Martin MAC 700 Wash Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Martin MAC 700 Wash (40 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 54 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/40
MAC 700 Wash
user manual
Dimensions
All measurements are expressed in millimeters
270°
270°
270°
270°270°
143
143
143
143143
390
390
390
390390
515
515
515
515515
656
656
656
656656
450
450
450
450450
365
365
365
365365
675
675
675
675675
285
285
285
285285
120°
120°
120°
120°120°
565
565
565
565565
Min. c/c 530
Min.
Min.
Min.
Min. c/c
c/c
c/c
c/c 530
530
530
530
270°
270°
270°
270°270°
120°
120°
120°
120°120°
12.5
12.5
12.5
12.5
12.5°
°
°
°°
66
66
66
66
66°
°
°
°°
© 2006-2007 Martin Professional A/S, Denmark. All rights reserved. No part of this manual may be reproduced, in any form or by any
means, without permission in writing from Martin Professional A/S. Information subject to change without notice. Martin Professional
A/S and all affiliated companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any
other loss occasioned by the use of, inability to use or reliance on the information contained in this manual.
P/N 35000185, Rev. D
Safety information
Warning! This product is for professional use only. It is not for household use.
This product presents risks of lethal or severe injury due to fire and heat, electric shock, ultraviolet radiation,
lamp explosion, and falls. Read this manual before powering or installing the fixture, follow the safety
precautions listed below and observe all warnings in this manual and printed on the fixture. If you have
questions about how to operate the fixture safely, please contact your Martin dealer or call the Martin
24-hour service hotline at +45 70 200 201.
P R O T E C T I O N F R O M E L E C T R I C S H O C K
Disconnect the fixture from AC power before removing or installing the lamp, fuses, or any part, and when
not in use.
Always ground (earth) the fixture electrically.
Do not use the fixture with a damaged power cable or power plug.
Use only power cable specified as extra hard usage
Do not attempt to bypass fuses. Replace defective fuses with ones of the specified type and rating only.
Use only a source of AC power that complies with local building and electrical codes and has both
overload and ground-fault (earth-fault) protection.
Do not expose the fixture to rain or moisture.
Refer any service operation not described in this manual to a qualified technician.
L A M P S A F E T Y
Do not operate the fixture with missing or damaged covers, shields, lenses or ultraviolet screens.
A hot discharge lamp is under pressure and can explode without warning. Allow the fixture to cool for at
least 45 minutes and protect yourself with safety glasses and gloves before replacing the lamp or
servicing the fixture internals.
Do not stare directly into the light output. Never look at an exposed lamp while it is lit.
Replace the lamp if it becomes visually deformed, damaged or in any way defective
Replace the lamp at the latest when it reaches the limit of its average life as specified in this manual or by
the lamp manufacturer.
Install only an approved lamp.
If the quartz envelope of a discharge lamp is broken, the lamp releases a small quantity of mercury and
other toxic gases. If a discharge lamp explodes in a confined area, evacuate the area and ventilate it
thoroughly. Wear nitrite gloves when handling a broken discharge lamp. Treat broken or used discharge
lamps as hazardous waste and send to a specialist for disposal.
P R O T E C T I O N F R O M B U R N S A N D F I R E
Danger! Intense heat. Avoid contact by persons and materials.
The exterior of the fixture can get very hot up to 160° C (320° F). Allow the fixture to cool
for at least 45 minutes before handling.
Prolonged exposure to an unshielded lamp can cause eye and skin burns.
Do not attempt to bypass thermostatic switches or fuses. Replace defective fuses with ones of the
specified type and rating only.
Keep all combustible materials (for example fabric, wood, paper) at least 0.5 meters (20 inches) away
from the fixture. Keep flammable materials well away from the fixture.
Do not illuminate surfaces within 1.2 meters (42 inches) of the fixture.
Provide a minimum clearance of 0.1 meters (4 inches) around fans and air vents.
Do not place filters or other materials over the lens.
The exterior of the fixture becomes hot. Allow the fixture to cool for at least 45 minutes before handling.
Do not use the fixture if any cable, component or cover is damaged, cracked or deformed.
Do not modify the fixture in any way not described in this manual.
Install only genuine Martin parts.
Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).


Product specificaties

Merk: Martin
Categorie: Niet gecategoriseerd
Model: MAC 700 Wash

Heb je hulp nodig?

Als je hulp nodig hebt met Martin MAC 700 Wash stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Martin

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Senal

Senal ME-220-CL Handleiding

21 November 2024
Senal

Senal ASM-4 Handleiding

21 November 2024
Senal

Senal CS-88 Handleiding

21 November 2024
Senal

Senal CSP-162 Handleiding

21 November 2024
Senal

Senal ASM-3 Handleiding

21 November 2024
Senal

Senal ASM-5 Handleiding

21 November 2024
Senal

Senal PS-48B Handleiding

21 November 2024
D-Link

D-Link DWA-142 Handleiding

21 November 2024
Senal

Senal CSP-142 Handleiding

21 November 2024
Senal

Senal SCI-3212 Handleiding

21 November 2024