Martin Centrepiece Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Martin Centrepiece (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 48 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
Centrepiece
users guide
CONTENTS
INTRODUCTION ................................................. 2
SELECTING MAINS VOLTAGE AND FREQUENCY . . . . . . . . . . . . . . . . . . . . . . . . 3
MOUNTING THE ROTATING MIRRORWHEEL . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
MOUNTING THE LAMP INSIDE THE CENTREPIECE . . . . . . . . . . . . . . . . . . . . . . 4
OPERATING WITHOUT A CONTROLLER (STAND ALONE) . . . . . . . . . . . . . . . . . . 4
OPERATING "STAND ALONE" IN MASTER/SLAVE MODE . . . . . . . . . . . . . . . . . . 4
REMOTE CONTROLLED BLACK-OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
OPERATING WITH A CONTROLLER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SWITCHING THE LAMP ON AND OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SEQUENTIAL START OF THE MSR 1200 LAMPS . . . . . . . . . . . . . . . . . . . . . . . . . 5
DIP SWITCH SETTINGS FOR THE CENTREPIECE . . . . . . . . . . . . . . . . . . . . . . . . 6
TECHNICALSPECIFICATIONS....................................... 7
INTRODUCTION
The Centrepiece is a high performance, intelligent lighting eect which features:
1200 Watt MSR discharge lamp with an average 1000 hours lamp life.
8 dichroic colours in a carousel with micro-stepping resolution and optical indexing.
Continuous rotation or absolute position, including colour mix. Operates with acceleration
control.
Zap-like mirrorwheel for scattering beams. The mirrorwheel operates with micro-stepping
resolution and acceleration control.
8 controllable tilt-mirrors for projecting the beams downwards or onto the mirrorwheel.
High-quality lenses providing high light output.
Ecient fan cooling.
Can be controlled by the Martin Controllers: 3032 (128 pcs.), 2032 (32 pcs.), 2208/2308
(8 pcs.) and 2501 (32 pcs.).
Can be controlled via DMX 512 with the Martin DMX-Interface.
Built-in pre-program or random chases with or without music trig.
Phase compensation circuit provides high power factor (low current consumption).
Selectable voltage and frequency.
Page 2
SELECTING MAINS VOLTAGE AND FREQUENCY
To ensure proper and safe operation of your Centrepiece, it is most important that the
transformer and ballast are wired correctly for your local mains voltage and frequency. The
factory setting is printed on the serial number label which is located on the top of the unit,
but please ensure that this setting matches your local mains supply.
It is possible, however, to rewire the unit according to your local mains voltage and
frequency by following the procedure below. The mains transformer can be wired to 100,
120, 215, 230 or 250 Volts and the ballast to 50 or 60 Hz.
IMPORTANT !
BEFORE ATTEMPTING ANY OF THE FOLLOWING PLEASE ENSURE THAT THE
UNIT IS DISCONNECTED FROM ANY MAINS AC POWER
Place the Centrepiece on one of the sides so that the arrow on the wiring label points
upwards.
Unscrew the eight screws which secure the upper side-cover to the top- and bottom-plate
and then remove the side-cover.
Locate the mains transformer with the white screw terminals. Please note that the values
for voltage and frequency on these terminals are not printed on the transformer but on
the wiring label.
Move the brown voltage wire marked by a yellow ’V’ to the required voltage terminal.
Move the brown frequency wire marked by a yellow ’F’ to the required frequency terminal.
Mount the side-cover back onto the unit before switching on.
MOUNTING THE ROTATING MIRRORWHEEL
Place the Centrepiece so that it rests on one of the sides.
Place the mirrorwheel onto the motor axle which is located at the bottom on the
Centrepiece. Move the mirrorwheel towards the bottom-plate until the distance between
mirrorwheel and the bottom-plate is about 2 cm.
Secure the mirrorwheel by carefully tightening the two allen-screws on the mirror-wheel
and inserting the split pin through the hole in the axle.
Page 3


Product specificaties

Merk: Martin
Categorie: Niet gecategoriseerd
Model: Centrepiece

Heb je hulp nodig?

Als je hulp nodig hebt met Martin Centrepiece stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Martin

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd