LYYT CLIP10-B Handleiding


Lees hieronder de đź“– handleiding in het Nederlandse voor LYYT CLIP10-B (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 44 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
www.avsl.com lyyt COB LED Strip Manual
24V Seamless COB LED Strip 5m
User Manual
Introduction
Lyyt Seamless COB LED Strip provides a continuous 'no spot' linear lighting solution. The COB
(chip on board) technology consists of 528 tightly packed LED's per metre and a phosphor
layer coating which diffuses the LED's into a seamless array of light. The flexible COB strip is
supplied on a 5m reel and can be cut to desired length along the designated cutting points.
The 24Vdc COB strip has a CRI (Colour Rendering Index) of 90 making it suitable for a wide
variety of applications, such as in hospitality, retail, offices, displays, exhibitions and more.
IP20 versions are for indoor use only.
Specification
Colour temperature
156.6 UK: 6500K, 156.6 UK: 75 76 2700K
Voltage
24Vdc
Beam angle
12 0°
LED Ty pe
Sanan
Reel Length
5m
IP Rating
IP65
Power consumption p/m
12W
Current p/m
500mA
LED quantity p /m
528
LED spacing
2mm
Cut points
4.5cm
Colour rendering index
Ra>90
Cross-secti on
12 4 x mm
Weight
300g
This product is intended to be professionally installed, observin relevant electrical safety procedures. g
Lyyt COB Strip has a self-adhesive backing to allow it to be easily attached to a cl n, non-porous ea
surface.
www.avsl.com lyyt COB LED Strip Manual
Where less than 5m of tape is needed, there are solder points as shown below, where the tape may be
cut to size. These cut points are at 4.5 intervals. -connect to another length of tape after cm To re
cutting - - shown below. Some accessories are , solder a wire from “+” to “+” and a wire from “ ” to “ ” as
supplied with the tape reel for this purpose For best protection of this tape, we recommend inserting .
the tape into one of our Aluminium Profiles.
Each 5m reel of COB Strip is fitted with a 2.1mm DC jack for power input for easy connection to a
power supply. This connector may be removed and stripped for bare wire connection if a 2.1mm jack is
not fitted to the power suppl y.
If the power supply has enough capacity to power more than one reel, another reel can be connected
to the end of the first reel via the 2.1mm DC jack.
For 24V COB Strip, up to m can be linked in this manner. Using a separate wire to loop -25 “+” and “ ”
back to the power supply will help to avoid dimming at the far end through voltage drop. To connect
beyond these lengths, a parallel wire must be run from the power supply to the further reels of tape.
It is imperative that the power supply should have higher than the rated capacity in Amps (A) for the
current required to power the length(s) of COB Strip installed. Likewise, if controllers and
amplifiers/repeaters are used, these must have adequate capacity for the tape being controlled Please .
see the table below for reference.
Tape Length
5m
10m
20m
25m
Current for 24V tape 528 LED/m
2.5A
5A
10A
12.5A
Please visit www.avsl.com to select from our range of Vdc power supplies that are suitable for 24
powering Lyyt COB Strip s.
This p d t is classed as Electrical or Electronic equipment and should not disposed with othe household or ro uc be r
commercial waste at the end of its useful life. T goods must be disposed of according to your local council guidelines. he
Errors and omissions excepted.
Copyright© 22 AVSL Group Ltd Unit 2 Bridgewater Park, AVSL (Europe) Ltd, Unit 3D North Point Hou 20 , se,
Taylor Road, Trafford Park, Manchester. M 7JQ. North Point Bus. Park, New Mallow Road, Cork, Ireland. 41


Product specificaties

Merk: LYYT
Categorie: Niet gecategoriseerd
Model: CLIP10-B

Heb je hulp nodig?

Als je hulp nodig hebt met LYYT CLIP10-B stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd LYYT

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd