Makita AN454 Handleiding

Makita Nietmachine AN454

Lees hieronder de 📖 handleiding in het Nederlandse voor Makita AN454 (28 pagina's) in de categorie Nietmachine. Deze handleiding was nuttig voor 46 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/28

INSTRUCTION MANUAL

MANUEL D'INSTRUCTION

MANUAL DE INSTRUCCIONES

Pneumatic Coil Nailer

Cloueur à rouleaux pneumatique

Clavadora Neumática de Carrete

AN454

IMPORTANT: Read Before Using.

IMPORTANT : Lire avant usage.

IMPORTANTE: Lea antes de usar.

2 ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: AN454

Air pressure 0.49 - 0.83 MPa (70 - 120 PSIG)

Nail length (L) x Shank diameter (D) L: 19 mm - 45 mm x D: 3.05 mm

(L: 3/4″ - 1-3/4″ x D: 0.120″)

Nail capacity 120 pcs.

Minimum hose diameter 6.5 mm (1/4″)

Dimensions (L x W x H) 256 mm x 117 mm x 271 mm

(10-1/8″ x 4-5/8″ x 10-5/8″)

Net weight 2.4 kg (5.2 lbs)

• Due to our continuing program of research and development, the specications herein are subject to change

without notice.

• Specications may differ from country to country.

SAFETY WARNINGS

Important safety instructions

For personal safety and proper operation and main-

tenance of the tool, read this instruction manual

carefully before using the tool.

WARNING: WHEN USING THIS TOOL, BASIC

SAFETY PRECAUTIONS SHOULD ALWAYS BE

FOLLOWED TO REDUCE THE RISK OF PERSONAL

INJURY, INCLUDING THE FOLLOWING:

READ ALL INSTRUCTIONS.

Personal Protective Equipment

1. Always wear safety glasses to avoid eye injury

from dust or fasteners. The safety glasses

should conform with the requirements of ANSI

Z87.1.

WARNING:It is an employer's responsibility

to enforce the use of safety eye protection

equipment by the tool operators and by other

persons in the immediate working area.

2. Wear hearing protection to protect your ears

against exhaust noise and head protection.

Also wear light but not loose clothing. Sleeves

should be buttoned or rolled up. No necktie

should be worn.

Flammable Atmospheres

1. Do not operate tool in explosive atmospheres,

such as in the presence of ammable liquids,

gases or combustible dust.

Tool modication

1. The tool should not be modied unless autho-

rized in the tool manual or approved in writing

by the tool manufacturer.

Tool maintenance

1. Refer to the tool maintenance instructions for

detailed information on the proper mainte-

nance of a tool.

Recommended fasteners and accessories

Use only fasteners made or recommended by the

tool manufacturer, or fasteners that perform equiv-

alently to those recommended by the manufacturer.

2. Use only accessories made or recommended

by the tool manufacturer, or accessories that

perform equivalently to those recommended

by the manufacturer.

Inspect tool before operating to:

1. Use only power source specied in the instruc-

tion manual.

Operate the tool within the specied air pres-

sure on the tool label for safety and longer tool

life. Do not exceed the recommended max.

operating pressure. The tool should not be

connected to a source whose pressure poten-

tially exceeds 1.38 MPa (200 PSIG).

2. Never use the tool with other than compressed

air. If bottled gas (carbon dioxide, oxygen,

nitrogen, hydrogen, air, etc.) or combustible

gas (hydrogen, propane, acetylene, etc.) is

used as a power source for this tool, the tool

will explode and cause serious injury.

Always check the tool for its overall condition and

loose screws before operation. Tighten as required.

4. Make sure all safety systems are in working

order before operation. The tool must not

operate if only the trigger is pulled or if only

the contact element is pressed against the

wood. It must work only when both actions are

performed. Test for possible faulty operation

with fasteners unloaded and the contact ele-

ment in fully pulled position.

Always check contact element as instructed in

this manual. Fasteners may be driven accidentally

if the safety mechanism is not working correctly.

Operating controls

1. Do not use a tool with missing or damaged

safety warning label(s.)

2. A tool that is not in proper working order must

not be used. Tags and physical segregation

shall be used for control.

3 ENGLISH

3. Do not remove, tamper with, or otherwise

cause tool operating controls to become

inoperable.

4. Do not operate tool if any portion of the tool

operating controls is inoperable, discon-

nected, altered, or not working properly.

Tool handling

1. Only persons who have read and understand

the tool operating/safety instructions should

operate the tool.

2. Always assume that tool contains fasteners.

3. Do not point tool toward yourself or anyone

whether it contains fasteners or not.

4. Keep bystanders and children away while

operating tool.

5. Do not actuate tool unless tool is placed rmly

against the workpiece.

6. Respect tool as a working implement.

7. Do not engage in horseplay.

8. Stay alert, focus on your work and use com-

mon sense when working with tools.

9. Do not use tool while tired, after having con-

sumed drugs or alcohol, or while under the

inuence of medication.

10. Do not overreach. Keep proper footing and

balance at all times.

