Martin 2501 Controller Handleiding

Martin Niet gecategoriseerd 2501 Controller

Lees hieronder de 📖 handleiding in het Nederlandse voor Martin 2501 Controller (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
Martin 2501 Controller
user’s guide
Software version 5.0
Table of Contents
Introduction ..................................................... 3
Connections ..................................................... 3
Sections of the 2501 Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Accessing Stand-Alone and Pre-Programmed sequences . . . . . . . . . . . . . . . . . . . . 5
Stand-AloneSequences ............................................ 5
Pre-ProgrammedSequences ......................................... 6
Current Controller version and Software Requirements for Units . . . . . . . . . . . . . . . 7
UnitDipSwitchSettings ............................................ 8
Martin Professional 2501 Controller Users Guide Page 2
Introduction
The 2501 controller is a simple but eective controller from Martin Professional. The 2501
controller can give access to all of the basic color change functions within all of the Martin
Professional range of Intelligent products (not Roboscan Pro 1220), as well as having the
additional facility to be able to access all of the stand - alone programs within the units that
are connected to the controller. All of this is possible by just a few key presses on the
controller.
The 2501 controller is able to control all of the Martin Professional range of intelligent
products in any combination, up to a maximum of 32 units per controller. There are no limits
on the type and variety of units that you choose to connect to the controller whatsoever.
Connections
Before switching on, ensure that the voltage selector switch is set for your local power
supply and if necessary connect a Three pin plug to the mains cable using the Brown wire
for the Live connection, the Blue wire for the Neutral connection and the Green/Yellow wire
for the Earth (Ground) connection.
When connecting the controller to the Unit
use the XLR cable that came with the
controller to connect the controller to the
rst Unit on the link. Now link up the rest of
the Units with XLR cables. These can be
supplied by your local Martin dealer or you
can use standard 3-core balanced
microphone cable. Remember to insert the
terminating-plug that came with the
controller into the last Unit in the link. This
will be necessary to ensure correct and
error-free communication between the Units
and the Martin 2501 controller.
To turn the controller on press the red switch on the left hand side of the unit from the O
position to the On position. If there is a good power supply going to the unit this switch will
light up and a hard reset signal will be sent to all units in the link, please note that this is the
only way to perform a hard reset on the units in the link.
Martin Professional 2501 Controller Users Guide Page 3


Product specificaties

Merk: Martin
Categorie: Niet gecategoriseerd
Model: 2501 Controller

Heb je hulp nodig?

Als je hulp nodig hebt met Martin 2501 Controller stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Martin

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Festo

Festo VPPI Handleiding

21 November 2024
Festo

Festo SFAB Handleiding

21 November 2024
Festo

Festo SFAH Handleiding

21 November 2024
Festo

Festo DRRD-12 Handleiding

21 November 2024
Festo

Festo SDE3 Handleiding

21 November 2024
Festo

Festo SFTE Handleiding

21 November 2024