Makita AN943 Handleiding
Makita
Nietmachine
AN943
Lees hieronder de 📖 handleiding in het Nederlandse voor Makita AN943 (12 pagina's) in de categorie Nietmachine. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/12
1
ENGLISH (Original instructions)
INSTRUCTION MANUAL
IMPORTANT: Read Before Using.
Pneumatic Framing Nailer
AN923
AN943
007004
2
ENGLISH (Original instructions)
SPECIFICATIONS
Model AN923 AN943
Air pressure 0.44 - 0.83 Mpa (4.4 - 8.3 bar)
Nail Iength 50 mm - 90 mm
Nail capacity 64 - 74 pcs. 60 - 84 pcs.
Dimensions (L X H X W) 559 mm X 347 mm X 109 mm 455 mm X 365 mm X 109 mm
Min. hose diameter 8.5 mm
Net weight 4.0 Kg
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003.
END106-3
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
ï½¥ Read instruction manual.
ï½¥ Wear safety glasses.
ï½¥ Do not use on scaffoldings, ladders.
ENG905-1
Noise
The typical A-weighted noise level determined according
to EN792:
Model AN923
Sound pressure level (L
pA) : 89 dB(A)
Sound power level (L
WA) : 102 dB(A)
Uncertainty (K) : 3 dB(A)
Model AN943
Sound pressure level (L
pA) : 92 dB(A)
Sound power level (L
WA) : 105 dB(A)
Uncertainty (K) : 3 dB(A)
Wear ear protection
ENG904-1
Vibration
The vibration emission value determined according to
EN792:
Model AN923
Vibration emission (ah) : 4.0 m/s2
Uncertainty (K) : 1.5 m/s2
Model AN943
Vibration emission (ah) : 3.5 m/s2
Uncertainty (K) : 1.5 m/s2
ENG901-1
• The declared vibration emission value has been
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
• Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
ENH003-13
For European countries only
EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine:
Pneumatic Framing Nailer
Model No./ Type: AN923,AN943
are of series production and
Conforms to the following European Directives:
2006/42/EC
And are manufactured in accordance with the following
standards or standardised documents:
EN792
The technical documentation is kept by our authorised
representative in Europe who is:
Makita International Europe Ltd.
Michigan Drive, Tongwell,
Milton Keynes, Bucks MK15 8JD, England
3
30.1.2009
000230
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, 446-8502, JAPAN
ENB067-3
IMPORTANT SAFETY
INSTRUCTIONS
WARNING: WHEN USING THIS TOOL, BASIC
SAFETY PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED TO REDUCE THE RISK OF PERSONAL
INJURY, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
• For personal safety and proper operation and
maintenance of the tool, read this instruction
manual before using the tool.
• Always wear safety glasses to protect your eyes
from dust or nail injury.
WARNING: It is an employer's responsibility to
enforce the use of safety eye protection equipment
by the tool operators and by other persons in the
immediate working area.
• For Australia and New Zealand only
Always wear safety glasses and face shield to
protect your eyes from dust or nail injury. The safety
glasses and the face shield should conform with the
requirements of AS/NZS 1336.
WARNING: It is an employer's responsibility to
enforce the use of safety eye protection equipment
by the tool operators and by other persons in the
immediate working area.
Safety glasses
Face shield
000114
• Wear hearing protection to protect your ears
against exhaust noise and head protection. Also
wear light but not loose clothing. Sleeves should be
buttoned or rolled up. No necktie should be worn.
• Rushing the job or forcing the tool is dangerous.
Handle the tool carefully. Do not operate when
under the influence of alcohol, drugs or the like.
• General Tool Handling Guidelines:
(1) Always assume that the tool contains
fasteners.
(2) Do not point the tool toward yourself or
anyone whether it contains fasteners or not.
(3) Do not activate the tool unless the tool is
placed firmly against the workpiece.
(4) Respect the tool as a working implement.
(5) No horseplay.
