M-System MVK-90 Handleiding

M-System Afzuigkap MVK-90

Lees hieronder de 📖 handleiding in het Nederlandse voor M-System MVK-90 (16 pagina's) in de categorie Afzuigkap. Deze handleiding was nuttig voor 9 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/16

INSTRUCTIONS FOR USE

GEBRAUCHSANWEISUNG

INSTRUCTIONS POUR L'EMPLOI

ISTRUZIONI PER L'USO

INSTRUCCIONES PARA EL USO

GEBRUIKSAANWIJZING

WARNING

-----------------------------------------------------------

The distance between the supporting surface for the

cooking vessels on the hob and the lower part of the

hood must be at least 65 cm. If the instructions for

installation for the hob specify a greater distance, this

has to be taken into account.

The air collected must not be conveyed into a duct used

to blow off smokes from appliances fed with an energy

other than electricity (central heating systems,

thermosiphons, water-heaters, etc.).

Comply with the official instructions provided by the

competent authorities in merit when installing the disposal

duct. In addition, exhaust air should not be discharged

into a wall cavity, unless the cavity is designed for that

purpose.

The room must be well aerated in case a hood and some

other heat equipment fed with an energy other than

electricity (gas, oil, coal heaters, etc) operate at the

same time. In fact the intake hood, disposing of air,

could create a vacuum in the room. The vacuum should

not exceed 0,04mbar. This prevents the gas exhausted

by the heat source from being intaken again. It is

therefore advisable to ensure the room contains air

taps able to ensure a steady flow of fresh air.

Check the data label inside the appliance; if the

symbol ( ) is printed, read the following: this

appliance has such technical particulars that it

belongs to class II insulation, therefore it must not

be earthed.

The following warning is valid in the United Kingdom

only: in case your cable is not furnished with a plug,

read the following instructions; as the colours of the

wires in the mains lead of this appliance may not

correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

– the wire which is coloured blue must be connected

to the terminal which is marked with the letter N or

coloured black;

– the wire which is coloured brown must be connected

to the terminal which is marked with the letter L or

coloured red.

– terminal of a three-pin plug.

Check the data label inside the appliance; if the

symbol ( ) is NOT printed, read the following:

ATTENTION: This appliance must be grounded. When

making the electrical connections, check that the

current socket has a ground connection.

The following warning is valid in the United Kingdom

only: as the colours of the wires in the mains lead of

this appliance may not correspond with the coloured

markings identifying the terminals in your plug, proceed

as follows:

– the wire which is coloured green and yellow must

be connected to the terminal in the plug which is marked

with the letter E or by the earth symbol [ ], or coloured

green or green and yellow;

English

– the wire which is coloured blue must be connected

to the terminal which is marked with the letter N or

coloured black;

– the wire which is coloured brown must be connected

to the terminal which is marked with the letter L or

coloured red.

When making the electrical connections, check that

the voltage values correspond to those indicated on

the data plate inside the appliance itself. In case your

appliance is not furnished with a non separating flexible

cable and has no plug, or has not got any other device

ensuring omnipolar disconnection from the electricity

main, with a contact opening distance of at least 3 mm,

such separating device ensuring disconnection from

the main must be included in the fixed installation. If

your unit features a power lead and plug, position this

so the plug is accessible.

Always switch off the electricity supply before carrying

out any cleaning or servicing operations on the

appliance.

USE

-----------------------------------------------------------

Avoid using materials which could cause spurts of

flame (flambées) near the appliance.

When frying, take particular care to prevent oil and

grease from catching fire. Already used oil is especially

dangerous in this respect. Do not use uncovered

electric grates.

To avoid possible risks of fire always comply with the

indicated instructions when cleaning anti-grease grille

and when removing grease deposits from the appliance.

MAINTENANCE

-----------------------------------------------------------

Thorough servicing guarantees correct and long-lasting

operation.

Particular care must be paid to the grease grille which

must be periodically cleaned in relation to use (at least

once every two months). Remove the grease grille and

wash them either by hand or in the dishwasher using

neutral detergent.

Any fat deposits should be removed from the appliance

periodically depending on amount of use (at least every

2 months). Avoid using abrasive or corrosive products.

To clean painted appliances on the outside, use a cloth

dipped in lukewarm water and neutral detergent. To

clean steel, copper or brass appliances on the outside,

it is always best to use specific products, following the

instructions on the products themselves. To clean the

inside of the appliance, use a cloth (or brush) dipped

in denatured ethyl alcohol.

DESCRIPTION

-----------------------------------------------------------

The appliance can be used in both the filtering and ducting

version.

In the Filtering version (Fig. 1), the air and vapours conveyed

by the appliance are depurated by charcoal filter(s) and

recirculated around the room. ATTENTION: Using the hood

as a filtering one it is necessary to use the charcoal filter(s)

that purifies the air sent back into the room.

In the Ducting version (Fig. 2), cooking vapours and odours

are conveyed straight outside by a disposal duct which

passes through the wall/ceiling. Use of charcoal filter is

therefore unnecessary.

