Martin DJ Spinner Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Martin DJ Spinner (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 208 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
Spinner
users guide
INTRODUCTION
The Martin Professional is a powerful but compact lighting eectDJ Series Spinner
producing a stunning and colourful display. The Spinner features:
300 W / 120 V halogen (DRA) or 300 W / 230 V halogen lamp according to the model
(115 V / 230 V).
Bright light output.
Colours produced from dichroic lters.
Sound activated beam pattern and colour change.
Light can be continuously on or sound activated.
Built-in microphone with automatic gain control (A.G.C.).
Eective fan cooling.
Adjustable mounting bracket.
Can be controlled in multiples by a lighting controller.
HOW TO INSTALL THE SPINNER
Before operating the Spinner, you will need to install the lamp and t a plug on the mains
lead. Please do as follows:
IMPORTANT
Before attempting any of the following please ensure that the unit is
disconnected from any mains power.
Remove the nger screw on the lid located on the back of the unit and withdraw the
lamp-socket assembly.
Hold the lamp by the ceramic parts or hold in a clean cloth, taking care not to touch the
glass, and then push the lamp rmly into the lamp-socket. If you do touch the glass part
of the lamp you must clean it thoroughly with alcohol before use. Ensure that the lamp
matches the voltage and wattage specications listed in the ’Technical Specications’
table on page 3.
Insert the lamp into the reector by replacing the lamp-socket assembly, and then tighten
the nger screw.
The Spinner may be delivered from factory without any plug on the mains lead. You must
t a suitable plug (one that ts your local wall outlet) before you can connect the unit to
the mains. The double isolated mains lead on the Spinner contains three wires. The
brown wire should be connected to LIVE, the blue wire to NEUTRAL, and the
Yellow/Green wire to EARTH (ground).
You can now install the Spinner in the desired position. The mounting bracket allows you
to tilt and turn the unit.
2
OPERATING THE SPINNER
Located on the rear panel of the Spinner is a three way function switch. Choose any of the
switch positions and power up the Spinner. You will now see one of three performances
according to the function selected:
Both light, beam pattern and colour change are sound activated.
Light is continuously o.
Light is continuously on but beam pattern and colour change are sound activated.
The sounds are picked up by a built-in microphone and a special electronic circuit - the
Automatic Gain Control - serves to adjust the gain when the average sound pressure alters.
IMPORTANT
The voltage applied to both the halogen lamp and the motor in the Spinner is
provided by an electronic circuit. For this reason, you should not attempt to dim
the Spinner by means of a dimmer pack or any similar equipment. Otherwise,
damage might occur to the Spinner. However, it is legal to use the full on and full
o
levels on the dimmer pack as well as using a switch pack to remotely
switch on and o the Spinner.
TECHNICAL SPECIFICATIONS
Overall dimensions: Please see gure 1 on page 4
Weight: 4 Kg
Power consumption: 325 W
Mains voltage 115 V model:
Mains voltage 230 V model:
100 - 130 V
220 - 240 V
Mains frequency: 50 - 60 Hz
Lamp 115 V model:
Lamp 230 V model:
DRA 300 W / 120 V (Osram 64514)
300 W / 230 V (Osram 64516)
Fuse: F4 A at 100 - 130 V
F2 A at 220 - 240 V
3


Product specificaties

Merk: Martin
Categorie: Niet gecategoriseerd
Model: DJ Spinner

Heb je hulp nodig?

Als je hulp nodig hebt met Martin DJ Spinner stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Martin

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd