copyright 2011 Crutchfield Corporation
R
Green/White - Subwoofer Positive Coil 1
White/Red - Subwoofer Negative Coil 1
Brown/Blue - Subwoofer Negative Coil 2 Brown/Yellow - Subwoofer Positive Coil 2
Wires in this plug are illustrated as
short, but are actually 17 feet long.
Note: The subwoofer wires are not used and should be taped off for the Celica,
Camry, Highlander and Solara. The 2003-04 Avalon uses only the sub coil #1
wires. Both sets of subwoofer wires are used for the Landcruiser.
Note: In order to use the factory subwoofers, we recommend a low-power amp
(50W or less) with a low-pass crossover. Connecting these wires directly to an
aftermarket receiver's speaker leads will produce unsatisfactory results.
at 1-888-955-6000
Tools Required
Soldering
Iron
Solder
(Rosin Core
Suggested)
Electrical
Tape
Receiver Wiring Adaptor Connections
C. Solder:
1. Heat wire.
2. Touch solder to wire, not to iron.
Page 2
Tools Required
Crimp Tool/
Wire Stripper
Crimp Caps
A. Strip wires back 1/2”.
B. Twist wires together and
insert in crimp cap.
C. Squeeze middle of cap
for tight connection.
A. Strip wires back 1/2”.
B. Twist wires together.
D. Tape
CRIMP METHOD SOLDER METHOD
120 70-8116
ξ˜™
ξ˜™
Copyright 2011 Crutchfield Corporation
R


Product specificaties

Merk: Metra
Categorie: Niet gecategoriseerd
Model: 70-8116

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 70-8116 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Metra

Metra

Metra 95-7022HG Handleiding

12 November 2024
Metra

Metra 95-7642 Handleiding

12 November 2024
Metra

Metra 71-017C Handleiding

26 September 2024
Metra

Metra AXSP-HK Handleiding

26 September 2024
Metra

Metra 109-TO7 Handleiding

24 September 2024
Metra

Metra 95-8273B Handleiding

6 September 2024
Metra

Metra 95-7822 Handleiding

6 September 2024
Metra

Metra 82-8703 Handleiding

6 September 2024
Metra

Metra 88-00-9004 Handleiding

6 September 2024
Metra

Metra 82-9101 Handleiding

6 September 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd