Marantec Command 231 Handleiding
Marantec
Garagepoortopener
Command 231
Lees hieronder de 📖 handleiding in het Nederlandse voor Marantec Command 231 (2 pagina's) in de categorie Garagepoortopener. Deze handleiding was nuttig voor 145 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
Command 231
Radio code keypad for impulse control
Version
Command 231 868 MHz (Art.-No. 68 328)
Command 231 433 MHz (Art.-No. 68 333)
Safety advice
Attention:
• Please read these instructions carefully
before connecting and operating this
device!
• Have faulty and defective devices checked
by the manufacturer.
• You are not authorized to carry out
changes to this device.
Function
The radio code keypad offers you the possibility to
open and close your garage door by entering a
4-digit personal identification number (PIN). It can
be programmed, so that up to 3 garage door
operators can be actuated with a different code
each or one garage door operator can be actuated
with up to three different PIN's. Additionally any
number can be programmed temporarily as PIN in
order to grant a temporary access for certain visitors
or service personnel.
Beside this an additional device (e.g. the yard light)
can be controlled. For this function ("light function")
a further receiver is required.
Installation of the radio code keypad
• Choose a suitable place to install the radio code
keypad.
• Take the wall bracket as pattern and mark the
place for the two drill holes. Then drill the holes
and insert the enclosed wall plugs.
• Screw on the wall bracket by means of the
enclosed screws. For surfaces other than wood
other screws and wall plugs may be necessary.
• Click the radio code keypad into the wall bracket.
• Take a coin to turn the lock on the bottom side of
the wall bracket clockwise to fix the radio code
keypad.
Enter PIN and transmit code
Your radio code keypad is delivered with
1 random code and 1 PIN already programmed.
The factory programmed PIN is 1-2-3-4.
Attention:
To program the third code the preset
code (random programming) must be
overwritten with the PIN 1-2-3-4 and
then the PIN 1-2-3-4 must be changed
according to the instructions.
In case you already use another radio transmitter to
control your garage door operator, the code of this
has to be transmitted from the transmitter to the
actual radio code keypad.
Transmit the code for the garage door control
from one transmitter to the radio code keypad:
• Connect the radio code keypad and the actual
transmitter by means of the programming plug.
• Hold the button on the transmitter you control
the garage door with.
Press the ENTER button on the radio code keypad.
The keypad lights up.
• Enter a new 4-digit PIN of your choice. Then press
the ENTER button again. Hold the transmitter
button until the LED on the radio code keypad
flashes quickly.
• Now the radio code keypad has learned the
transmitter code and saved under the PIN you
have entered. Now you may remove the
programming plug.
Transmit the code for light function from one
transmitter to the radio code keypad:
The light function is already programmed with a
special code. But you may as well transmit another
transmitter code to actuate the light function.
• Connect the radio code keypad and the actual
transmitter by means of the programming plug.
• Hold the specific button on the transmitter you
activate the other device with. Press the ENTER
button on the radio code keypad. The keypad
lights up.
• Press the LIGHT button and then again the ENTER
button. Hold the transmitter button until the LED
on the radio code keypad flashes quickly.
• The radio code keypad has now learned the new
transmitter code for the light function. Now you
may remove the programming plug.
Save more than 1 code to control more than
1 garage door operator:
• With the radio code keypad you may control up
to 3 different garage door operators, each with a
different code.
• For each of the 3 codes proceed as described
above, but with one exception: You must enter a
different PIN for each code, which means each
code requires an individual PIN.
• To open or close a certain garage door with the
radio code keypad, just enter the respective PIN
and then press the ENTER button.
Save more than 1 PIN for the same code:
Beside the already programmed PIN it is possible to
save up to 2 additional PIN's for the same code and
to assign these PIN's to different persons.
• Follow the instructions described under "Transmit
the code for the garage door control from one
transmitter to the radio code keypad" for every
single PIN. Repeat these steps for each PIN with
the same transmitter. So the same code is saved
under 3 different PIN's.
Save a temporary PIN:
A temporary PIN that is valid only for three actuations
can be saved.
• Hold "button 1" for 3 sec. until the LED flashes
quickly. Enter the currently valid PIN and then
press the ENTER button.
• Enter a temporary 4-digit PIN of your choice and
then press the ENTER button.
• The LED glows up for 2 sec. Then the keypad light
goes off. The radio code keypad is ready for
operation again.
• To use the radio code keypad with the latest
temporary PIN enter the 4-digit temporary PIN and
then press the ENTER button. You are allowed to
use this PIN three times and then it is automatically
cleared.
1
iverî€ Sender
P rstecker
Steckerbuchse
Cover
Keypad light
Socket
Programming plug
Active
transmitter
Mounting holes
Screws
Lock
Coin
Wall bracket
Wall
plug
LED
2
Use of the radio code keypad
To protect the radio code keypad keep the cover
closed when it is not in use.
Switch on the keypad light:
• Press the LIGHT button.
The keypad light is on for 5 sec.
Open and close the garage door:
• Enter the programmed 4-digit PIN and then press
the ENTER button. The garage door starts to
move.
