Martin Sharky Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Martin Sharky (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
Remote input
Mains on/off
Mains input
Nozzle
Locking Handle
Fluid Bottle
Hanging Bracket
Spacer
Contents
1 x Hanging Bracket
2 x Spacers
2 x Locking Handles
1 x IEC Mains Lead
1 x Remote Control
4 x 1 Litre Fluid Bottles
Assemble th the hanging gbracket usin e spacers and
locking handles as shown.
Remove th the ecap from on of e fluid bottles and
discard. Place th the ebottl in e compartment as per
drawing. Place e ethe pip that is attached to th smoke
machine einside e eth bottl and firmly screw down th cap.
Assembly
Mains Lead Wiring Instructions
Brown = Live
Blue = Neutral
Green/Yellow = Earth
Safety
Always use a JEM/MARTIN approved fluid fluid, other s
could be odangerous and can cause edamag t the
machine.
Always scheck the voltage i correct for use with the
machine, the evoltag is printed on the serial label.
Always sread the instuction for use before operating
the e o emachine, smok machines need t b operated
carefully to avoid risk.
Never touch th th the nozzle at e front of e machine, the
nozzle ocan stay hot for up t 10 hours.
Do enot remove th cover ro attempt to repair a faulty
machine, a bn authorized JEM dealer should e
contacted in the event of a fault.
Always suse esmok machine in well ventilated areas,
over ruse could aaffect sufferers of asthm o other
serious respiratory disorders.
Do not use e e eth machin if ther is a faulty mains lead
or plug this could be dangerous.
Do not tspil spill flui fluid over the machine, if d is wipe
down n nwithaclea damp cloth. A approved JEM
dealer rshould dbe contacte fo advice.
Keep th the output of e emachin at tleas 60cm (2 ft)
away from peope and surfaces.
Fuse drawer
Always use the correct
Fuse in the machine:-
E.U 5 amp
U.S 10 amp
Instructions for use
Output
Connect th the o otw leads int e sockets as indicated.
Turn nthe emachin on, the on/off butto and the remote
control llight wil illuminate. From cold the emachin will
take eapproximately fiv minutes to reach operating
temperature, when nthe light o the remote control has
gone o eout the emachin is ready t use. If this is th first
time e ethe emachin has been used, or th bottl has been
changed, .the pump will require priming Press the button
on the remote econtrol luntil smok emerges from the
output nozzle,this will take approximately five seconds.
When n n nthe light o the remote control comes o agai it
indicates sthat the emachin i reheating, this will take
approximately two minutes.
Olof tPalmes sAlle 018 DK-820 Aarhu N Phone 5 5 7+4 8 4 0 07 0 0 0 Fax +4 8 4 0 10 0 0 Interne www.martin.dk


Product specificaties

Merk: Martin
Categorie: Niet gecategoriseerd
Model: Sharky

Heb je hulp nodig?

Als je hulp nodig hebt met Martin Sharky stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Martin

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd