LYYT AL2-S1612 Handleiding


Lees hieronder de đź“– handleiding in het Nederlandse voor LYYT AL2-S1612 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
www.avsl.com lyyt COB LED Strip Manual
24V COB LED Strip 5m - RGB
User Manual
Introduction
Multi-colour RGB COB LED Strip by Lyyt provides a continuous linear lighting solution. The
COB (chip on board) technology consists of 840 tightly packed LEDs per metre. The flexible
COB strip is supplied on a 5m reel and can be cut to desired length along the designated
cutting points, the strip is equipped with an adhesive backing for easy installation. The 24Vdc
COB strip is suitable for a wide variety of applications, such as in hospitality, retail, offices,
displays, exhibitions and more. IP20 versions are for indoor use only.
Specification
LED Colour
RGB
Voltage
24Vdc
Beam angle
120°
LED Type
Sanan
Reel Length
5m
IP Rating
IP20
Power consumption per metre
11.64W
Current
485mA per metre
LED quantity per metre
840
LED spacing
0.97 mm
Cut points
50 mm
Colour rendering index
Ra>80
Cross-secti on
10 x 2.2mm
Weight
126g
Installation of this COB Strip should be carried out by competent electrical installers, observing the
relevant electrical safety procedures. Lyyt COB Strip has a self-adhesive backing to allow it to be easily
attached to a cl n, non-porous surface. ea
Where less than 5m of tape is needed, there are solder points as shown below, where the tape may be
cut to size. These cut points are at 5 intervals. -connect to another length of tape after cuttingcm To re ,
solder a wire from “+” to “+” and a “ ” “ ” “ ”wire from G , R and B as shown below. Some accessories are
www.avsl.com lyyt COB LED Strip Manual
supplied with the tape reel for this purpose Alternatively, you can use solderless connectors to .
achieve this result For best protection of this tape, we recommend inserting the tape into one of our .
Alumini Profiles. um
Each 5m reel of COB Strip s bare wire ends to allow easy connection to an RGB controller and power ha
input .
If the power supply has enough capacity to power more than one reel, another reel can be connected
to the end of the first reel. Using an amplifier repeater will ensure that extension reels mimic the
colour changes and brightness of the original reel .
It is imperative that the power supply should have higher than the rated capacity in Amps (A) for the
current required to power the length(s) of COB Strip installed. Likewise, if controllers and
amplifiers/repeaters are used, these must have adequa capacity for the tape being controlled Please te .
see the table below for reference. It is advised up to 25m of LED COB strip can be connected .
Tape Length
5m
10m
20m
25m
Current for 24V tape 840 LED/m
2.425A
4.85A
9.7A
12.125A
Please visit www.avsl.com to select from our range of Vdc power supplies that are suitable for 24
powering Lyyt COB Strip
This p d t is classed as Electrical or Electronic equipment and should not disposed with other household or ro uc be
commercial waste at the end of its useful life. The goods must be disposed of according to your local council guidelines.
Errors and omissions excepted.
Copyright© 22 AVSL Group Ltd Unit 2 Bridgewater Park, AVSL (Europe) Ltd, Unit 3D North Point Hou 20 , se,
Taylor Road, Trafford Park, Manchester. M 7JQ. North Point Bus. Park, New Mallow Road, Cork, Ireland. 41


Product specificaties

Merk: LYYT
Categorie: Niet gecategoriseerd
Model: AL2-S1612

Heb je hulp nodig?

Als je hulp nodig hebt met LYYT AL2-S1612 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd LYYT

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd