Metra 70-1787C Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 70-1787C (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 15 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3
IMPORTANT
The function of the RED and YELLOW wires is
reversed for the vehicles listed below. Yellow
connects to Ignition and Red connects to 12V
Constant.
1997-'02 Porsche Boxster
1999-'01 Porsche 911
!
Receiver Wiring Adaptor
120 70-1787
Revision 08/11/14
*White - Left Front Speaker Positive
***Red - 12 Volts Switched Power
***Yellow - 12 Volts Constant Power
*Gray - Right Front Speaker Positive
*Gray/Black - Right Front Speaker Negative
***Orange - Illumination
*White/Black - Left Front Speaker Negative
***Black - Chassis Ground
***Blue - Power Antenna
STEP 1 -- CONNECT WIRES
*120701787*
IMPORTANT
Before starting, compare items on your invoice with items
received. Thoroughly check packing materials. If an item
is missing, please call Crutchfield at 1-888-955-6000.
***Blue/White - Amplifier Turn-On
**White - Left Front AMP Input
***Violet - Right Rear AMP Input
***Green - Left Rear AMP Input
**Gray - Right Front AMP Input
WIRE APPLICATION GUIDE
* Use in vehicles without factory-equipped
Premium or Bose system.
** Use in vehicles with factory Premium or
Bose system.
*** Use in vehicles with either system.
NOTE: The long red wire included applies to certain vehicles that require a switched power source at the fuse panel. See page 2 for specific applications.
Long Red Wire - See page 2 for applications.
*Asterisks denote referral to Wire Application Guide below.
Copyright 2014 Crutchfield Corporation
Match wires below to the matching function of each wire on your receiver (refer to instructions supplied with receiver).
The wire colors of your new receiver may, or may not, match the wire colors of the adaptor. Match adaptor and receiver wires by function,
disregarding color.
If your receiver does not have a Dimmer or Illumination wire, tape off the Orange wire.
Connect the Black wire to the Ground wire of the new receiver.
Individually tape off any unused wires.
Make final wiring connections following instructions on page 3.
A.
B.
C.
D.
E.
NOTE: These instructions pertain to the use of the additional long red wire in vehicles requiring
a 12 Volt switched power source at the vehicle's fuse panel.
All other wires are connected as instructed on page 1 unless otherwise specified.
*White - Left Front Speaker Positive
***Red - 12 Volts Switched Power
***Yellow - 12 Volts Constant Power
*Gray - Right Front Speaker Positive
*Gray/Black - Right Front Speaker Negative
***Orange - Illumination
*White/Black - Left Front Speaker Negative
***Black - Chassis Ground
***Blue - Power Antenna
***Blue/White - Amplifier Turn-On
**White - Left Front AMP Input
***Violet - Right Rear AMP Input
***Green - Left Rear AMP Input
**Gray - Right Front AMP Input
Receiver Wiring Adaptor
120 70-1787
Red - 12 Volts Switched Power
Fuse Clip
Using the Long Red Wire (if applicable):
Run the long wire from the receiver to the fuse panel. Make sure wire is safely
secured away from moving parts. Locate the correct fuse referring to the wire
application guide on this page. Remove the fuse. Use a test meter to
determine the "power" side of the fuse slot. Connect the fuse clip to one
prong of the fuse. Reinstall the fuse so that the clip/prong is on the opposite
side that connects to power. It is important that the clip is on the cor-NOTE:
rect side in order for the line to be protected by the fuse.
LONG RED WIRE APPLICATION GUIDE
2006-'07 Audi A3 #42 - 15 amp Left Side Dash End Cap
2002-'04 Audi A4 #36 - 30 amp Left Side Dash End Cap
2002-'04 Audi A6 #24 - 25 amp Left Side Dash End Cap
2002-'05 Audi AllRoad #24 - 25 amp Left Side Dash End Cap
2004 Audi S4 #36 - 30 amp Left Side Dash End Cap
2002-'04 Audi TT #24 - 20 amp Left Side Dash End Cap
VEHICLE FUSE LOCATION
Page 2
Clip placed on fuse
*Asterisks denote referral to Wire Application Guide on page 1.
Copyright 2014 Crutchfield Corporation
Receiver Wiring Adaptor Connections
120 70-1787
Page 3
STEP 2 -- CONTINUED
A. Strip wires back 1/2”.
B. Twist wires together and
insert in crimp cap.
C. Squeeze middle of cap
for tight connection.
STEP 3 -- APPLICATION
When ready to install the receiver, plug
the Wiring Adaptor from the new receiver
or receiver assembly into the factory
radio harness(es) in the vehicle dash.
D. Complete crimp connections
for all necessary wires.
E. Be sure to wrap any wires from
the Wiring Adaptor that are
not necessary (wires with no
match from the new receiver)
with electrical tape.
STEP 2 -- CRIMP CONNECTIONS
Tools & Parts
Required
Wire Stripper/Crimp Tool Crimp Caps
Unused Wire (tape over bare wires)
Receiver Wiring Adaptor
Generic Illustration
Generic Illustration
Copyright 2014 Crutchfield Corporation


Product specificaties

Merk: Metra
Categorie: Niet gecategoriseerd
Model: 70-1787C

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 70-1787C stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Metra

Metra

Metra 95-7022HG Handleiding

12 November 2024
Metra

Metra 95-7642 Handleiding

12 November 2024
Metra

Metra 71-017C Handleiding

26 September 2024
Metra

Metra AXSP-HK Handleiding

26 September 2024
Metra

Metra 109-TO7 Handleiding

24 September 2024
Metra

Metra 95-8273B Handleiding

6 September 2024
Metra

Metra 95-7822 Handleiding

6 September 2024
Metra

Metra 82-8703 Handleiding

6 September 2024
Metra

Metra 88-00-9004 Handleiding

6 September 2024
Metra

Metra 82-9101 Handleiding

6 September 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd