Lockwood 8653 Handleiding

Lockwood Niet gecategoriseerd 8653

Lees hieronder de 📖 handleiding in het Nederlandse voor Lockwood 8653 (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 59 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

Part No. 8653-221 Iss. B 0916

‘O’ Ring

Locating

Lugs

‘O’ Ring

Ensure Actuating bar

and Rods are assembled

as shown prior to assembly

to the door frame. With

the ‘TOP’ mark facing the

top of the door.

Top Lock

Locating

Lugs

Actuating

Bar

Rod

Keeping the Locating Lugs of

the Actuating bar facing the

front edge of the stile, insert

the rod assembly through

the top cut-out, and slide

it through the door

section. With the Top

lock in the locked

position, connect the

rod and push into place.

Pull bottom rod end through bottom

cut-out. Connect to Bottom Lock, and

push into place.

LOCKWOOD 8653 SECURITY

SLIDING 3 POINT DOOR LOCK

Mounting of the Handle below the centreline

Both sides of the door stile must be cut out to

the dimensions given. Start with the centreline

of the door.

Both sides of the door stile must be cut out to

the dimensions given. Start with the centreline

of the door.

Mounting of the Handle above the centreline

INSTALLATION INSTRUCTIONS

1a 1b

Press here

with screwdriver

Step A Ensure the lock is in the Red

“Locked” position. Gently push the

bottom lock until it stops.

Drill a Ø3mm hole in the centre

of the slot, and loosely fit the first

fixing screw.

Step B Push the lock towards the

bottom of the door, tighten the

first screw.

Check the beak position as per

Step 4. Unlock and lock the

main lock to check operation.

Ensure the lock is in the Red

“Locked” position, drill and

fasten the second

screw.

Installation of Bottom Auxilary Lock

Installation of Top Auxilary Lock

Step A Ensure the lock is in

the Red “Locked” position. Gently

push the top lock until it stops.

Drill a Ø3mm hole in the centre of

the slot, and loosely fit the first

fixing screw.

Step B Push the lock towards the

top of the door, tighten the

first screw.

Check the beak position as per

Step 4. Unlock and lock

the main lock to check operation.

Ensure the lock is in

the Red “Locked” position, drill

and fasten the second screw.

For correct function ,

the beak should remain

secure when pressure is

applied in deadlocked

state.

To check correct function,

deadlock the door and

apply downwards pressure

with a screw driver, in position

shown. If the beak releases, the lock is

now out of sync. Re-sychronise the lock and

adjust the lock slightly downwards. Deadlock,

and repeat test until the beak is secure.

Re-sychronising the Lock

If the lock is out of sync and

cannot be operated, remove

the furniture plates and

indicator assembly.

Insert a small flat head screw

driver into the indicator

mechanism as shown. Turn the

mechanism in the key locking

direction. Check the operation of the lock.

Checking of Top and Bottom Auxilary Locks

For the main lock drill two

Ø3mm holes and fit to door

jamb where marked using

12mm countersunk screws.

Adjust striker to correct

position and then tighten

screws. For timber

jambs, use longer

10g screws provided.

Repeat the process

with the top and bottom

strikers using the 8g screws

provided.

Use larger

strikers on Top

and Bottom locks

Use smaller

striker on the

Main lock

Mounting the Striker

With the strikers inserted in the

main lock body, and the top and

bottom locks, either mark the

position on the outside of the

jamb or remove the backing from

the tape and allow the strikers to

stick to the frame. Remove

strikers from locks.

After ascertaining the handing configuration required, simply click

the desired handle plates together and install the operating levers

and external restrictor plate as required. Then secure the furniture

plates to the door section using the two 25mm screws &

plugs supplied.

For further installation detail, reference the

standard 8653 Instructions

Restrictor plate to

External Side

Click together the External

Escutcheon Plate and the

Pull Handle, before

securing to the door

Click together the Internal

Escutcheon Plate and the

Pull Handle, before

securing to the door

Product specificaties

Merk:	Lockwood
Categorie:	Niet gecategoriseerd
Model:	8653

Heb je hulp nodig?

Als je hulp nodig hebt met Lockwood 8653 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Lockwood

Lockwood 001 Touch Handleiding

13 Juli 2023

Lockwood 8653 Handleiding

13 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Panasonic NB-W250 Handleiding

25 November 2024

Alpine CHM-S611 Handleiding

25 November 2024

AOpen DE3650-C Handleiding

25 November 2024

Lazer Urbanize MIPS Handleiding

25 November 2024

Symmons Dia 353GB-24 Handleiding

25 November 2024

SoundTube IPD-RS62-EZ Handleiding

25 November 2024

Moen Camerist 4905 Handleiding

25 November 2024

Lazer Cameleon DLX Handleiding

25 November 2024

DMT DLD-85 Handleiding

25 November 2024

AOpen AM1120T Handleiding

25 November 2024