According to the model you have bought, the appliance can

include 1 or 2 motors. In the I motor version the flange for

the air to be exhausted has not got a central position, but

it is slightly on the left.

INSTALLATION

-----------------------------------------------------------

Before assembling, in order to manoeuvre the appliance

more easily, take off the grease grille (Fig. 3): pull the front

of the grille upwards; desinsert the back from its seat.

IMPORTANT: So as not to damage your product, during

installation USE ONLY THE SCREWS PROVIDED. Make

sure these are used as shown in the following instructions.

To compensate possible depth voids between the appliance

and the wall, a plastic SPACING BAR to be fixed at the

back of the appliance by means of the three screws A is

included (Fig.4). The 3 screws A to be used are contained

in the accessory bag attached to the plastic spacing bar.

Cut the spacing bar according to the distance to be

adjusted.

Assembly under a pensile cupboard

The following operations are essential for as-sembly:

– Install the wiring system

– Prepare the air venting hole if your appliance is to be

installed in the Ducting version.

Fixation as indicated in Fig. 5:

Using the relative template make the 4 necessary fixing

holes in the bottom of the cupboard and cut the air venting

hole.

Move the hood close to the bottom of the wall unit and then

connect the two units by means of the 4 self-tapping

screws supplied together with the appliance.

Fixation with brackets as in Fig. 6 (optional):

Take the two brackets (S) out of the accessory bag

together with the 8 screws provided. Fit the brackets to

the wall unit being careful to position these correctly; for

this operation use the 4 longer screws. At this point,

secure the appliance to the brackets using the 4 shorter

screws.

Ducting version: connect the flange of the hood with the air

venting hole made previously in the wall/ceiling by means

of an adequate tube. Make the electrical connection of the

hood by means of the power supply cable. Assemble the

grease grille with the hood, inserting it obliquely (making the

front side go upwards).

Filtering version: connect a proper pipe to the flange of the

hood so that the air is sent outside the pensile and sent back

into the room. Make the electrical connection of the hood

by means of the power supply cable. Set the charcoal filter

(Fig. 7A) inside the grease grille blocking it by means of the

2 supplied metal wires (F), as indicated in Fig. 7; the 2 metal

wires must be threaded into the relevant slots.

Assemble the grease grille with the hood, inserting it ob-

liquely (making the front side go upwards).

OPERATION

-----------------------------------------------------------

Controls (Fig. 8):

A = ON/OFF 1st speed switch

B = II speed switch

C = III speed switch

The motor is automatically ON or OFF by opening/

closing the truck (unless switch A is on 0). Opening

the truck the motor works according to last speed

registered.

D = Light switch:position A (automatic), the light are

automatically regulated ON or OFF by the opening/

closing of the truck. Position M (manual), the light is

on. Position 0, the light is off.

In case the hood is a filtering version one, it is necessary

to change the charcoal filter(s) according to utilization

about every six month. To remove the filter:

– open the truck pulling it first downwards, then towards

the front.

– take off the grease grille: pull the front of the grille

upwards; desinsert the back from its seat.

– take off the charcoal filter (A) from the inside of the

grease grille taking off the 2 metal wires F (Fig. 7) that

blocks it.

Light bulb

- If the fluorescent light or incandescent lamps need

changing, slacken the light cover by disconnecting the

screw and remove the bulb itself (Fig. 9). Replace with a bulb

of the same type.

- To change the rectangular halogen bulbs open the cover

and remove the bulb without touching it with bare hands

(Fig.10). Replace with a bulb of the same type.

Product specificaties

Merk:	M-System
Categorie:	Afzuigkap
Model:	MVK-90

Heb je hulp nodig?

Als je hulp nodig hebt met M-System MVK-90 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Afzuigkap M-System

M-System MVK-90 Handleiding

25 Januari 2024

M-System MU-50 Handleiding

4 Juni 2023

M-System MSPK 760 IX Handleiding

26 Mei 2023

M-System MSDK 660 Handleiding

9 Mei 2023

M-System MSPK 660 IX Handleiding

8 Mei 2023

M-System MST-90 Handleiding

23 April 2023

M-System MSK-650IX Handleiding

20 April 2023

M-System MSPK 901 Handleiding

20 April 2023

M-System MSDK 961 Handleiding

20 April 2023

M-System MSPK 960 IX Handleiding

11 April 2023

Handleiding Afzuigkap

Nieuwste handleidingen voor Afzuigkap

Siemens LC64BB222T Handleiding

30 Januari 2025

Siemens LB56NAC60B Handleiding

30 Januari 2025

Siemens LC56KA270 Handleiding

30 Januari 2025

Whirlpool AKR 6390 IX Handleiding

30 Januari 2025

Novy 7210 Handleiding

3 Oktober 2024

Itho WD 03060 Curva Handleiding

6 Oktober 2024

Novy 7406 Handleiding

3 Oktober 2024

Summit SEH1524SSADA Handleiding

15 Januari 2025

Summit SEH1536SSADA Handleiding

15 Januari 2025

BEKO BHCB66741BBHS Handleiding

14 Januari 2025