• After having pressed the ENTER button, the radio
code keypad remains active for approx. 18 sec.
and the LED is on. During this period of time you
can stop the garage door by pressing any button
(except the LIGHT button).
• Under certain conditions it may be necessary to
keep one button pressed so that your garage door
control works. In this case enter the 4-digit PIN
and then hold the ENTER button. The garage door
moves as long as the ENTER button is held.
Advice:
In case a PIN longer than 4 digits is entered,
only the last 4 digits are considered as
valid. If three wrong PIN's are entered in
sequence, the radio code keypad cuts off to
prevent unauthorised access. After 2 min.
the radio code keypad is ready for use
again.
Light function (to switch other devices):
• To actuate another device (e.g. switch on the yard
light), press the LIGHT button and then the enter
button.
• To switch off the other device (e.g. the yard light),
press the LIGHT button again and then the ENTER
button.
Change the PIN
• Hold "button 0" for approx. 3 sec. until the LED
flashes quickly.
• Enter the PIN to be changed and then press the
ENTER button.
• Enter the new 4-digit PIN and then press the
ENTER button. The LED is on for 2 sec. (no
flashing).
• The radio code keypad is now ready for operation
with the new PIN (the old PIN is no longer valid).
Clear memory
• Press the LIGHT button.
-> After 3 sec. the LED starts to flash quickly.
• Hold the LIGHT button.
• While holding the button, enter PIN 9-9-9-9.
• Release the LIGHT button.
-> The memory is now cleared.
The LED is on for 2 sec.
Advice:
After clearing the memory the radio code
keypad is programmed with 1 random
code and PIN 1-2-3-4.
Replace batteries
• Take a coin to turn the lock on the bottom side of
the wall bracket anti-clockwise. Then take the
radio code keypad out of the wall bracket.
• Unscrew the back cover of the housing of the
radio code keypad.
• Take out the old batteries.
• Insert 2 new 3V batteries, CR 2032. Observe right
poling. Test the function of the unit (The radio
code keypad is designed that it will recognize all
previously programmed codes and PIN's after
change of battery).
• Screw again the back cover of the housing to the
radio code keypad.
Advice:
Don't dispose of old batteries in the
dustbin! Return them to your dealer or
dispose of in a recycling container for used
batteries.
Technical details
Frequency: 868,3 MHz (max. 0.36 mW)
433,92 MHz (max. 0.13 mW)
Voltage: 2 batteries 3V, CR 2032
Current input: approx. 11 mA
Size: 70 x 100 x 30 mm (B x H x T)
Weight: approx. 120 g
Protection category: IP 54
Range of temperature: -20°C to 60°C
Designated use
The radio code keypad is to be used to control door
operator and to switch on and off electrical devices
(power-operated units).
The Declaration of Conformity can be looked up at
the manufacturer mentioned in supply documents.
Simplified EU declaration of
conformity
Hereby, Marantec Antriebs- und Steuerungs technik
GmbH & Co. KG declares that the radio equipment
type Command 231 is in compliance with Directive
2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet
address:
www.marantec.com
᪾
Version: 09.2017
#70794
1 - GB 360232 - M - 0.5 - 0404
Gehäuseunterschale
2î€ Batterienî€ 3V,î€ CRî€ 2032
2 batteries 3V, CR 2032
Back cover of housing
Product specificaties
| Merk: | Marantec |
| Categorie: | Garagepoortopener |
| Model: | Command 231 |
Heb je hulp nodig?
Als je hulp nodig hebt met Marantec Command 231 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Garagepoortopener Marantec
19 Juli 2023
19 Juli 2023
19 Juli 2023
19 Juli 2023
19 Juli 2023
19 Juli 2023
19 Juli 2023
19 Juli 2023
19 Juli 2023
19 Juli 2023
Handleiding Garagepoortopener
- Garagepoortopener Abon
- Garagepoortopener Aperto
- Garagepoortopener Berner
- Garagepoortopener Budgetgaragedeuren
- Garagepoortopener Dickert
- Garagepoortopener DITEC
- Garagepoortopener Doco
- Garagepoortopener Doorsystems
- Garagepoortopener Einhell
- Garagepoortopener Entrematic
- Garagepoortopener FAAC
- Garagepoortopener Geba Tronic
- Garagepoortopener Goris
- Garagepoortopener Homentry
- Garagepoortopener Hormann
- Garagepoortopener Liftmaster
- Garagepoortopener MAC
- Garagepoortopener Novoferm
- Garagepoortopener Novotecnica
- Garagepoortopener Profitech
- Garagepoortopener Rademacher
- Garagepoortopener Seculux
- Garagepoortopener Silver
- Garagepoortopener Skylink
- Garagepoortopener Somfy
- Garagepoortopener Sommer
- Garagepoortopener Superrollo
- Garagepoortopener Tormatic
- Garagepoortopener Univer
- Garagepoortopener Craftsman
- Garagepoortopener Chamberlain
- Garagepoortopener Maveo
Nieuwste handleidingen voor Garagepoortopener
15 November 2024
28 September 2024
1 December 2023
2 Oktober 2023
2 Oktober 2023
16 September 2023
16 September 2023
16 September 2023
16 September 2023
16 September 2023