(6) Do not hold or carry the tool with a finger on
the trigger.
(7) Do not load the tool with fasteners when any
one of the operating controls is activated.
(8) Do not operate the tool with any power source
other than that specified in the tool
operating/safety instructions.
• An improperly functioning tool must not be used.
• Sparks sometimes fly when the tool is used. Do not
use the tool near volatile, flammable materials such
as gasoline, thinner, paint, gas, adhesives, etc.;
they will ignite and explode, causing serious injury.
• The area should be sufficiently illuminated to
assure safe operations. The area should be clear
and litter-free. Be especially careful to maintain
good footing and balance.
• Only those involved in the work should be in the
vicinity. Children especially must be kept away at all
times.
• There may be local regulations concerning noise
which must be complied with by keeping noise
levels within prescribed limits. In certain cases,
shutters should be used to contain noise.
• Do not play with the contact element: it prevents
accidental discharge, so it must be kept on and not
removed. Securing the trigger in the ON position is
also very dangerous. Never attempt to fasten the
trigger. Do not operate a tool if any portion of the
tool operating controls is inoperable, disconnected,
altered, or not working properly.
• Operate the tool within the specified air pressure of
0.44 - 0.83 MPa (4.4 - 8.3 bar) for safety and longer
tool life. Do not exceed the recommended max.
operating pressure of 0.83 MPa (8.3 bar). The tool
should not be connected to a source whose
pressure potentially exceeds 1.37 MPa (13.7 bar).
• Make sure that the pressure supplied by the
compressed air system does not exceed the
maximum allowable pressure of the fastener
driving tool. Set the air pressure initially to the lower
value of the recommended allowable pressure (see
Product specificaties
| Merk: | Makita |
| Categorie: | Nietmachine |
| Model: | AN943 |
Heb je hulp nodig?
Als je hulp nodig hebt met Makita AN943 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Nietmachine Makita
10 Juni 2023
9 Juni 2023
9 Juni 2023
3 Juni 2023
2 Juni 2023
22 Mei 2023
20 Mei 2023
13 Mei 2023
21 April 2023
15 April 2023
Handleiding Nietmachine
- Nietmachine Bosch
- Nietmachine DeWalt
- Nietmachine Whirlpool
- Nietmachine Einhell
- Nietmachine Fellowes
- Nietmachine Gude
- Nietmachine Hikoki
- Nietmachine Hitachi
- Nietmachine Holzmann
- Nietmachine Iluv
- Nietmachine Kensington
- Nietmachine Leitz
- Nietmachine Meister
- Nietmachine Metabo
- Nietmachine Milwaukee
- Nietmachine Parkside
- Nietmachine Powerfix
- Nietmachine Powerplus
- Nietmachine President
- Nietmachine Proline
- Nietmachine Ryobi
- Nietmachine Sencor
- Nietmachine Silverline
- Nietmachine Targus
- Nietmachine Topcraft
- Nietmachine Vonroc
- Nietmachine Workzone
- Nietmachine Klein Tools
- Nietmachine Rapid
- Nietmachine Genesis
- Nietmachine Fieldmann
- Nietmachine Porter-Cable
- Nietmachine Sun Joe
- Nietmachine Rapoo
- Nietmachine Dedra
- Nietmachine MSW
- Nietmachine Craftsman
- Nietmachine Surtek
- Nietmachine Rexel
- Nietmachine Swingline
- Nietmachine Aqua Joe
- Nietmachine Abac
- Nietmachine CTA Digital
- Nietmachine Meister Craft
- Nietmachine Werckmann
- Nietmachine POWERNAIL
- Nietmachine Neo
- Nietmachine Syscom
- Nietmachine Mannesmann
- Nietmachine Smart365
Nieuwste handleidingen voor Nietmachine
3 December 2024
3 December 2024
15 Oktober 2024
27 Augustus 2024
15 Juli 2024
15 Juli 2024
15 Juli 2024
15 Juli 2024
15 Juli 2024
15 Juli 2024