11. Do not hold or carry tool with a nger on the

trigger.

12. Drive fasteners into proper work surface only.

13. Do not drive fasteners into other fasteners.

14. After driving a fastener, tool may spring back

(“recoil”) causing it to move away from the

work surface. To reduce risk of injury always

manage recoil by:

a) always maintaining control of tool.

b) allowing recoil to move tool away from

work surface.

c) not resisting recoil such that tool will

be forced back into the work surface. In

“Contact Actuation Mode,” if workpiece

contact is allowed to re-contact work

surface before the trigger is released, an

unintended discharge of a fastener will

occur.

d) keeping face and body parts away from

tool.

15. When working close to an edge of a workpiece

or at steep angles use care to minimize chip-

ping, splitting or splintering, or free ight or

ricochet of fasteners, which may cause injury.

16. Keep hands and body away from fastener

discharge area of tool.

17. Do not load tool with fasteners when any one

of the operating controls is activated.

18. Do not operate tool with any power source

other than that specied in tool operating/

safety instructions.

19. Do not operate tool with any operating pres-

sure other than that specied in tool operating/

safety instructions.

20. Always select an actuation system that is

appropriate to the fastener application and the

training of the operator.

21. Use extra caution when driving fasteners into

existing walls or other blind areas to prevent

contact with hidden objects or persons on

other side (e.g., wires, pipes.)

22. Do not lift, pull or lower tool by the hose.

Disconnecting tool

Disconnect tool from the power source when:

1. Not in use;

2. Performing any maintenance or repairs;

3. Clearing a jam;

4. Elevating, lowering or otherwise moving the

tool to a new location;

5. Tool is outside of the operator’s supervision or

control; or

6. Removing fasteners from the magazine.

Additional safety instructions

1. The area should be sufciently illuminated to

assure safe operations. The area should be

clear and litter-free.

There may be local regulations concerning

noise which must be complied with by keeping

noise levels within prescribed limits. In certain

cases, shutters should be used to contain noise.

3. Check walls, ceilings, oors, roong and

the like carefully to avoid possible electrical

shock, gas leakage, explosions, etc. caused by

striking live wires, conduits or gas pipes.

4. On rooftops and other high locations, drive

fasteners as you move forward. It is easy to

lose your footing if you drive fasteners while

inching backward. When driving against per-

pendicular surface, drive fasteners from the

top to the bottom. You can perform the opera-

tions with less fatigue by doing so.

5. Do not leave the loaded tool or the air com-

pressor under pressure for a long time out in

the sun. Be sure that dust, sand, chips and

foreign matter will not enter the tool in the

place where you leave it setting.

6. Perform cleaning and maintenance right after

nishing the job. Keep the tool in tip-top condi-

tion. Lubricate moving parts to prevent rusting

and minimize friction-related wear. Wipe off all

dust from the parts.

Do not connect or disconnect the air hose with

a nger on the trigger. An unexpected driving will

cause serious injury when the air hose is connected.

8. When you drop or strike the tool, check the

tool damage or crack and make sure that

safety systems are in working order before

operation. As there is high pressure inside the

tool, failure to do so will cause serious injury.

9. Ask Makita's Authorized service centers for

periodical inspection of the tool.

10.

To maintain product SAFETY and RELIABILITY,

maintenance and repairs should be performed

by Makita Authorized or Factory Service Centers,

always using Makita replacement parts.

SAVE THESE INSTRUCTIONS.

WARNING: MISUSE or failure to follow the

safety rules stated in this instruction manual may

cause serious personal injury.

Product specificaties

Merk:	Makita
Categorie:	Nietmachine
Model:	AN454

Heb je hulp nodig?

Als je hulp nodig hebt met Makita AN454 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Nietmachine Makita

Makita AF506 Handleiding

10 Juni 2023

Makita AT2550A Handleiding

9 Juni 2023

Makita DBN600ZJ Handleiding

9 Juni 2023

Makita AN613 Handleiding

3 Juni 2023

Makita T221DW Handleiding

2 Juni 2023

Makita T221D Handleiding

22 Mei 2023

Makita GN900 Handleiding

20 Mei 2023

Makita 242077-1 Handleiding

13 Mei 2023

Makita 242094-1 Handleiding

21 April 2023

Makita AN911H Handleiding

15 April 2023

Handleiding Nietmachine

Nieuwste handleidingen voor Nietmachine

Whirlpool YWEE515S0LV Handleiding

3 December 2024

Whirlpool YWEE515S0LB Handleiding

3 December 2024

MSW -STAPLER 1500 Handleiding

15 Oktober 2024

Abac G-301 Handleiding

27 Augustus 2024

Ryobi P322 Handleiding

15 Juli 2024

Ryobi P318 Handleiding

15 Juli 2024

Ryobi P317 Handleiding

15 Juli 2024

Ryobi P739 Handleiding

15 Juli 2024

Ryobi P330 Handleiding

15 Juli 2024

Ryobi P360 Handleiding

15 Juli 2024