Metra 70-5000 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 70-5000 (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3
Match wires below to the matching function of each wire on your receiver (refer to instructions supplied with receiver). The wire colors of your
new receiver may, or may not, match the wire colors of the adaptor. Match adaptor and receiver wires by function, disregarding color.
Your receiver illumination wire could be Orange or Orange/White. As with other wires, match this wire to the illumination wire in this harness
by function, not by color. If your receiver does not have an illumination wire, tape off the illumination wire.
Individually tape off any unused wires.
Make final wiring connections following instructions on page 3.
Receiver Wiring Adaptor
120 70-5000
Revision 02/13/18
STEP 1 -- MATCH & CONNECT WIRES
*120705000*
IMPORTANT
Before starting, compare items on your invoice with items
received. Thoroughly check packing materials. If an item
is missing, please call Crutchfield at 1-888-955-6000.
Copyright 2018 Crutchfield Corporation
Power Harness - Set #1
(see the next page for Harness Set #2)
Yellow - 12 Volts Constant Power
Note: If your vehicle does not have a constant 12V connection, it will be
necessary to run a fused wire to the battery or appropriate fuse in the vehicle.
Red - 12 Volts Switched Power
White - Left Front Speaker Positive
Blue - Power Antenna
Violet - Right Rear Speaker PositiveGreen - Left Rear Speaker Positive
Gray - Right Front Speaker Positive
Gray/Black - Right Front Speaker NegativeWhite/Black - Left Front Speaker Negative
Violet/Black - Right Rear Speaker NegativeGreen/Black - Left Rear Speaker Negative
Orange/White - Illumination
A.
B.
C.
D.
Speaker Harness - Set #1
(see the next page for Harness Set #2)
Note: This wiring harness contains two sets of wiring adaptors.
Please use the set that matches the harnesses in your vehicle.
Note: Connect the receiver ground to the
vehicle chassis for harness set 1 applications.
Match wires below to the matching function of each wire on your receiver (refer to instructions supplied with receiver). The wire colors of your
new receiver may, or may not, match the wire colors of the adaptor. Match adaptor and receiver wires by function, disregarding color.
Your receiver illumination wire could be Orange or Orange/White. As with other wires, match this wire to the illumination wire in this harness
by function, not by color. If your receiver does not have an illumination wire, tape off the illumination wire.
Individually tape off any unused wires.
Make final wiring connections following instructions on page 3.
Receiver Wiring Adaptor
120 70-5000
Copyright 2018 Crutchfield Corporation
STEP 1 -- MATCH & CONNECT WIRES (CONTINUED)
A.
B.
C.
D.
Red - 12 Volts Switched Power
Blue - Power Antenna
Orange/White - Dimmer (Not Used - Tape Off)
Orange - Illumination
Black - Chassis Ground
Blue/White - Amplifier Turn-On
White - Left Front Speaker Positive
Green - Left Rear Speaker Positive
White/Black - Left Front Speaker Negative
Green/Black - Left Rear Speaker Negative
Violet/Black - Right Rear Speaker Negative
Violet - Right Rear Speaker Positive
Gray - Right Front Speaker Positive
Gray/Black - Right Front Speaker Negative
Orange/Black - (not used - tape off)
Page 2
Power Harness - Set #2 Speaker Harness - Set #2
Yellow - 12 Volts Constant Power
Note: If your vehicle does not have a constant 12V connection, it will be
necessary to run a fused wire to the battery or appropriate fuse in the vehicle.
Note: If your vehicle does not have a ground connection,
connect the ground wire from the new receiver to chassis ground.
120 70-5000
Page
STEP 2 -- CONTINUED
A. Strip wires back 1/2”.
B. Twist wires together and
insert in crimp cap.
C. Squeeze middle of cap
for tight connection.
Copyright 2018 Crutchfield Corporation
STEP 3 -- APPLICATION
D. Complete crimp connections
for all necessary wires.
E. Be sure to wrap any wires from
the Wiring Adaptor that are
not necessary (wires with no
match from the new receiver)
with electrical tape.
STEP 2 -- CRIMP CONNECTIONS
Tools & Parts
Required
Wire Stripper/Crimp Tool Crimp Caps
Unused Wire (tape over bare wires)
Receiver Wiring Adaptor
Generic Illustration
Generic Illustration
Receiver Wiring Adaptor Connections
A. When ready to install the
receiver, plug the wiring
Adaptor from the new receiver,
or receiver assembly into the
factory radio harness(es) in the
vehicle dash.
3


Product specificaties

Merk: Metra
Categorie: Niet gecategoriseerd
Model: 70-5000

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 70-5000 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Metra

Metra

Metra 95-7022HG Handleiding

12 November 2024
Metra

Metra 95-7642 Handleiding

12 November 2024
Metra

Metra 71-017C Handleiding

26 September 2024
Metra

Metra AXSP-HK Handleiding

26 September 2024
Metra

Metra 109-TO7 Handleiding

24 September 2024
Metra

Metra 95-8273B Handleiding

6 September 2024
Metra

Metra 95-7822 Handleiding

6 September 2024
Metra

Metra 82-8703 Handleiding

6 September 2024
Metra

Metra 88-00-9004 Handleiding

6 September 2024
Metra

Metra 82-9101 Handleiding

6 September 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd