Match UP 7DSP Handleiding

Match Niet gecategoriseerd UP 7DSP

Lees hieronder de 📖 handleiding in het Nederlandse voor Match UP 7DSP (17 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 41 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/17

UP 7DSP

U P G R A D E

7-Kanal Upgrade-Verstärker mit integriertem 8-Kanal

64 Bit DSP für universelle Anwendungen

7-channel upgrade amplier with integrated 8-channel

64 Bit DSP for universal applications

deutsch / english

Dear Customer,

Congratulations on your purchase of this innovative

and high-qual ity MATCH product.

Thanks to more than 30 years of experience in

research and development of audio products this

amplier sets new standards in the range of digital

ampliers.

We wish you many hours of enjoyment with your

new MATCH UP 7DSP.

Yours,

AUDIOTEC FISCHER

General installation instructions for MATCH

components

To prevent damage to the unit and possible injury,

read this manual carefully and follow all installation

instructions. This product has been checked for

proper function prior to shipping and is guaranteed

against manufacturing defects.

Before starting your installation, disconnect the

battery’s negative terminal to prevent damage

totheunit,reand/orriskofinjury.For a proper

performance and to ensure full warranty coverage,

we strongly recommend to get this product installed

by an authorized MATCH dealer.

Install your UP 7DSP in a dry location with sufcient

air circulation for proper cooling of the equipment.

For safety reasons, the UP 7DSP must be profes-

sionally installed. Therefore, use the two mounting

plates which are included in delivery. These are at-

tached to the bottom of the amplier with two short

screws which are included in delivery, too.

When screwing the amplier to the vehicle chassis,

carefully examine the area around and behind the

proposed installation location to ensure that there

are no electrical cables or components, hydraulic

brake lines or any part of the fuel tank located be-

hind the mounting surface. Failure to do so may re-

sult in unpredictable damage to these components

and possible costly repairs to the vehicle.

General instruction for connecting the UP 7DSP

amplier

The UP 7DSP amplier may only be installed in mo-

tor vehicles which have a 12 Volts negative terminal

connected to the chassis ground. Any other system

could cause damage to the amplier and the electri-

cal system of the vehicle.

The positive cable from the battery for the entire

sound system should be provided with a main fuse

at a distance of max. 30 cm from the battery. The

value of the fuse is calculated from the maximum

total current draw of the car audio system.

Use only the included MATCH cable or

the optional PP-ISO cable for connec-

tion of the UP 7DSP. The use of other

cables can result in damage of the ampli-

er, the headunit/carradio ortheconnected

loudspeakers! The fuses of the amplier may

only be replaced by identically rated fuses

(2x25A)toavoiddamageoftheamplier.

Prior to installation, plan the wire routing to avoid

any possible damage to the wire harness. All

cabling should be protected against possible

crushing or pinching hazards. Also avoid routing

cables close to potential noise sources such as

electric motors, high power accessories and other

vehicle harnesses.

Congratulations!

General instructions

Connectors and control units

1 Auto Remote

This switch allows to activate / deactivate the

automatic turn-on feature of the amplier

2 System Connector 2

Connector for loudspeakers and / or sub-

woofers.

3 Clipping LED

This LED lights up red if one of the analog

inputs is overdriven.

4 System Connector 1

Connector for the UP 7DSP cable harness.

Only use the supplied connection cable to

connect the amplier to the car radio.

5 Fuse LED

This LED will light up if the fuses inside the

amplier are blown.

6 +12 V

Connector for the +12 V power cable to the

positive terminal of the battery.

7 GND

Connector for the ground cable (negative

terminal of the battery or metal body of the

vehicle).

8 REM

Connector for the remote cable.

1 2 3 4 5 6 7 8

9 USB Input

Connects the UP 7DSP to your PC.

10 Control pushbutton

Use this button to either switch between the

setups or initiate a reset of the device.

11 Status LED

This LED indicates the operating mode of

the amplier and the setup that has been

chosen.

12 Control Input

Multifunction interface for e.g. an optional

remote control or other MATCH UP 7DSP

accessory.

13 Optical Input

Optical input for digital stereo signals (SPDIF

format).

14 Gain

Control for adjusting the input sensitivity.

15 Remote Out

The remote output has to be used to turn on /

off external ampliers that are connected to

the .Line Out

16 Line Out

Mono line output for connecting external am-

pliers. Make sure that the remote output is

used to turn on these devices.

10 119 16151312 14

Product specificaties

Merk:	Match
Categorie:	Niet gecategoriseerd
Model:	UP 7DSP

Heb je hulp nodig?

Als je hulp nodig hebt met Match UP 7DSP stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Match

Match UP 7BMW Handleiding

5 Juni 2023

Match UP 7DSP Handleiding

3 Juni 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Panasonic DMW-AVC1 Handleiding

24 November 2024

Panasonic DMW-GMC1 Handleiding

24 November 2024

Philips HX6907 Handleiding

23 November 2024

Philips EasyShine BHN368 Handleiding

23 November 2024

Philips CD74R Handleiding

23 November 2024

Philips DVDRW1S04 Handleiding

23 November 2024

Philips CDR24D24H Handleiding

23 November 2024

Philips SWV3034S Handleiding

23 November 2024

Philips DLP2015 Handleiding

23 November 2024

Philips VisaPure SC6026 Handleiding

23 November 2024