LYYT DIY-PK60 Handleiding

LYYT Niet gecategoriseerd DIY-PK60

Lees hieronder de 📖 handleiding in het Nederlandse voor LYYT DIY-PK60 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 55 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
DIY LED TAPE KIT
User Manual
DIY LED TAPE KIT - SINGLE COLOUR
Introduction:
Thank you for purchasing the Lyyt DIY LED Tape . Kit LED tape is ideal for use on the underside of a counter tops, shelves, cupboards, around
window frames or in an alcove of a ceiling to name just a few examples.
Before starting please ensure that you have read this instruction leaflet carefully.
If you are unsure about any of the installation details, please have this installed by a competent installer.
Blister Contents:
1 x Reel of LED tape
1 x UK power adap tor
Possible Required tools: Scissors, Craft knife, Soldering iron and solder, 2 core DC wire and heat shrink tube.
Step 1: Preparation
Ensure that the surface you are attaching to is clear of dust and dirt. Clean thoroughly and leave to dry before fitting the tape.
Unravel the tape and connect the power supply. Check that all the LEDs are functioning correctly and if there are any faults return to your retailer
without delay.
Step 2: Cutti ng
WARNING: Disconnect from the power supply before attempting any cutting.
Measure out each section and cut with sharp scissors at the marked 5cm intervals to achieve the perfect length. Do not discard any excess tape as
it can be easily reconnected and used again (see FIG 2).
Step 3: Fitting:
Example 1: Simple straight run.
Clear the area you wish to install the tape and remove the backing paper, exposing the adhesive tape. Push tape firmly onto the surface. It is
recommended to work on 50cm sections at a time in order to ensure a professional finish. When you reach the end of your installation cut at the
marked cutting point.
Example 2: Requires cutting:
The tape can be cut at highlighted 5cm intervals for a perfect fit.
FIG 1:
DIY LED Tape User Manual Kit
You may also reconnect the two pieces by soldering the connection together (FIG 2). The tape has two tracks for the DC voltage with points +
positive pole at the top and negative pole at the bottom. –
To reattach, use a craft knife to cut the Epoxy coating from the terminals.
Use a soldering iron and solder to connect the DC wire to the relative terminals be sure not to cause a short circuit when making these connections,
as this will result in malfunction and possible damage to the power supply.
FIG 2:
WARNING: Only cut the tape on the highlighted intervals. Cutting the tape in other parts without due care will permanently damage that section
of the tape and will result in malfunction.
Points to remember when using this tape
1) Only use the supplied power adaptor for the length of tape in the kit
2) Only cut the tape at the highlighted 5cm intervals.
3) Do not connect another reel and operate from a single power supply as this will seriously affect the performance.
3) The top track of the tape is the + Positive pole.
4) The bottom track of the tape is the negative pole. –
5) Ensure you connect the correct wires otherwise the tape will not work.
6) Ensure that when soldering there are no short circuits
7) We recommend use heat shrink tubing to protect the connection. of
8) Check that everything operates correctly before installing.
FAQ:
Q) Can I connect different colours in a chain?
A) Yes all the LEDs draw the same power, current and have the same connection but do not exceed the full reel length.
Q) Can you cut a reel of tape into many different sections then connect them all together?
A) Yes as long as you cut the tape at 5cm intervals highlighted.
Q) I have connected two reels together off one power supply and the LEDs are dim towards the end.
A) The power adaptor is only designed to operate the reel in the kit. Anything longer will seriously affect the performance.
Q) Can I connect the tape together to form a loop?
A) Yes you can. This will even the brightness out on the LEDS across the reel length
Q) Can I use the tape outdoors?
A) Yes, the tape is IP65 rated. Ensure that the terminated ends are heat shrink protected.
Q) Can I clean the tape?
A) Yes, the tape is IP65 rated and has an epoxy coating. Just wipe down with a damp cloth regularly to ensure continuing brightness
Q) Can I replace / patch damaged tape with a new piece
A) Yes, just highlight the effected area by the 5cm intervals. Cut out the faulty section then fit in a new piece soldering the connections securely
and using heat shrink to protect the repaired connection.
Specifications
Voltage
12Vdc
Current consumption
340mA/m
Power consumption
4.08W/m
Number of LEDs
60/m
LED Spacing
16mm
Cut intervals
5cm
Beam angle
140° - 160°
LED type
SMD3528 or SMD2835
IP rating
IP65
DIY LED Tape User Manual Kit
LED DIY TAPE KIT - RGB MULTI COLOUR
Introduction:
Thank you for purchasing the Lyyt DIY RGB LED Tape. LED tape is ideal for use on the underside of a counter tops, shelves, cupboards, around
window frames or in an alcove of a ceiling to name just a few examples.
Before starting please ensure that you have read this instruction leaflet carefully.
If you are unsure about anything please have the tape installed by a competent installer.
Contents:
1 x Reel of RGB LED tape
1 x UK power adap tor
1 x Control Box with IR remote handset
Possible required tools: Scissors, Craft knife, Soldering iron and solder, 4 core DC wire and heat shrink tube.
Step 1: Preparation
Ensure the surface you are attaching to is clear of dust and dirt. Clean thoroughly and leave to dry before fitting the tape.
Step 2: Connecting IR Controller:
Connect the 4pin connector to the control box and then to the LED tape (FIG 1). Plug in the power supply and use the IR remote control to select
the various functions (Fig 2).
Unravel the tape to check that all the LEDs are functioning correctly. If there are any faults return to your retailer without delay.
FIG 1:
FIG 2:
Step 2: Cutting
WARNING: Disconnect from the power supply before attempting any cutting.
Measure out each section and cut with sharp scissors only at the marked 10cm intervals. Do not discard any excess tape as it can be easily
reconnected and used again (see FIG 4).

Product specificaties

Merk: LYYT
Categorie: Niet gecategoriseerd
Model: DIY-PK60

Heb je hulp nodig?

Als je hulp nodig hebt met LYYT DIY-PK60 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd LYYT

LYYT

LYYT CLIP10-B Handleiding

5 Januari 2024
LYYT

LYYT DIY-CW60 Handleiding

5 Juli 2023
LYYT

LYYT PS30-24 Handleiding

23 Juni 2023
LYYT

LYYT LT24560-BL Handleiding

20 Juni 2023
LYYT

LYYT DIY-B60 Handleiding

19 Juni 2023
LYYT

LYYT DIYH-RGB30 Handleiding

16 Juni 2023
LYYT

LYYT LT12560-WW Handleiding

15 Juni 2023
LYYT

LYYT PS40 Handleiding

15 Juni 2023
LYYT

LYYT RGB10-F Handleiding

15 Juni 2023
LYYT

LYYT LT12560-CW Handleiding

14 Juni 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Livarno Lux

Livarno Lux IAN 071407 Handleiding

29 November 2024
Livarno Lux

Livarno Lux IAN 317128 Handleiding

29 November 2024
Livarno Lux

Livarno Lux IAN 049213 Handleiding

29 November 2024
Livarno Lux

Livarno Lux ST-1002 Handleiding

29 November 2024
Livarno Lux

Livarno Lux HG02489 Handleiding

29 November 2024
Livarno Lux

Livarno Lux HG02189 Handleiding

29 November 2024
Livarno Lux

Livarno Lux IAN 365198 Handleiding

29 November 2024
Livarno Lux

Livarno Lux IAN 367074 Handleiding

29 November 2024
Livarno Lux

Livarno Lux HG00701 Handleiding

29 November 2024
Livarno Lux

Livarno Lux IAN 337273 Handleiding

29 November 2024